Search Documents

By Samuel L. Hoyt

THIS paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by von Gomperz,2 was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disk floats on ,the melt, and is provided with a central hole about 1 mm. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started.. The capillary brings up a small quantity of molten metal with it to a point just above the lava disk. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

By RAYMOND M. LARSEN

The area covered by this paper is the same as that covered in 1944. Colorado, Montana, Utah, and Wyoming are included in the discussion and statistics, and brief mention is made of activities in the adjoining states, except Nebraska and New Mexico, which are considered separately (see pp. 187-189). The other adjoining states, North and South Dakota, Arizona, Nevada, and Idaho, have had virtually no oil or gas production, except in the gas field of Cedar Creek. Montana, which extends into North Dakota; the Pierre field in South Dakota, where gas is produced and separated in gas-water wells, and the abandoned Payette area in western Idaho. Seven gas wells were drilled in North Dakota, but no wildcatting was reported. Several unsuccessful wildcats were drilled in South Dakota, and some were continuing at the end of the year. Activity in Idaho and Nevada was negligible.

Jan 1, 1946

By Marius R. Campbell

VARIOUS classes of coals are recognized in this country at the present time. These classes depend largely upon physical characteristics rather than upon chemical composition, and consequently they cannot be accurately defined. The divisions into anthracite, semi-anthracite and semi-bituminous are fairly satisfactory; but the term bituminous embraces so large a variety of coal that it is of little value, and the term lignite is so loosely applied that it has little or no place in a scientific classification. At present there is no way of accurately defining the vari¬ous classes of coal, because no adequate scheme of classification, which applies to lignites as well as bituminous coal and anthracite bas been proposed. The object of this paper is to present such a scheme, which is based upon data obtained dur¬ing the past year by Prof. N. W. Lord,1 in charge of the chemical laboratory of the United States Geological Survey coal-testing plant at the Louisiana Purchase Exposition, St. Louis. All the classifications of coals proposed prior to 1877 were based either on physical characteristics or on proximate analyses, including all of the impurities. These schemes were illogical and highly unsatisfactory, for the physical properties of a coal give little indication of its true composition; and impurities, such as ash and sulphur, are largely the results of acci-

Sep 1, 1905

By Sydney H. Ball

I. INTRODUCTION. DURING the past 50 years the attention of mining-men has been turned to Africa, and within the past decade prospecting-expeditions sent into Central Africa have resulted in the opening-up of several mines. Having recently spent two years in the Belgian Congo for the Société Internationale Forestiere et Miniere du Congo, it is our purpose to outline briefly the mining-conditions in that part of Central Africa. Before it became, in 1908, a Belgian colony, this region was known as the Congo Free State. II. LOCATION AND AREA. The Belgian Congo lies in southwestern Central Africa, west of the continental divide, is illustrated in Fig. 1. It has a coastline of but 20 miles on the Atlantic, but widens rapidly eastward to points 5° north and 14° south of the equator. Its area is 908,000 sq. miles, which is almost one-quarter that of the United States and Alaska, or more than one and one-half times that of Alaska. Stated in other terms, its area is nearly one-third that of the United States, exclusive of Alaska and the insular possessions, or more than that of all the United States east of the Mississippi river. III. TOPOGRAPHY AND DRAINAGE. From north to south, Africa is made up of three topographic elements: 1, the Atlas mountains, a highly-accentuated region

Apr 1, 1910

By B. L. Averbach

THE rolling process may be considered as a case of a nonhomogeneous plastic flow. In such a heterogeneous deformation there is no direct general solution, and the plastic deformation varies from point to point as a function of the coordinates. It is practicable to determine these plastic strains only at the conclusion of the rolling process, and the local strains can be studied by observing the deformations produced in a suitably placed grid system. Strains at the surface of a bar after rolling have been reported by MacGregor and Coffin,' but the strain distributions within the bar have not been previously observed. Siebel² has investigated the plastic deformations resulting from wire-drawing by splitting the wire along its axis, milling a grid coordinate system on the inner plane surfaces, and binding the .wire together so that it would pull through a die as a single unit. This method was possible because of the rotational symmetry of the die. In the rolling process, however, such a system was not readily applicable. This paper describes another method of including a grid system, and reports some preliminary data on the plastic rolling strains within a square bar. Experimental Procedure 2.1 mm wide (144 network squares per sq in.) was punched from a thin lead sheet with a steel die and supported in a brass mold by thin copper wires. Pure tin was then poured around the grid to form a solid bar, with the network securely imbedded at. a given position. This bar was then machined to a square 15.2 mm (0.60 in.) wide, and then radiographed. The lead grid was quite adherent and sufficiently ductile to follow the deformation of the bar faithfully. The network lines also remained sharp enough to maintain a high radiographic contrast, and the tin bar, with the grid included, could withstand considerable deformation at room temperature without splitting at the interface. In order to fill the mold, it was necessary to cast the tin at 260-280°C and during pouring the lead grid was supported at short intervals to prevent warping. Some shrinkage cavities were encountered, but only bars which were free of shrinkage in the network region were used. This method is similar to the one employed by Steinberg" in an investigation of the strain distribution in a tensile specimen. Before rolling, the machined bars were radiographed in two directions to obtain accurate initial dimensions of each square and to observe whether the grid was straight and correctly positioned. The rolling was performed in a small hand mill with 2 in. diam rolls at room temperature, and a 20 pct reduction based on the original height was employed. The rolls were clean and no lubricant was used. Halfway through the bar, at the center of the network, the rolls were reversed and the bar extracted. These bars were then radiographed again

