Search Documents

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By C. S. Finney, John Mitchell

On December 31, 1959, there existed in the United States 15,993 slot-type coke ovens capable of producing 81,447,700 net tons of coke. These ovens were concentrated in 74 coke plants in 21 different states. As of the same date, there were 7448 beehive ovens in existence at 45 plants in the states of Pennsylvania, Virginia, West Virginia, and Kentucky. Total annual capacity of the existing beehive ovens was 4,368,800 net tons, but only 5148 ovens with a capacity of 3,131,600 tons were in operating condition. It is interesting to compare the average dimensions of slot-type ovens built during recent years with the 30 ft x 5 ½ ft x 16 ½ in. ovens erected at Syracuse, N. Y. in 1892. A composite oven built according to the average dimensions of all those erected between 1954 and 1958, for instance, would be 39 ft long. 12 ft high, and 18 in. in width. The coal capacity would be 16 tons as against the 4.4 tons which could be charged to the Syracuse ovens. Of the 15.993 slot- type ovens in existence at the end of 1959, by far the greater number were built by the Koppers Co. whose total of 11,280 ovens included 7891 Koppers- Becker and 3389 Koppers ovens. Of the remainder, there were 3260 Wilputte, 1350 Semet-Solvay, 63 Otto, and 40 Simon Carves ovens. By-product coke oven plants are usually classified either as furnace or merchant plants. According to the definitions used by the US Bureau of Mines, the former are "those that are owned by or financially affiliated with iron and steel companies whose main business is producing coke for use in their own blast furnaces. All other coke plants are classified as merchant. They include those that manufacture metallurgical, industrial, and residential heating grades of coke for sale on the open market; coke plants associated with chemical companies or gas utilities; and those affiliated with local iron works, where only a small part (less than 50 pct of their output) is used in affiliated blast furnaces." The annual coke capacity of the merchant plants during 1959 was 10,393,000 tons. However, the by-product oven of today is essentially an appurtenance of the iron and steel industry, rather more than 87 pct of total by- product coking capacity being concentrated at furnace plants. This was not always so. There was a time when the merchant plants played a much greater part in meeting the US demand for coke and gas. High noon for the merchant plants was reached during the early 1930's. By 1932 there were as many by- product oven installations being operated by the merchant sector of the industry as by the coke divisions of the iron and steel industry (44 of each), and in the same year the merchant plants produced 46.5 pct of all by-product coke made in the country. Since that time their contribution has drastically declined. In 1940 merchant plants were responsible for only 23.2 pct of total US production, and by 1950 their number had decreased to 30 plants which turned out 18.5 pct of the total by-product coke made. At the end of 1959 only 20 of the 74 existing by-product oven installations were merchant plants. They ac- counted for 12.5 pct of the year's production, or 6,849,786 net tons. This percentage has remained fairly constant since 1954. There are several reasons for the decline of the merchant coking industry. For example. On the grounds of economy, quality control, continuity of supply, and so on, the iron and steel industry usually prefers to control its own mines and carbonize its own coal at or near to the blast furnace rather than rely on independent operators for metallurgical coke. As the steel companies have enlarged their own coking facilities, so has the need for coke obtained from other sources declined. Furthermore, not only has the steel industry increased in self-sufficiency by building mare coke ovens during recent years, but it has also progressively improved the fuel efficiency of its blast furnaces. During the years 1947-49 the average coke consumption per ton of pig iron was 1892.8 lb. During 1958 the corresponding figure was 1613.4 lb. There are many individual furnaces where still better results are being obtained, and further reductions in the average may be expected. Perhaps the greatest threat to the merchant coking plant has been the fantastic increase in the use of natural gas and petroleum products for purposes which manufactured gas once served. So deadly has the com- petition from natural gas and oil been that it has almost eliminated by-product oven installations owned by public utilities. In the peak years of the early 1930's there were 23 such public utility plants. In 1960 only two were left. One of these, owned by the Citizens Gas and Coke Utility, was at Indianapolis, Ind.; the other was the plant operated by the Philadelphia Electric Co. at Chester, Pa. The non-utility merchant plants have also been sorely hit. With gas sales revenues reduced, domestic

