Search Documents

F. JOHNSON,* Birmingham, England (written discussion t).--. Mr. Skowronski's first melting experiments tend to show that ingots with a "level set" may be obtained without oxygen. Now it is characteristic of all metals which occupy a smaller volume when solid than they do when molten to "pipe." In vertical-cast ingots, this pipe resembles a horn-shaped cavity, with the wide mouth uppermost. In horizontal-cast ingots, the pipe is a longitudinal furrow along the center-line of the ingot surface. If copper be successfully deoxidized and degasified, this furrow will inevitably be produced. In the author's oxygen-free ingots, it is. clear that gases were occluded and these gases effectively opposed the formation of a pipe or furrow by shrinkage (fluid contraction). It is riot a special property of any particular gas which produces this effect. Hence it is not surprising that the author has succeeded in producing level and overpoled ingots through the agency of sulphur. dioxide gas. That he has counteracted the overpoling influence of sulphur by means of oxygen is somewhat difficult to explain, since the well known reaction between cuprous sulphide and cuprous oxide should result in the production of sulphur dioxide gas. Why the presence of excess cuprous oxide should neutralize the overpoling influence of this gas without eliminating sulphur is not at all clear. It is to be regretted that the oxygen was not determined in the bars given in Tables 3 and 4. It is by no means established that sulphur is responsible for the over, poling of ingots given in Table 4, since carbon was used for overpoling. If, however, the same kind of poling treatment was given as that applied in the case of ingots in Table 1, the responsibility of sulphur assumes more definite shape. The author rightly points out that Mr. Johnson's theory of the equilibrium between gases and cuprous oxide does not explain why a simple addition of cuprous oxide does not correct an overpoled charge. Such a charge must be re-worked to "set" copper. This re-working (rabbling) undoubtedly forcibly removes the excess gases, which are not removable by cuprous oxide.

Jan 11, 1918

Francis Drake, Bulawayo, Rhodesia, So. Africa (communication to the Secretary *):—I should like to place on record some data in addition to those given by Mr. Canby in his paper. I regret that my notes have been destroyed so that I can give no accurate measurements of the water jacket that I am about to describe. This furnace mas erected in Cerro Gordo, Inyo county, Cal., early in 1875, and I think it quite possible that it was the first applied in lead smelting. It was made of plate iron and elliptic in shape, the inner dimensions being about 54 by 42 in. by 48 in. high. The distance between the inner and outer plates was about 6 in. Tuyere holes, one at the back and two on each side, about 12 in. in diameter, were made in this, and in these were placed cast-iron water tuyeres about 16 in. long, the diameter of the blast orifice at the point being about 3 in. The height from tuyeres to feed door was about 9 ft., but the top of the charge was kept about 5 ft. above the tuyeres. There was a space of about 12 in. between the jacket and the top brick-work. This brick-work was supported by a cast-iron plate resting on four cast-iron columns. At the beginning, the jacket was lined with air-dried radial bricks, made of crushed quartz and fire-clay, as it was thought that the jacket would not stand the heat on its bare plates. After a short time the practice was altered and no lining mas put in. The jacket was closed at the top and had a steam drum connected by two pipes at the back. This steam drum was connected to the boiler in which the steam was made for driving the Baker blower, the rock breaker and the pumps. The bottom of the jacket mas also connected to the boiler. The jacket was run under boiler pressure (80 Ib.) for some time, but eventually cracks developed in the inner plate between the tuyere holes,

Jan 1, 1913

By Arthur McKee

As HEAT is the controlling factor in all smelting operations, it will be .most helpful to make a new set of calculations on the basis of a .unit of fuel burned at the tuyeres to carbon monoxide. This ties together the only two factors in this operation that seem to be constant with respect to each other-the fuel at the tuyere and the air or its oxygen content. If our usual smelting operations, using natural air heated to reasonably obtainable temperatures, furnish sufficient heat above this critical temperature for the purpose, it is doubtful whether additions of oxygen will be of marked benefit. A unit of fuel will not produce a single heat unit more if burned with pure oxygen than if burned with natural air and less heat will be available per unit of fuel by the amount of heat that is carried in by the preheated nitrogen in the natural air of the blast. This is more readily apparent if considered in connection with a heat balance sheet per unit of fuel at the tuyere. The heat available in the stack, as shown by the committee's report, is less by reason of the lower fuel consumption per unit of output assumed in this calculation. The balance sheet for enriched air shows a shortage of the amount of heat usually carried in with the blast; also a lack in the hearth of sufficient heat to melt the 18 per cent. additional metal and slag and in the shaft to the extent of the shaft heat required to heat the 18 per cent. additional stock to the melting point. These heat deficiencies are provided for by the largely increased conversion of carbon monoxide into carbon dioxide, which is assumed, as shown by the following figures: Calculation for natural air: Carbon dioxide 18.4 per cent. (after having eliminated the carbon dioxide from limestone) and 20.8 per cent. of carbon monoxide. Calculation for oxygen-enriched air: Carbon dioxide 28.4 per -cent. and carbon monoxide 23.2 per cent. (no carbon dioxide from stone as lime is charged instead).

