Search Documents

By W. A. Backofen, D. Lee

Titanium of commercial purity (RC-70) and two all-a (hcp) alloys (4Al-1/4O2 and 5Al-2.5Sn) were tested in sheet form under conditions of combined-stress loading. Plane-strain compression and plane -strain tension together with uniaxial compression and tension provided information for constructing the tension-tension and compression-compression quadvants of the plane-stress yield locus. Coordinate values were obtained from yield-strength measurements; the slope at each point was based on a plastic-strain ratio. The materials represented a wide range of plastic anisotropy, which was reflected in correspondingly varied departures of the yield locus from that for iso-tropy. The tension-tension and compression-compression quadrants were not identical. If the uniaxial yield strength is insensitive to direction and the sign of the applied stress, the Mises or perhaps the Tresca criterion is adequate for predicting the onset of yielding under combined-stress loading. The prediction is not so straightforward in plastically anisotropic material. Depending upon details of texture, combined-stress yielding resistance may be substantially different from that indicated by the usual criteria.' However. a continuum theory of yielding under such conditions is available for reasonably direct application.2,3 Whether or not it can be used successfully must, of course, depend upon how closely the conditions of the theory are satisfied in the material in question. In its present form the theory contains no provision for Bauschinger-type effects, nor does it allow for the consequences that might grow out of deformation by more than one mechanism, e.g., by slip and twinning.4 With those limitations, more importance must be attached to experimental information about the yield surface for anisotropic materials. Studies of the yield surface have generally been confined to states of plane stress (tension-tension and tension-compression) established in thin-wall tubes by externally applied forces and internal pressure. That approach would be entirely suitable for anisotropic materials if they were available in tube form or in sufficient bulk to be machined into test specimens. 6-9 It would not serve for the textured and anisotropic sheets of much current engineering interest, unless sheet could be formed into high-pressure tubing without structural change. Since there would seem to be little chance of the latter, practical alternatives are needed. One such alternative is the subject of this paper. It involves the use of a few selected but relatively simple uniaxial loading tests on sheet specimens. The underlying idea is presented here with some details relating to application and a few results bearing on how well it has worked. THE BASIS OF TESTING Conventional Measurements. Yielding for a general case of anisotropy is described by the plane-stress locus in Fig. 1. Reference directions in the sheet specimen are related to the stress coordinates as shown with the insert: x is the rolling direction, y the transverse direction, and z the through-thickness direction. The four reference-direction yield strengths (t, tension; c, compression), Xt, Xc, Yt, and Yc, are all different. Nine paths that can be followed in uniaxial loading experiments are identified. Paths 1, 2, 3, and 4 represent conventional tension and compression testing to establish Xt, Yt,.Xc, and Yc. Useful information also comes from the ratio of the transverse plastic-strain components associated with yielding and flow in conventional tension or compression. A condition to be satisfied in locus construction is that the plastic-strain vector be everywhere normal to the locus.10 The projection of the vector which would

Jan 1, 1967

By C. S. Land

Relative permeability functions are developed for both two- and three-phase systems with the saturation changes in the imbibition direction. An empirical relation between residual nonwetting-phase saturation after water imbibition and initial nonwetting-phase saturations is found from published data. From this empirical relation, expressions are obtained for trapped and mobile nonwetting-phase saturations which are used in connection with established theory relating relative permeability to pore-size distribution. The resulting equations yield relative permeability as a function of saturation having characteristics believed to be representative of real systems. The relative permeability of water - wet rocks for both two- and three - phase systems, with the saturation change in the imbibition direction, may be obtained by this method after properly selecting two rock properties: the residual nonwetting-phase saturation after the complete imbibition cycle, and the capillary pressure curve. INTRODUCTION Relative permeability is a function of saturation history as well as of saturation. This fact was first pointed out for two-phase flow by Geffen et al. 1 and by Osaba et a1.2 Hysteresis in the relative permeability-saturation relation also has been reported for three-phase systems.3 Since saturations may change simultaneously in two directions in a three-phase system, four possible relationships arise between relative permeability and saturation for a water-wet system. The four saturation histories of this system were given by snel14 as 11, ID, DI and DD. I and D refer to the direction of saturation change (imbibition and drainage), with the first letter of the symbol indicating the direction of change of the water phase. As used in this paper, the second letter of the symbol refers to the direction of saturation change of the gas phase, i.e., D and I indicate an increase and decrease, respectively, in gas saturation. Only a few three-phase relative permeability curves have been published. Leverett and Lewis5 published three-phase curves for unconsolidated sand, and Snell4 reported results of several English authors for both drairrage and imbibition three-phase relative permeability of unconsolidated sands. Three-phase relative permeability curves for a consolidated sand were published by Caudle et a1.3 for increasing water and gas saturations (ID). Corey et a1.6 reported drainage (DD) three-phase relative permeability for consolidated sands. Recently, Donaldson and Dean7 and Sarem8 calculated three-phase relative permeability curves from displacement data on consolidated sands, also for saturation changes in the drainage direction. The only published three-phase relative permeability curves for consolidated sands with saturation changes in the imbibition direction (11) are those of Naar and Wygal.9 These curves are based on a theoretical study of the model of Wyllie and Gardner 10 as modified by Naar and Henderson.11 Interest in three-phase relative permeability has increased recently due to the introduction of new recovery methods and refinements in calculation procedures brought about by the use of large-scale digital computers. The scarcity of empirical relations for three-phase flow, and the experimental difficulty encountered in obtaining such data, have made the theoretical approach to this problem attractive. RELATIVE PERMEABILITY AS A FUNCTION OF PORE-SIZE DISTRIBUTION Purcell used pore sizes obtained from mercury-injection capillary pressure data to calculate the permeability of porous solids.12 Burdine extended the theory by developing a relative permeability-pore size distribution relation containing the correct tortuosity term.13 The works of Purcell and Burdine were combined by Corey14 into a form that has