Jan 1, 1961

By M. Deighton, R. N. Parkins

The metals Cd, ,Wg-, Sn, TI, Zn, and Zr reach a peak hardness after a criticfir1 deformation by rolling- and then soften with fwther rolling-, thereby exhibiting wovk softening. Optical metallography on Cd, Mg, and Zn shows that work softening is accompanied by a change in grain size occurring during deformation. The creep of zinc from -1l° to +60°C at stresses in the range of 7.9 to 17.3 kg per sq mm is given by € = e0 -t- Bt + Kt +at6. The third and second rate constcints are related by the equation a = K~ K6 and their stress and temperature dependence can be represented by the equations K = A, . exp - (u, - Bu)/kT. A model based upon the stress activated glide of sub-boundaries is proposed which qualitatively accounts for the metallog-raphic observations. Expressions, which are in reasonable quantitative agreement with the ex-pe~inzental observations, are derived for the creep of zinc. THE term "work softening" has been used previously by Polakowski1 and by Cottrell and stokes2 to describe phenomena where further strain of a deformed material leads to a decrease in flow stress. In both cases, however, the conditions were changed for the second straining. Here, the term "work softening" is intended to refer to a decrease in flow stress after continued straining in the same direction at the same temperature: work softening is the antithesis of "work hardening". Work softening of zinc was reported by chadwick3 and in discussion of that paper Jenkins4 indicated that cadmium also work softens. More recently work softening has been reported5 in two magnesium alloys, -99.5 pct Mg. Chadwick found that the hardness, 0.2 pct Proof Stress and the UTS of electrolytic zinc all increased with progressive cold reductions up to 30 pct and then progressively decreased with further rolling. Gay and Kelly6 used a back-reflection X-ray technique to study the effect of cold rolling zinc and found that although deformations greater than 2 to 5 pct reduction in thickness produced some recrystallized grains, deformations greater than 40 pct caused com-plete spontaneous recrystallization. At deformations greater than 60 pct the material was found to consist solely of recrystallized grains, -20 pm diam, the size of which decreased with increasing reduction and was much less than the initial grain size of the annealed material (-300 pm diam). Similar results were also reported for cadmium, tin, and lead.6 Gay, Hirsch, and Kelly' suggest that these experiments indicate recrys-tallization takes place when the dislocation density exceeds a certain value. However, no measurements of MATERIALS AND EXPERIMENTAL PROCEDURE The purity of the metals used in this work is indicated by the following figures: Zn (99.99); Cd (99.94); Mg (99.95); T1 (99.99). The zirconium was iodide crys tal bar with a probable purity of about 98 pct. The metals were obtained in the form of 0.25 in. thick strip or 0.425 in. diam rod by various fabrication methods and then annealed to ensure complete re-crystallization. Hardness-deformation curves were obtained at room temperature by rolling 4 in. thick strip under conditions which left a surface adequate for diamond pyramid hardness tests immediately after rolling. The hardness was taken as the niean of five impressions made using a 5 kg load and the time elapsing between rolling and making the last impression never exceeded 5 min. The zinc specimens for creep testing were from 3 by 3 by 4 in. cast slabs which were rolled to 0.10 in. thickness starting at 350°C and finishing cold. The resulting strip was cut into pieces 1 in. wide and annealed in batches. With suitable choices of annealing temperature between 100" arid 400°C five different grain sizes varying from 4.54 x 10' to 3.03 x l05 grains per sq cm (530 to 20 um diam) were obtained. Creep tests were done in compression using a sub-press, based on a design after Ford,8 in which the strip is compressed between dies 0.100 in. wide under conditions of plane strain. Since there is no lateral spread of the material, the area of contact between the dies and strip remains constant throughout the test and the application of a constant load, using the load maintaining device of a hydraulic testing machine, resulted in a constant stress. Covering the dies with strips of P.T.F.E. reduced frictional effects to a minimum. The creep strain was obtained by measuring the travel of the crosshead of the testing machine to a sensitivity of 0.1 pct reduction in thickness. The complete subpress assembly was contained in a steel box and for tests above the ambient this was filled with liquid paraffin and heated electrically. Temperatures below the ambient were obtained with a cooling mixture of acetone and solid carbon dioxide in the box. The liquids were stirred and the temperature of the specimen, which was controlled to ±0.5"C dur-ing a test, was measured by a thermocouple placed near the dies. Compression testing of cylindrical specimens was also carried out in the subpress using hardened flat discs separated from the test material by P.T.F.E. sheets which obviated barrelling of the specimens. Various initial strain rates were supplied by the hydraulic testing machine, and the deformation was measured by a clock dial gage resting on the cross-