Jan 11, 1924

By C. W. Andrews

The various methods of by-product coke-manufacture have been quite thoroughly discussed in a number of papers recently published, and I think it would possibly be of interest and value to discuss the growth and probable future of the byproduct coke industry, rather than details of manufacture. The first by-product coke-plant in the United States, consisting of 12 ovens, was put in operation at Syracuse in January, 1893. This installation was followed by one at Johnstown, Pa., in 1895; one at Dunbar, in 1896, and one at Glassport, in 1897. The plant at Syracuse was primarily intended to supply the owners with ammonia for their alkali-works. At Glassport, for the first time, gas was sold for illuminating purposes, although it was mixed with water-gas to make it marketable. The New England Coke & Gas Co. started the plant in Boston in 1899, which was destined to change the whole trend of the establishment of by-product plants, since it manufactured for the first time illuminating-gas suitable for sale without enrichment. This was accomplished by dividing the gas on the battery into two portions. One portion, consisting of the richer part of the gas, was saved for sale, while the remaining, or leaner, portion was used in the battery. This idea was originated by Dr. Schniewind, of the United Coke & Gas Co. The coke was used for domestic, industrial, and locomotive fuel, as its sulphur-content was too high to make it suitable for use in the foundry. The successful operation of this plant led to the building of additional plants at points where the production of illuminating-gas could be sold to advantage and where there was a fair market for the coke-output. The following list of illuminating-gas plants in order of construction will give a good idea of the rapid growth of this method of combined gas- and coke-manufacture: Hamilton, Ohio; Detroit, Mich.; Camden, N. J.; Baltimore, Md.; Chester, Pa.; Milwaukee, Wis.; Duluth, Minn.; Geneva, N. Y.; Chicago, Ill.; Indianapolis, Ind. In addition to these there are now under construction plants at Muncie, Ind.; Joliet, Ill., and Waukegan, Ill., all of which will produce illuminating-gas and metallurgical coke.

Jan 1, 1913

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By Walter F. Pond, Kendall E. Born

Production of crude oil in Tennessee during 1935 approximated 20,000 bbl., an increase of about 5000 bbl. over 1934. The total production for the state is an estimate, since the only definite figures available are those for Scott and Morgan counties, where 12,377 bbl. were marketed during 1935, an increase of 4305 bbl. over the preceding year. The oil fields of Scott and Morgan counties are near the eastern margin of the Cumberland Plateau where Pennsylvanian sediments rest uncon-formably upon the Mississippian. Near Glenmary, in Scott County, the production is from the middle Mississippian, probably near the top of the St. Louis limestone. Accumulation is due to a low, east-west anticline which has been cut by a fault. This field is now 20 years old and only a few wells are pumped at present. Oil was Struck along Boone Camp Creek in Morgan County in 1924 and there has been small production since that time. The oil comes from the middle of the Fort Payne formation of lower Mississippian age at a depth of 1400 ft. Geologic work in the area has shown that a terrace and porosity conditions in the Fort Payne formation account for the accumulation. The production figures on a number of small producing wells in Clay and Overton counties are not available. As pointed out by Glenn1, the installation of small local skimming or topping plants in the fields has curtailed the shipment of crude oil out of the state and as a result it has been impossible to secure accurate production figures in these counties. The operators, in most cases, are reluctant to give information, and there is no state law requiring them to do so. Based upon information available to the writers, it is believed that between 7000 and 8000 bbl. is a fair estimate of the production in Clay and Overton counties during 1935. More than 500 wells have been drilled in Clay County, the majority of which were drilled east of Cumberland River. Some eight small oil fields have been developed in the county within the past 12 years, a