Jan 1, 1969

By J. E. 214-000-000-010 Warren, M. R. J. Wyllie, T. Meidav, L. Scharon, R. Uhley, A. J. deWitte

By considering the stoichiometry of the underground combustion process, an equrztion was derived relating the point velocity of the combustion front as a function of the air flux, fuel content, efficiency' of oxygen uitilization, hydrogen:carbon ratio, and ratio of carbon dioxide In carbon monoxide produced. In addition, an equation for cnlcrllating the amount of injected air necessary 10 produce the oil from I Cu. ft of reservoir space was derived. This equation has a direct bearing on evaluating compression costs for the process. Values calculated from these equations are in good agreement with experimentnlly obscrvcd values obtained from laborator) tube runs reported in the literature. The equations are also u\eful for atlcrlyzinf: experinlental data for inconsistencie.r.. I NTRODUCTION The injection of energy in the form of heat into an oil-bearing formation as a means of increasing the recovery of oil has been the subject of much discussion and experimentation as far back as 1920. The ideas have ranged from the injection of steam to the direct use of electricity as a means of getting thermal energy into a formation. However, most laboratory and field studies have been confined to the process whereby a portion of the crude in the reservoir is burned to generate the necessary heat to increase the mobility of the oil by reducing its viscosity. A recent paper by W. L. Martin, et al.', described the results of a number of laboratory experiments in which the combustion process was studied in a sandpack. Studies such as this indicate that with the temperatures involved, the oil is partially coked in this process and it is this coke which provides the fuel for combustion. The combustion of this residual coke can be analyzed theoretically by applying simple stoich-iometric principles to the combustion process. It is the purpose of this paper to compare the results reported in these experiments with those obtained from theoretical considerations. The variables studied by Martin, et al, among others, include combustion front velocity, air flux, oxygen utilization, fuel concentration, ratio of carbon dioxide and carbon monoxide in combustion gases, and the hydrogen:carbon ratio of the residual fuel. All these variables come into consideration when the stoichiometry of the combustion process is studied. The experimental conditions and results are tabulated in Tables 3 and 4 of Ref. 1. For purposes of comparison with calculated results, it was necessary to change the units of a number of the variables. UNDERGROUND COMBUSTION STOICHIOMETRY The combustion or oxidation of the carbonaceous residue or "coke" on the sand can be described in terms of the equation: where n is atomic ratio of hydrogen to carbon, m is ratio of moles of CO2 to CO produced, and CH. is taken as the unit molecular weight, realizing that actually the coke has a large range of high molecular weights. Assuming that all the fuel laid down in the sand is burned, the ratio of moles of oxygen consumed to moles of coke can be written as follows. Moles 0MolesMolescoke In terms of moles O2 per pound of coke, where 12 + n is the molecular weight in pounds per mole. If the 0, consumed is measured in standard cubic feet (60°F and 1 atm) and the coke in pounds per cubic foot of formation, 2, then:

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By J. H. Brophy

Experimental evidence in recent years shows that nickel coated hydrogen reduced tungsten powder can be sintered to 98 pct of theoretical density at 1100°C. New data indicate that the sintering rate is the same for nickel contents ranging from 0.125 wt pct (mon-atomic layer) to 5.0 wt pct Ni coated on 0.561. tungsten powder. Nickel tungsten made by coreduction from oxides sinters in a kinetically similar way, but the rate tends to increase with higher nickel contents. The activation of sintering can be accomplished with a minimum amount of nickel if coated powder is used. Transverse rmpture strength was found to increase in specimens containing 0.25 pct Ni as density increased during the initial stage of the carrier-phase sintering process. Upon the onset of grain growth in the final stage, strength was found to decrease. With increasing nickel contents up to 4 pct, strength increased. Maximum strengths in three-point loading were observed at 73,000 psi for 0.25 pct Ni and 93,000 psi for 5 pct Ni. These were comparable to that of massive tungsten recrystal-lized in the presence of nickel and tested in the same way. The results were sensitive to the mode of powder treatment and ductility was negligible in all cases. The study and application of sintered bodies of nickel and tungsten is not new; however, the analysis of the mechanism by which small additions of nickel increase the sintering rate of tungsten promises to Contribute new information regarding sintering theory in general. Initial experimental evidence was presented by the authors showing that nickel-coated hydrogen-reduced tungsten powder may be sintered to 98 pct of theoretical density at 1100°C in 16 hr.' Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the 'solution-precipitationo step postulated when the carrier phase is liquid3 although in the nickel tungsten case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in mi-crostructures at the temperatures under consideration. In the present work, new data for nickel-coated tungsten powder are offered in support of the proposed mechanism, and a more explicit study of the second stage of densification is presented. Concurrently, the sintering kinetics of these coated powders are compared to Ni-W powder made by coreduction of oxides. In this way the present work can be compared to earlier results in nickel activated sintering of tungsten in which the coreduction process was emplyed. The ultimate utility of such an activated sintering process will be determined to some extent by the mechanical and physical properties of the final prod-

Jan 1, 1962

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By Walter E. Duncan

THE ores treated at the concentrating plant largely come from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately intergrown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead concentrates, (2) zinc concentrates, (3) acid-grade fluorspar concentrates and (4) metallurgical-grade fluorspar concentrates.2,3 Although fluorspar had been floated in Canada in 1921 4 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; such as, for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1946

By R. S. Busk, E. G. Bobalek

THE relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.1,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittlement of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.3 To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Recently it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate microporosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.1 Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H2, solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice .2 For true equilibrium values of solubility, therefore, the pressure at the metal surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1946

By Donald W. Scott

Generally speaking, there is nothing very difficult about taking good microgrztphs of photogenic thin sections or grains with a petrographic microscope-camera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. Ia) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. Ib) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this' is an incorrect interpretation is evident by reexamining the micrograph of Fig. Ia. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. Ic the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1949

By G. W. Nabor, M. Mortada

The effects of anisotropic or directional permeability on the areal sweep efficiency and the flow capacity are examined. The paper points out the importance of taking directional permeability into consideration in planning a flood. It analyzes the two-dimensional flow pattern associated with the skewed line drive for a unit mobility ratio. The direct and staggered line drives are treated as special cases of the skewed line drive. Analytical expressions are developed for the areal sweep efficiency at breakthrough and the flow capacity. They are related to the spacing between like wells, the distance between a row of injectors and the nearest row of producers, and the degree of skewness of the line drive. The latter quantity is defined such that it is equal to zero for the direct line drive and equals one-half for the staggered line drive. The areal sweep efficiency and the flow capacity depend also on the orientation of the flood pattern with respect to the principal axis of anisotropy. The paper provides a simple method for determining the areal sweep efficiency and the flow capacity for a formation in which the permeability in the bedding plane is anisotropic. INTRODUCTION Directional or anisotropic permeability is manifested by the ability of the formation to conduct fluids more readily along certain preferred directions. This situation occurs in many producing formationsl-4 and is usually attributed to depositional features in which the sand grains are oriented in a preferred direction. In some cases it results from the formation of a major and a minor fracture system. 4 Directional permeability should be taken into account in many phases of the production and exploration activities. Recognizing its existence in the formation of interest and planning accordingly can lead to increased recovery and substantial savings. For instance, the areal sweep efficiency in a water flood depends to a great extent on the orientation of the flood pattern with respect to the principal axis of permeability. Anisotropic5 permeability is specified by the directions of its three principal axes and the permeability along each axis. The principal axes of permeability are mutually perpendicular. This paper deals with the areal sweep efficiency at breakthrough and the flow capacity for formations with aniscltropic permeability. The flood pattern considered consists of alternate rows of injecting and producing wells. The rows of wells are parallel and form a developed, skewed line drive which is illustrated in Fig. 1. The staggered and direct line drives are treated as special cases of the skewed line drive. PRELLMINARY CONSIDERATIONS The formations considered in this paper are assumed to be of uniform thickness and porosity. The permeability is uniformly anisotropic, with each principal axis of permeability maintaining