Jan 1, 1970

By Arthur Baker

The orebodies are long bedding-plane lenses of chalcopyrite and sphalerite, associated with garnetite masses. Most of the orebodies are within a 50-ft thickness of Cambrian limestone; other Paleozoic limestones and dolomites are locally metamorphosed but only slightly mineralized. Pre-mineral faults are numerous, but shallow folds were the main ore-localizing structures.

Jan 12, 1953

By A. W. WALKER

All branches of production engineering showed steady and definite progress during 1941. Most of it has been of the slower and more conservative type rather than the sensational. To a large degree the changes have been influenced by the expanding war economy, and this tendency will probably be even more marked during the coming year. The stress of the times is placing more emphasis on the principles of engineering and conservation, with the object of obtaining the greatest possible recovery with a minimum waste or expenditure of equipment. Also available material supplies are often being turned to new uses.

Jan 1, 1942

By Warden A. Moller

(Pittsburg Meeting, March, 1910.) THE Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of Mukden, the capital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Mukden, consists of a long narrow valley,. running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 20 ft. of alluvial, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lauds and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent is good coal. The seam dips to the north conformably with the shales, at angles of from 25° to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut o$' by the northern hills. The coal-bearing shales extend east and west for a length of about 20 miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal-quick steam-raising and poor stacking-qualities. Pieces of resin, varying in size from

Apr 1, 1910

By AIME AIME

AMONG the industrial motion pic¬tures released in the last year of possible interest to people in the mining industry are the following: "A New World Through Chemistry," made by the public relations department of E. I. du Pont de Nemours & Co., Wilmington, Del. This film, which is in sound and color, interprets in twenty minutes of narration and ingenious photography many of chemistry's newest developments. It may be borrowed either in 16-mm. size on an 800-ft. reel, or 35-mm. size on a 2000¬ft. reel, the only charge being the cost of returning the film. Douglas D. Rothacker, 729 Seventh Ave., New York City, is prepared to loan free of charge except for transportation each way several films prepared in the plants of the International Nickel Co., 16 mm. with sound. These include: "Nickel High Lights," 35 minutes; "Nickel Mining," 18 minutes; "Nickel Smelting," 18 minutes; "Nickel Refining," 9 minutes; and "Copper Refining," 6 minutes.

Jan 1, 1941

By George W. Powel

IN the nation's effort to raise its magnesium metal supply to meet the ever increasing demand, the Government is relying not only on standard established practice but has extended its support to developments not so well proved-at least, not commercially proved. Within the past few months considerable progress has been made, not only in the definite output of metal but in the exploitation of new processes, the successful adaptation of which should, in a reasonably short time, assure an adequate supply of magnesium. Recent months have also witnessed a reshuffling of the favored methods as well as of the likely raw materials, with the mineral dolomite gaining in interest over its richer but less abundant competitor, magnesite, while the lowly sea water appears to be losing ground to the higher magnesian brines of Michigan and western Texas. Every month sees a new alignment and there are signs that still newer methods or raw materials will be in use before the industry finally stabilizes itself.

Jan 1, 1942

BENEFICIATION AND CONCEN'TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979

By W. W. Lowry, G. C. Eggleston, W. E. Keck

THE potential iron ores of Michigan can be classified from the stand- point of the predominant impurities into siliceous, sulphurous and phosphorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral-specular hematite and massive hematite. The latter is the principal variety, but the former is an important mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (1) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1937

By AIME AIME

The name and address of the school are given first, followed by the length of the regular undergraduate curriculum, the degree granted, types of courses giben, and the name of the man in charge. This covers only work for the first or Bachelor degree in each case. The following abbreviations are used: B. Bachelor Cer. Ceramic. E. Engineer or Engineering Eng. Engineering or Engineer Geol. Geologist, Geological, or Geology M. Mines or Mining Met. Metallurgy or Metallurgical Mng. Mining Pet. Petroleum Ref. Refining S. Science Tech. Technology or Technical