Jan 1, 1936

By M. Gensamer

IT has been suggested by a number of people that it would be worth while for some one to attempt to summarize or condense the proceedings of this symposium. This task has fallen to me as organizer and co-chairman. Its difficulty will be appreciated by anyone who attempts to read the whole proceedings. It is therefore with trepidation that I offer the following digest. In recent years there has been a renewal of interest in America on this subject of the cohesive strength of materials, and a growing appreciation of the need for a better theory of cohesion failure. The theories of elastic action and plastic action are well developed, particularly the former. The theory of plastic action is still in the course of development, but it is well along. Plastic action is terminated by cohesion failure and what is needed is a theory that will tell us when to expect the cohesion failure. In the past it has generally been assumed that cohesion failure will occur when a critical value of the maximum tensile stress has been reached. Many experiments have shown that this is not strictly true, and this symposium concerns itself with the failures of this simple hypothesis, and with the efforts that have been made to devise a more satisfactory theory. The most active contributor in recent years to knowledge in this field is Dr. McAdam, and he was asked to open the symposium with a summary or condensation of his papers and views. Undoubtedly it is presumptuous to attempt a still greater condensation, but perhaps it will be useful, because even his contribution to this symposium contains no summary, no concise statement of just what his contribution has bees. Dr. McAdam makes two main points. The first is that the cohesive strength is not a single valued quantity, but that it is a function of all three principal stresses and hence must be represented diagrammatically by a surface in a three-dimensional figure. Dr. McAdam has attempted so to delineate the cohesion limit, basing his

Jan 1, 1944

By Amos L. Beaty

The oil industry can prosper only if crude production is not excessive. This is true for several reasons. In the first place, the marketing branch of the business is so highly competitive that there is little room for profits in it. There are too many service stations, too many middle men or jobbers, too many refiners eager to press their products upon the market. And the battle is between the strong. If any money is being made in oil today it is by small marketers who buy products from the refining companies and sell on guaranteed margins. In the second place, refineries are overbuilt. There is a large surplus refining capacity. If refined stocks were drawn down they could and would be replenished in short time on short notice. This excessive refining capacity is not serious, however, if the supply of crude is limited to trade requirements. True, it may reflect upon the intelligence of the industry, but if there were a shortage of crude for a few years refining capacities would be readjusted. In the meantime no great harm could result from some idle capacity. It requires no computation to see that refiners could not produce surplus stocks of products from a short supply of crude. I have in mind, of course, the increased yields from cracking. Allowance must be made for that. Still, the picture is the same; less crude is required. I think we can have prosperity in the oil business if too much crude is not produced. A proper limit at this point would be felt all the way down the line. It would slow the refiner and slow the marketer inevitably. Once this constant pressure to make more and sell more is off, operations will be normal and there will be some return on investments. Peices in Relation to Production Potential production at this time is very large, and this condition has existed for many months. As a result the price of crude is low. It is below the average cost of production. Nevertheless, if restraints were withdrawn actual production would immediately increase and the situation would become even worse than it is now. Eventually, of course, the

Jan 1, 1932

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

By M. Gensamer

It has been suggested by a number of people that it would be worth while for some one to attempt to summarize or condense the proceedings of this symposium. This task has fallen to me as organizer and co-chairman. Its difficulty will be appreciated by anyone who attempts to read the whole proceedings. It is therefore with trepidation that I offer the following digest. In recent years there has been a renewal of interest in America on this subject of the cohesive strength of materials, and a growing appreciation of the need for a better theory of cohesion failure. The theories of elastic action and plastic action are well developed, particularly the former. The theory of plastic action is still in the course of development, but it is well along. Plastic action is terminated by cohesion failure and what is needed is a theory that will tell us when to expect the cohesion failure. In the past it has generally been assumed that cohesion failure will occur when a critical value of the maximum tensile stress has been reached. Many experiments have shown that this is not strictly true, and this symposium concerns itself with the failures of this simple hypothesis, and with the efforts that have been made to devise a more satisfactory theory. The most active contributor in recent years to knowledge in this field is Dr. McAdam, and he was asked to open the symposium with a summary or condensation of his papers and views. Undoubtedly it is presumptuous to attempt a still greater condensation, but perhaps it will be useful, because even his contribution to this symposium contains no summary, no concise statement of just what his contribution has been. Dr. McAdam makes two main points The first is that the cohesive strength is not a single valued quantity, but that it is a function of all three principal stresses and hence must be represented diagrammati-cally by a surface in a three-dimensional figure, Dr. McAdam has attempted so to delineate the cohesion limit, basing his

