Search Documents

By Boden A

A procedure was developed for recovering metal values from copper-smelter fume. The fume is first leached to neutrality with dilute sulphuric acid to obtain a solution of zinc sulphate containing a low level of impurities. The tailings from this leach are treated with hydrochloric acid in two stages, in which tin and zinc are quantitatively leached and recovered as a tin concentrate and a zinc sulphatelzinc chloride solution.About 80 per cent of the lead sulphate is converted into lead chloride, which can be recovered as a pure product.Data on the effect of temperature, acid concentration, aeration, and solid/liquid ratios on the hydrochloric acid leach are presented, and the fate of the most important metals during the recovery process is described. Alternative treatments of the tailings from the neutral sulphuric acid leach were briefly investigated.

Jan 1, 1977

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880s with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978 - 1981 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6 per cent Sn). Spectrum Resources Australia Pty Limited acquired a 98 per cent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to 1 mm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of six to seven years.

Jan 1, 1990

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

A brief review is given of the history of the Colliery to date together with the reasons for the development of an additional seam.Investigations into the quality of the coal ami its suitability for the production of metallurgical coke and determination of the economic mining limits and coal reserves are discussed. The commencement of mining operations and the inter-seamarrangements necessary for the disposal of coal won are described with the stages in the opening out of the seam itself and the reasons for the installation of a 48-in. trunk conveyor belt. Choke and manning of face equipment are considered and also the work of secondary development and pillar extraction.It is concluded that with modern face equipment and conveyor belt lines, concentrated mining followed by immediate extraction of pillars is practicable and is giving excellent results at Burwood Colliery.INTRODUCTIONBurwood Colliery, the total holding of which now comprises some 3,140 acres of land and 1,450 acres of sea leases, has mined the Borehole Seam since 1883. The early work took place from Nos. 1 and 2 shafts at Glenrock Lagoon and later on at Nos. 3 and 4 shafts at Whitebridge to which the centre of operations shifted in 1893, shaft sinking at this latter area having commenced in 1888.As all the early operations were confined to the Borehole Seam, reserves of coal on this horizon had been considerably reduced by the mid 1930's, so a cross measure drift was driven to the Victoria Tunnel Seam which is about 300 ft. above the Borehole Seam, and fully mechanized coal winning commenced from the second seam in 1938. Subsequently this cross measure drift was extended to the Borehole Seam and complete mechanization of the south-west sections of this seam achieved by 1945.Four track mounted mechanical units were put into operation in the latter area and these worked in a southerly and...

Jan 1, 1958

Fire-clay blocks lining the combustion chambers of zinc concentrate flash-roasting, furnaces operating at 1,000-1,200° C. have suffered moderately rapid deterioration due to slagging. The attack is accentuated by high temperatures, and is probably caused by lead oxide volatilized from the roasted concentrate.Resistance of refractories to attack increased with increasing alumina content from 30 to 45 per. cent but at 90 per cent alumina spalling was troublesome. Magnesite bricks were'subject to some spalling, but some types may lie satisfactory. Chrome and chrome-magnesite bricks spalled seriously.Material thought to be suitable for use as a monolithic lining slagged badly and an alternative may be tested.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Ltd. uses two multi-hearth furnaces and four flash or suspension roasting furnaces for the roasting .of zinc concentrates at its Risdon Works. The hearth roasting plant has been described previously by Forster (1949).A brief descriptioI1 of the first three flash roasters was given by Gordon and Forster (1955). A fourth flash roasting furnace began operation early in 1957. This furnace is somewhat larger than the earlier furnaces, and the designed capacity is also higher, auxiliary equipment being altered to suit. An important structural difference between the older furnaces and the fourth flash roaster is that the walls of the combustion chamber of the new furnace are lined with high alumina fire-bricks instead of fire-clay blocks. Thischange was made because the fire-clay blocks in the older flash roasters had shown s-evere wastage due to slagging by lead derived from the concentrate.

Jan 1, 1959

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By P A. Tilyard

There have been enormous changes in mineral processing in the past four decades. For example grinding mill power has increased by an order of magnitude, regrinding is done to -10 microns and flotation machines are 100 times bigger. Operating staff have unprecedented opportunities for online monitoring and performance control of mineral processing plants. Sophisticated instruments can provide a plethora of data characterising the mineralogy and surfaces of particles. Digital computers allow complex calculations on huge amounts of data including modelling and simulation of machine and plant performance. However, all these changes have not necessarily lead to better metallurgical results. An analogy can be drawn with the thoroughbred racing industry in Australia. Significant advances in scientific knowledge in animal genetics, physiology, biomechanics and nutrition applied to the business have resulted in only a two per cent reduction in winning times for the Melbourne Cup and Caulfield Cup since the 1920s. A critical look at some mineral processing metrics suggests similar failures to improve performance despite putting in more resources. In fact certain parameters such as operating times and plant start-up performance are considered to have remained static or even deteriorated. There has been an emphasis on 'process' at the expense of 'outcomes'. The industry's strength has been in finding technical (or 'hardware') solutions while its weakness has been at the people end of the business in maximising and consolidating the gains from the technologies. Some trends in plant design over these years have exacerbated the apparent deskilling of operating and technical staff. Despite unparalleled options for communications, some staff are embarrassingly uninformed about technical developments in their fields. The 'boom and bust' cycles of the industry, together with trends in tertiary education and the effects of fly-in, fly-out (FIFO) operations, raise serious questions about the sustainability of human capital in the mineral processing sector. This paper by two experienced mineral processing engineers, with contributions from other senior practitioners, reviews these trends. While there may be an element of 'the older we are, the better we were', it is an attempt to identify the issues and propose solutions.