By S. Usui, I. Iwasaki

The adsorption mechanism of dodecylammonium acetate (DAA) on mercury in potassium fluoride solutions at natural, near neutral pH was investigated. Difler-ential capacity combined with electrocapillary measurements on a dropping mercury electrode were found to provide a sensitive and reliable approach. A shift in the electro capillary maximum (or the point-of-zero-charge) towards positive polarization of the surface due to the adsorption of amine indicated a specific affinity of dodecylammonium ion for mercury surfaces. The amine was shown to adsorb competitively with potassium ion on mercury. Through correlation of the adsorption density of the amine, calculated from the thermodynamic analyses of the electrocapillary curves, and of the diflerential capacity curves, the adsorbed state and the orientation of the amine at the interface were considered. The similarities and the differences in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide were evaluated. With the promise of flotation providing a cheap and large-scale process for the upgrading of low-grade ores and magnetic concentrates, the iron ore industry has made a sustained search over the years for a flotation reagent of general applicability and high selectivity. Having shelves full of commercial reagents already on hand and anticipating more, both the users and the suppliers are in need of an experimental approach sensitive enough to differentiate the individual characteristics in each group of reagents. Therefore, the adsorption behavior of various flotation reagents on mineral surfaces from aqueous solutions has been a subject of much investigation. The current view of adsorption based on the electrical double-layer theory is formulated on the assumption that certain ions in solution act as potential-determining ions. Their concentrations fix the potential drop across the double layer and their adsorptions govern the surface charge.' Two methods used to study the adsorption

Jan 1, 1971

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.' In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer's early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer's direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By Harold Rose

THE peak of production from the Appalachian natural gas field was apparently reached about 10 years ago, and the annual production from Pennsylvania, West. Virginia and Ohio has now dropped to about two-thirds of the amounts obtained in 1916-and 1917. This falling off in production has occurred in spite of vigorous efforts and large expenditures by producing companies to maintain or increase their output. The greatly increased costs of development and handling are reflected in the present average value of natural gas at the point of consumption, which value in the three states referred to, has more than doubled in the past 10 years. While it is true that the natural gas production of the United States has increased during recent years, this increase has come from southwestern states, particularly from Oklahoma, California, Louisiana and Texas, which states are now leaders in the production of this valuable but fleeting resource. Pennsylvania, originally the leading state in natural gas production, occupies sixth place in the latest (1924) U. S. Bureau of Mines statistics. West Virginia, which held first place for 15 years, has dropped to third rank, and Ohio is the seventh state in the order of natural gas production. Domestic and industrial demands for gas are constantly increasing everywhere in the United States. These growing demands have accentuated the difficulties in the localities with depleted natural gas supplies, and serious shortages have already occurred during winter months in the Pittsburgh district. Some relief has been obtained by placing restrictions on the industrial use of natural gas, and by, increasing the price (which tends to reduce consumption). Yet these are but temporary expedients for checking gas consumption, which fail to solve the problem of adequate future supplies of gas.

Jan 10, 1926

By P. LaRochelle, K. Y. Lo, A. L. Tamuly Phukan

In many civil or mining engineering works, the stresses and deformations of natural or excavated slopes due to the combined effect of self-weight and initial stresses are of interest. Because of the mathematical complexities of this problem, however, no complete exact solution exists for the simplest case, that of assuming the stress-strain relation of the rock to be perfectly elastic. Efforts have therefore been directed toward numerical and experimental technique. The stresses within an elastic slope have been obtained by LaRochelle,1 using the photoelastic and finite difference method to determine the difference and sum of principal stresses. Subsequently, Finn,2 Hoyaux and Ladanyi,3 and Duncan and Dunlop4 attempted to solve the same problem by using the finite element method. The problem was also investigated by Brown and Goodman5 and Brown and King6 who emphasize the importance of the effect of loading or unloading procedure on the stress distribution within the slope. Although the geometry of the slope and the boundary conditions involved are identical or similar, the results obtained by these various authors by no means agree. It is therefore necessary to review briefly the results of elastic analysis in order to lend credence to the methods used in the solution. Although the stress-strain behavior of some rocks may be reasonably approximated by the elastic modrl, other rocks generally exhibit an elasto-plastic behavior with strain hardening or strain softening as shown in Fig. 1. Experiments show that for most rocks, the stress-strain relationship is approximately linear from the origin to the point P (neglecting the small concave region under low stresses). At P, the curve deviates

Jan 1, 1970

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.' The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago' for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles'" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2' *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest 'purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.'." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952