Jan 1, 1945

By Kendall E. Born, Walter F. Pond

Production of crude oil in Tennessee during 1935 approximated 20,000 bbl., an increase of about 5000 bbl. over 1934. The total production for the state is an estimate, since the only definite figures available are those for Scott and Morgan counties, where 12,377 bbl. were marketed during 1935, an increase of 4305 bbl. over the preceding year. The oil fields of Scott and Morgan counties are near the eastern margin of the Cumberland Plateau where Pennsylvanian sediments rest uncon-formably upon the Mississippian. Near Glenmary, in Scott County, the production is from the middle Mississippian, probably near the top of the St. Louis limestone. Accumulation is due to a low, east-west anticline which has been cut by a fault. This field is now 20 years old and only a few wells are pumped at present. Oil was Struck along Boone Camp Creek in Morgan County in 1924 and there has been small production since that time. The oil comes from the middle of the Fort Payne formation of lower Mississippian age at a depth of 1400 ft. Geologic work in the area has shown that a terrace and porosity conditions in the Fort Payne formation account for the accumulation. The production figures on a number of small producing wells in Clay and Overton counties are not available. As pointed out by Glenn1, the installation of small local skimming or topping plants in the fields has curtailed the shipment of crude oil out of the state and as a result it has been impossible to secure accurate production figures in these counties. The operators, in most cases, are reluctant to give information, and there is no state law requiring them to do so. Based upon information available to the writers, it is believed that between 7000 and 8000 bbl. is a fair estimate of the production in Clay and Overton counties during 1935. More than 500 wells have been drilled in Clay County, the majority of which were drilled east of Cumberland River. Some eight small oil fields have been developed in the county within the past 12 years, a

Jan 1, 1936

By J. W. Eckerd

Anthracite mining developments have not been as spectacular as the advances made for bituminous coal. The reasons are well known, i.e., steeply pitching seams of the western, eastern, middle and southern fields, and the physical conditions of the strata in which the seams are situated. Beds with moderate pitches (30º to 35º or less) have been mined with coal planers, longwall with movable props, shaker chutes, coal borers and large diameter boring machines. However, the use of this equipment has been limited to a relatively small portion of the production. Long-hole drilling has been developed from a point where holes of 25 or 30 ft have been replaced by those up to 130 ft. This has been possible through the introduction of primacord and similar detonating agents that can fire a long train of explosives with one cap. The usual practice in long-hole mining is to drive a gangway, chutes and monkey heading, or return airway, in the normal development manner. Two breasts can then be driven from the lower to the upper level to act as openings for the beginning of the long-hole work. Following completion of the development, holes can then be drilled from the monkey headings 100 ft or more up the pitch through the coal to within 15 ft or more of the upper level, depending on the nature of the coal on the roof. The thickness of the coal bed determines the spacing of the long holes, although they usually are on 6-ft centers for a 6-ft thick coal seam. The Bureau of Mines has conducted extensive investigations and tests on the development of a hydraulic mining system to be used in conjunction with hydraulic hoisting. Tests were conducted in cooperation with a large anthracite producer in a coal seam from 10 ft 6 in. to 15 ft in thickness and on a pitch from 0º to 20. This particular mining procedure is adaptable only to thick seams on relatively flat pitch as the maneuverability of the hydraulic jumbo is an important restricting factor.

Jan 2, 1968

By D. P. Mitchell

Western Australia is the home of much that is new and interesting in the gold-mining industry. Some of the gold deposits are outranked for size and value by nothing yet discorered, while the value of the ores is, in many cases, rivaled only by their complex character. As in all parts of the world, many of the ore-bodies occur in ways which tax the skill of the miner in following them; and among these the writer considers the case of the East Murchison United more interesting than the average. This is one of the leading gold-mines of the colony in point of production, and is situated near the town of Lawlers, in the East Murchison district. The country for several miles around the mine is mainly granite, and the line of outcrop on which this mine is located can be traced for a long distance. As will be seen from the accompanying plan (Fig. I), there are, at the water-level, two nearly parallel veins running slightly north of west. Structural Features.—The most striking peculiarity of these veins, and the hardest to understand, is their tendency to send out horizontal stringers or side-veins. These vary in size from a veinlet an inch thick to a veil] several feet in width, and they extend with great persistence into the wall-rock on either side of the vein. This tendency is shown in Figs. 2 and 3. The usual signs of a movement of the wall-rocks, such as a ribbon-structure of the quartz and a well-defined gouge or seam of clay along the walls, are in many places lacking, while in other places they appear strongly marked. They seem more in evidence below water-level than above. It is a commonlly accepted idea that when a gold-bearing vein loses in width, it often gains in value. In this instance, however, the direct opposite is the case; for in many stopes it has been possible to leave the narrow portions of the vein to act as pillars, and to extract only the wide portions, which are