Jan 1, 2009

Influence of Frothers on Bubble Shape and Velocity Close to the Generation Point

Sep 13, 2010

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

By Taylor G. H

The Triassic Ipswich (SE. Queensland) coals are of bituminous rank. The more exact rank of individual samples was determined by measuring the reflectance of the vitrinite. While in general the rank of the coals increases with stratigraphic depth, minor reversals, probably related to igneous intrusions, occur.The Ipswich coals form a coherent group so far as petrographic type is concerned. All are comparatively rich in vitrite and clarite, cutinite being the common maceral of the exinite group. The mineral contents of all the coals are comparatively high, clay and quartz being most abundant. The coals appear to be of essentially autochthonous origin, and to have been formed under conditions of fairly rapid subsidence.While the use of the coals is at present restricted to combustion, most have pronounced coking properties, as would be predicted from their petrographic composition and reflectance. However, the high mineral content of the coals would be a limiting factor in their use for coke-making.INTRODUCTIONDuring the last ten years, the Division of Coal Research, Commonwealth Scientific and Industrial Research Organization has carried out an extensive investigation of Australian coals, providing a wide range of analyses of most of the important of them. Special attention has been given in recent years to Queensland coals.Most seams were sampled as a number of subsections, enabling the internal variations, as well as the overall properties, to be assessed. The lenticularity of many of the mineralrich layers may tend to limit the significance of the samples, particularly in respect of ash yield, but although the vertical distribution of mineral matter may vary considerably from one sampling position to another, the lateral variation of the total mineral matter in the whole seam may not be great.Apart from extensive chemical analyses and utilization...

Jan 1, 1963

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very' high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the 'Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the· normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960

This paper reviews the current techniques employed in the prediction of subsidence and how they have been applied to partial extraction systems. The method using influence functions to describe the shape of the profile is investigated in detail and has been adopted to model the subsidence over workings in Huntly. It is compared with the profile methods developed in the United Kingdom and found to predict the subsidence profile more accurately than these methods.

Jan 1, 1991

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By Van Dusen M

The involvement of concerned parties in all aspects of the Lihir Project from an early stage has promoted good relations between all groups. Activities involving landowners, the Lihir community, the New Ireland Provincial Government (NIPG) and the prospective developer include the Lihir Liaison Committee, Lihir Working Group, Environmental Planning Committee, Provincial Mining Task Force and the Lihir Mining Area Landowners Association (LMALA). With modifications, the Lihir Liaison model may be of use in promoting good relationships among parties in other mineral developments.

Jan 1, 1991

By P Goblet, S A. Séguret, E Cordier, A Galli

In salar-type deposits, lithium grades can be measured by bailers introduced at different elevations in the drill holes at locations where, later, the brine will be pumped out to recover the metal. When they are duplicated, these a priori rudimentary measurements may show large differences without indicating whether this is due to the procedure itself or to some physical causes linked to the dynamic behaviour of the salar (seasonality, rainfall, underground flow etc). In the reservoir presented in the paper, the problem is complicated by the double lack of stationarity of the lithium grades: the grades not only increase importantly with the depth but at the same time their fluctuations decrease, making it necessary to use non-stationary geostatistical techniques to simulate them. Reservoir simulation is developed in two steps: first, geostatistical simulations of the lithium grade create possible realisations of the reservoir; then, each geostatistical simulation is followed by a pumping simulation that calculates, at each drill hole of a given extraction scenario, the lithium produced each year over 40 years. For the set of 100 simulations produced in this way, a scenario reduction is made to choose the five most representative simulations where more complex calculations will be carried out (for example, changing hydrogeological parameters such as porosity and permeability, or the elevation of the filters, the number and the location of the pumping and the reinjection drill holes etc). The paper first presents an analysis of the geostatistical model sensitivity to the grade uncertainty when measured by bailer. Among the 100 measurements at our disposal covering the future production domain, 50 per cent are duplicates measured at the same place but at different times. They are randomly sampled to produce five subsets of 75 values, which will constitute the future 3D conditioning points for the geostatistical analysis and the simulations. For each subset, trend, standard deviation and variogram models are fitted, leading to five sets of 20 geostatistical simulations of grades. In this way, the reliability of the different parameters involved in the procedure is evaluated, as well as its impact on the pumping results. Then, a reconciliation study is conducted between the non-stationary nugget effects encountered in the 3D variograms of the lithium grade and a pure statistical analysis of 25 duplicates measured at different locations and/or different times. The result is that if the nugget effect reaches 20 per cent, which is the case of three conditioning subsets out of five, the reconciliation is good and the nugget effect of the variogram model represents the bailer uncertainty, ie the measurement error. Since the geostatistical simulation incorporates a nugget effect, it handles the bailer uncertainty and the impact on the produced metal is included in the evaluation. The final conclusion is that, after the hydrogeological pumping simulations, the initial differences between the five geostatistical models do not influence the final results: lithium grades measured by bailers can lead to a robust evaluation of the extractable resources, a conclusion that conflicts with conventional wisdom.CITATION:Séguret, S A, Goblet, P, Cordier, E and Galli, A, 2017. Bailer uncertainty evaluation in a lithium salar deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 395–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Two events during the past decade have combined to effectively alter the role of the geologist working in Papua New Guinea. The gold boom of the 1980s resulted in a substantial increase in the general awareness at village level of mining companies, gold and landowner issues, and as a consequence of the Bougainville tragedy, landowners are also very much aware of the potential problems of a mining operation in their area. Landowners know they have the power to remove a company from a project area, and government has shown itself to be virtually powerless and unable to help the company effectively. During a considerable proportion of a project's development time, the project geologist is viewed in the eyes of the local community as the 'company'. Good landowner relationships are nurtured over a reasonable time period and the input of the geologist is significant in determining the eventual fate of company-landowner relationships. The initial impressions of the company, gathered by the local community, will have a far reaching impact on the nature and direction of their future exchanges with the company.