Jan 1, 1939

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

By Gerald Edmunds

Although the phenomenon of season cracking is still imperfectly understood, there seems to be ample evidence that season cracks are propagated by the combined action of corrosion and a stress of either internal (residual) origin or external origin. The factors that influence season cracking may therefore be grouped according to corrosive media, nature of stress, and character of the material. Thus the important mass of evidence pointing to ammonia as the most frequently active corroding agent causing season - - cracking of brass has naturally led to the development of laboratory tests of a moderately accelerated character based upon ammonia together with auxiliary agents such as air, water vapor, and carbon dioxide as the corroding agent. Similarly, the knowledge that stress must be present has led to the use of externally applied and therefore accurately measurable stresses in laboratory testing. A companion paper(^)^ to the present one discusses the development of these test methods in our laboratories. The present paper discusses data bearing on factors concerning the nature of stress such as its magnitude and direction of application. It also deals extensively with the character of the brass, particularly in regard to the copper-zinc ratio and the structure as developed by mechanical work-

Jan 1, 1945

By Basil Prescott

Resume.-The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre¬mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide types occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore. The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition.

Jan 2, 1915

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By Laurence Hicks

CONSIDERATION of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grübe and Fleischbein1 packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmos-phere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that 'in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a later paper Grübe extends his work to other systems which show the same characteristics.2 He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kelley3 points out that Grübe has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1933

By V. M. Lovell

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysaccharides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By J. S. Koehler, F. Seitz

THE dislocation theory of plastic flow originated in 1928, when Prandtl1 suggested that the internal damping of metals of plastic origin might arise from the motion of a crystalline imperfection. Following this, Dehlinger2 employed a similar imperfection in a theory of recrystallization. The first detailed theoretical discussions were those of E. Orowan3 and G. I. Taylor4 in 1934. The resulting theory was gen- eralized by J. M. Burgers5 in 1939. Mott and Nabarro, in England, and Seitz and Read,6 in the United States, started an extensive examination of the atomic theory of dislocations in the period between 1939 and 1941. However, this development was arrested by the mar and was not taken up again until after 1945. Since 1946, the field has been the object of very intense activity, particularly in the United States and England. Dislocations are beautiful and intricate imperfections; they are sufficiently complicated to account for the great variety of phenomena encountered in the field of plastic flow. Above all, the dislocation concept enables us to understand how a metal or other plastic solid can deform inelastically under very small stresses at temperatures far below the melting point. Suppose we attempt to shear a perfect crystal plastically. This can be done by sliding one entire atomic plane simultaneously through one atomic distance with' respect to the near-

Jan 1, 1954

By Edwin R. Phelps

In the year 1900 about 212 million tons of bituminous coal were produced in the United States. Almost none of this was produced by surface mines (Fig. 1), because there was no large equipment suitable for stripping overburden at that time. By 1915 the surface mines had built up their capability largely through use of the steam shovel to the point that they produced 2.8 million tons of the nation's total production of 443 million tons. Over the intervening years between 1915 and 1970 surface mining provided a continually increasing percentage of the nation's bituminous coal, stimulated by the growing availability of giant surface mining machines, some of which are presently capable of removing 220 cu yd of earth with one bite of their mighty buckets. In 1970 the nation's surface mines produced 244 million tons of bituminous coal, over 40% of the total national production. On the other hand, the nation's underground mines hit a peak of 560 million tons in 1920, dropped to a low of 273 million tons in 1961, and are presently on a very slow rise. Environmental pressures generally oppose surface mining, and have forced coal companies to consider more underground mining in future planning. Also, since strippable reserves are decreasing in the eastern states, an increase in underground mining is expected over the coming years. However, in the western states there are enormous reserves to be extracted by surface methods. Why has surface mining increased, while underground mining has decreased? It's largely a matter of economics. The cost per ton is greatly reduced by surface mining because of the relative ease of obtaining the coal. Also, there is a much greater percentage of coal recovery-nearly 85% in surface mines within the minable area, as compared to an average of about 50% in underground mines. Much surface mining recovers coal that could not be extracted by underground methods because of coal bed thinness, or multiple beds close together, split seams, the nature of the roof, and other geologic conditions. What are some of the limitations of surface mining? First of all, with presently available machinery it is difficult to surface mine at depths

Jan 1, 1973

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947