Jan 1, 1900

By Joseph Richards

THERE are two essentially different types of case-hardening processes; that using a dry mixture in which the object to be case-hardened is packed and kept for the necessary time at the necessary temperature, and the "liquid" process, employing a bath of fused, salts into which the object- is immersed and which by immediate contact case-hardens the surface of the article. The Shimer process belongs to the second class, and was a war emergency invention. Of the liquid melts used as baths, the most effective and most fre¬quently used are melted potassium cyanide and melted sodium cyanide. These may be used either pure, or mixed with salts that reduce the melting point and the percentage of cyanide present. The use of these baths since 1914 has met many commercial difficulties because of the high price and frequent commercial scarcity of the cyanide salts; at present sodium cyanide has practically entirely displaced potassium cyanide. Another trouble is the danger to the workmen handling the cyanide salts, which are extremely poisonous, and the annoying and poisonous vapors or gases given off in the workshop, unless an effective system of hoods and ventilation is provided, so as to prevent the gases from the baths mixing with the air of the room. Porter W. Shimer, of Easton, Pa., has invented a substitute for the bath of melted cyanides which case-hardens with equal or greater facility and effectiveness, gives off no poisonous vapors, and costs for chemicals materially less than the cyanide costs in the previously used baths. The process has been in use over a year in a large American works and the following statement embodies the results of practical experience in the use and operation of the process. The Shinier liquid or melted bath consists of a mixture of easily fusible salts that do not possess case-hardening properties, into which is immersed fresh calcium cyanamide, which imparts to the bath case-hardening properties. The composition of the non-case-hardening-,salts appears rather immaterial. Good results have been obtained by using a mixture of sodium chloride, calcium chloride, and barium chloride in

Jan 2, 1919

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By Theo B. Comstock

In the summer of 1877, the writer led a party of four young men from Cleveland, Ohio, by way of the Great Lakes, to Prince Arthur's Landing (now Port Arthur), at the northwest corner of Lake Superior, thence, via the Dawson route and side journeys, as far as Cross Lake. It was the original intention to pass down the Pigeon river to its mouth, but the loss of one member of the party for six days in the forest, added to other obstacles, made it necessary to turn back. A well-filled note-book, together with illustrative collections, were sunk beyond recovery at the head of the Maligne rapids by the breaking of a tow-line, and two of our number (including myself) narrowly escaped drowning. I had, probably, obtained information of considerable economic value, but the necessity of travelling nearly 125 miles for provisions (excepting a meagre supply kindly furnished us by a Canadian government gang whom we fortunately met), rendered further note-taking impossible. Until now, such results of this expedition as could be recorded . from memory have gone unpublished, because of my inability to make them serve any useful purpose. The trip of the Institute to Vermilion Lake, only a few miles south and east of our turning point, gives some little excuse for presenting the following lines at this time. The ridge back of Port Arthur, Ontario, which follows approximately the course of the Lake Superior shore line, brings up the slates and accompanying strata through which the silver and gold veins of that region have penetrated. The interior district, hack from the lake, may be briefly described as a glaciated area, having its general drainage less modified by erosion than by the original structure. This statement, however, must be somewhat qualified with reference to minor details, which all bear the unmistakable impress of the ice-flow and its recession. In many respects there is much in this tract to remind one of the Sault Ste. Marie topography, excepting that the granitic character of the rocks is here largely replaced by fissile strata. The Kaministiquia river cuts through several of the parallel folds,