Jan 1, 1991

TIMBER supports for large underground cavities are temporary expedients until the permanent filling can be put in. Nevertheless, timber supports are very necessary in some form. The general problem is to support the cavity in all directions withthe minimum of timber, disposed in the strongest way. The simplest way of filling an irregular space with timber sets is to form triangles.The right-angled isosceles triangle (Fig. 1) leads to the true square set, in which caps are equal to struts. The right-angled unequal-sided triangle and the scalene isosceles triangle (Fig. 2) lead to the oblong square set, where caps are longer than struts.The scalene triangle (Fig. 4) leads to the rhombic or oblique set. The equilateral triangle leads to the hexagon set (Fig. 3), in which the caps and struts are all equal. These five plane figures, the triangle, square, rectangle, rhomb and hexagon, are the only figures that will completely fill any irregular plane figure, without interstices. Hexagon sets were first suggested by the writer in 1902 to a mine manager at Broken Hill, who did not see his way to use them.

Jan 1, 1912

THE area dealt with in this paper is included within a radius of about 3 miles of the Poimena township. Several thousand tons of tin have been won from this field, and probably £200,000 spent in exploiting it.PREVIOUS LITERATUREThe field has been reported on by Government geologists on four occasions and several ,articles on it have appeared in the mining journals. The work done by Government geologists is summarized below:-"Report on the Blue Tier Tin Mining District and its Tin Deposits", 1886.Speaking of the tin-ore occurrences, this paper states:-"In the primary granite the lodes of tin ore occur, also dykes and belts of more recently obtruded porphyries. The really valuable metalliferous deposits may be classified as follows :-1. Lodes (of which the Lottah mine is typical).2. Dykes- (a) Indurated or hard (as shown by the formations at the Anchor and Cream Creek mines). (b) Soft (eg Hayley's Lease).

Jan 1, 1912

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

Holla has given a good background to the various methods of subsidence control in the coalfields around Sydney.The present writer notes that in many cases, especially with wide longwall panels, there is not the flexibility to alter the mine layout as there is to some degree with the various pillar extraction methods. For this reason it may not be possible to plan the workings to minimise subsidence and some damage to structures may occur. The cost of repair or the cost of subsidence provisions to minimise damage may be small in relation to the tonnages of coal which would otherwise have to be sterilised. One method of subsidence control which has been in use in the Newcastle area since 1970 is the panel and pillar layout (partial extraction layouts with stable pillars). An extracted panel width of 0.6 times the depth of cover resulted in a maximum subsidence of 115 mm for an extracted seam thickness of 2.2 m.As Holla points out, the extracted panel widths in relation to th depth of cover depend on the particular geological setting. His Fig. 3 shows that the subsidence over a panel width of 0.3 times the cover depth in the Southern Coalfield is the same as over a panel width of 0.55 to 0.6 times the cover depth in the Northern Coalfield.Selective pillar extraction and longwall mining can both be used in the panel and pillar layout. Holla's Figs 2 and 3 are used to estimate the maximum subsidence over an extracted panel of known geometry. Maximum subsidence is related to seam thickness. What provision is made for a reduction in subsidence due to the coal which remains behind in a pillar extraction panel if the pillar recovery is poor? The writer suggests that an effective seam height could be used, based on the actual mining height reduced by a factor to account for the percentage recovery of coal from an extracted panel.

Jan 1, 1986