Jan 1, 1888

By R. E. Collins, Paul B. Crawford

Mathematical equations have been derived to show the effect of the slippage phenomomenon (Klinkenberg effect) on unsteady-state gas flow through porous media. The assumption is made that the slippage may be represented by an equation of the type It is pointed out that most of the existing data on unsteady gas flow may be corrected for slippage by a simple change in definition of the dimen-sionless groups. INTRODUCTION Several solutions to the various problems associated with the unsteady-state flow of gas through porous media have been recently presented in the literature.','" The cited publications have resented solutions for flow under ideal conditjons. The principal assumptions involved include: (a) the density of the gas obeys the perfect gas law; (b) the viscosity of the gas is constant; and (c) the gas permeability is constant. Few, if any, actual gases under reservoir conditions are believed to conform with the above, but the ideal solutions do provide the basis for making improved estimates on the performance of gas reservoirs. The purpose of this paper is to show the performance characteristics when assumption (c) is corrected for the slippage phenomenon or the Klinkenberg effect. This is believed to be a step nearer to reality. MATHEMATICAL DEVELOPMENT Case 1. Gas Flow — Ideal Conditions The equations describing the flow of gas under ideal conditions have been clearly presented in the cited literature; however, for completeness of this work they are repeated here. The basic differential equation describing the flow of gas is Equation (6). It may be derived as follows: The continuity equation, the perfect gas law and Darcy's law are combined to give: Manuscript received in the Petroleum Branch office Aug. 3, 1963 or If — is constant, Equation (5) is rewritten to form the basic Equation (6). or for the linear case A dimensionless equation is obtained by dividing through by (pl)z and making the substitutions shown below: The resulting equation is A similar procedure for the radial case leads to the following equations: where and Equations (11), (12), and (13) are those used by Bruce, et al., and Jenkins and Aronofsky for their computational work.

Jan 1, 1953

By Horace F. Silliman, Curtis L. Wilson, Eugene C. Little

The change in electrical resistance and Rockwell hardness (16-100-B) of copper alloys containing Ni2Si and Co2Si was determined by annealing the quenched solid solutions at various temperatures for various lengths of time. The rate of precipitation of Nisi, as measured by the rate of decrease of electrical resistance and increase of hardness, increased with annealing temperature up to a certain point, depending on the percentage of Ni2Si present. At these temperatures discontinuities in the rate: change occurred. Similar discontinuities in the Co2Si alloys were no The solubility of Co2Si in copper was found to be 5 per cent at 970" DISCUSSION (Robert F. Mehl presiding) R. I?. Mehl, Pittsburgh, Pa. (written discussion).—The electrical conductivity and hardness curves reported in this paper are interesting, particularly because many of the anomalies of the precipitation processes are evident from such curves. The title of the paper, however, is deceptive, for it implies that measurements of electrical conductivity and hardness are suitable to determine the rate of precipitation. Neither of these methods is suitable for a quantitative measurement of rates of reaction or of precipitation in the solid state. Electrical conductivity in some alloys shows an anomalous increase during the first stages of aging at low temperatures; it is notably sensitive to strain and to state of subdivision. I have plotted the conductivity curve representing the decomposition of the phase at 555" C. in the copper-aluminum system, given in the paper by Smith and Lindlief (Fig. 47, p. 93) as a rate of reaction curve, and compared it with the curve determined by area evaluation (Fig. 7); these two curves are not coincident. Hardness is likewise very uncertain, for it is so much dependent upon particle size. Of the various methods proposed for the study of rates of reaction and precipitation, the evaluation of volume of reaction product from the respective area of matrix and reaction product on the photomicrograph is the most trustworthy; suffering, perhaps, only from low sensitivity during the early stages. This method, used originally by Davenport and Bain and now by Smith and Lindlief, is suitable for

Jan 1, 1933

By R. S. Shrode

By now most readers of this column are aware that it no longer has a regular editor. Tom Murphy, who did the job so well, has had to bow out because of his duties in Australia---duties that keep him from the luxuries of such things as typists and typewriters for rather extended periods of time. We will miss his regular contributions but hope and expect to hear from him as a guest columnist from time to time. Finding an editor to function on a regular basis turns out to be no simple task. This does not mean that there may not be candidates around who would secretly enjoy having their arm twisted into a "yes" position, but at the moment none has been found. Anyway, at the Salt Lake City business meeting it was agreed that we should try to spread the load around. To that end, the Regional Vice Chairmen were specifically singled out as one potential source of contributions. These fellows should have an opportunity for a hearing during their term in office. The existing organizational set-up of the IndMD Division may be a little unfair to this group of officers. The limited responsibility outlined in our Manual of Official Duties and Responsibilities does not offer them much chance for self-expression. Probably the by-laws were written so as to have a geographic representation of membership in case it should be needed at some time. But that is another subject. The point is that now these regional officers have an opportunity to speak out on topics of their own choosing through this column. Some have already done just that. There are also other potential contributors to the column. One is the Secretary, who twice a year uses the column for distributing the minutes of our business meeting to the members. Another is the outgoing Division Chairman. In Salt Lake City, it was decided that this officer should be challenged to contribute something each year as a means of reviewing events of the past year or explaining what should have happened but didn't. I am, therefore, trying to accept that challenge.

Jan 1, 1970