Jan 1, 1951

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Arron Finger, Laurence Delisle

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By A. A. Steel

(Spokane Meeting, September, 1909.) DURING. the summer of 1905 I was employed by the U. S. Geological Survey to investigate the geology, Mining, and preparation of barite in most. of the fields of the United States. The Eastern districts have been more or less completely described ; the Virginia field in detail by Thomas L. Watson, in his paper, Geology of the Virginia Barite-Deposits,' and other fields in abstract., including statistics of production and references to current literature, by various authors .2 There have also been published a few details of the occurrence of barite in the lead-mines of Washington county, Mo.3 The other accounts of this district are erroneous and meager, and since this field is the most important one in the United States at the present time, a detailed description of the local geology seems doubly desirable. Barite-deposits are scattered over nearly the whole of Washington and adjoining counties, but. the product, is all mined from the areas indicated upon the sketch-map, Fig. 1, and is shipped from the stations of the St. Louis, Iron Mountain &. Southern railway, between Blackwell and Potosi, from 45 to 60 miles SW. of St.. Louis. The topography is for the most part gently rolling, with slightly graded streams, usually less than 200 ft. below the higher hill-tops. Along Mineral fork and Indian creek are :some steep bluffs and cliffs, affording good exposures of the

Feb 1, 1910

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By F. R. Hensel

The present paper describes a number of experiments with fine silver, coin silver, silver-cadmium oxide and silver-nickei-copper compacts, prepared by powder metallurgical methods. The test data are of a preliminary nature, since most of the work was exploratory. Fine Silver Eject of Compacting Pressure on Hardness and Density during Cold and Hot Pressing The cold-welding properties of silver have received considerable attention and the welding characteristics are functions of such variables as: cleanliness of metal particles (impurities and adsorbed gases), chemical nobility of particles, plasticity and hardness, particle assortment, particle shape, particle porosity, apparent density, temperature, pressure, time, recrystalliza-tion characteristics. Chemical nobility, plasticity and low temperature of recrystallization after work-hardening are responsible for the excellent low-temperature bonding properties of silver. Several series of compacts were pressed at pressures of 5, 10, 20, 30, 40, 50, 60 70 and 80 tons per square inch, at temperatures of 32°C. (room temperature), l00°, 2000, 300°, 400°, and 450°C. Silver powder of minus 325-mesh, produced by displacing silver from a nitrate solution by means of copper, was used. The density was calcuiated from accurately measured and weighed compacts. The hardness was measured on the Rockwell F scale. The investigation shows that an increase in pressure promotes a higher density and hardness regardless of pressing temperature, up to a temperature of 400° C. The pressure-density curves at various pressing temperatures are shown in Fig. I, the pressure-hardness curves at various pressing temperatures, in Fig. z. The greatest increase in both hardness and density was obtained in the pressure range of 5 to 20 tons per square inch. A compact from each series was annealed at 300°C. in air, for various lengths of time. The hardness values after annealing are shown in Table I. A minimum hardness was obtained after one hour of annealing. No change in density occurred during annealing. The maximum density was obtained at 80 tons per sq. in., and at this pressure the hardness is equal to that of hard-drawn wrought

Jan 1, 1945

By J. E. Harris

The metallic elements, beryllium, calcium, cerium, lithium, manganese, titanium, vanadium and zirconium are used in metallurgical practice in relatively small percentages for the purpose of improving the physical properties of various alloys. No important uses for any of these elements have thus far been developed either in the pure form or in alloys of which they constitute the major constituent.

Jan 1, 1935

By David, Levinger

THESE observations of the metal-working industries of Europe are based on a three months' tour of eight countries of Europe, in which 75 industrial establishments were visited in England, France, Germany, Belgium, Holland, Italy, Austria and Switzerland during the summer of 1927. Since the Western Electric Co. is a large consumer of copper and brass, these industries were of particular interest and differences in practices were of keen interest to us.

Jan 1, 1928

By K. A. Natarajan, S. C. Riemer, I. Iwasaki

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration (nitrogen, air, and oxygen) on ball wear was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. Marked ball grinding tests and electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen toward wear (corrosive wear) is relatively small, and abrasive wear appears to be significant. Rheological properties of the slurry appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1985

By Colin M. Sargent

THE electron diffraction pattern as seen in the electron microscope represents an approximately plane section of the reciprocal lattice. Identifying the zone axis of a diffraction pattern is often laborious for a crystal of low symmetry, especially if several crystal orientations are present. A program has been written in FORTRAN II (Version 2) for the IBM 1620 which will assist in plotting out reciprocal lattice sections. The calculation is performed by choosing a zone axis [uvw] and determining the d spacings and angle between the planes (Ow - v) and (wO - u). (This procedure is varied slightly for zone axes with Miller indices equal to zero.) Cartesian coordinates for the reciprocal lattice points are then calculated for these planes and for (ww— [u + v]). Any reciprocal lattice points within the parallelogram formed by the origin and these three points are then computed. The input and output are best described by use of an example (Monoclinic ZrO2) used in the author's work. Input consists of two cards: 1) The crystal parameters: a, b, c, a, 8, y, e.g., 5.1477, 5.2030, 5.3156, 90.000, 99.380, 90.000. 2) Three numbers, D, E, F, e.g., 5, 3, 3.0710-the first is the limit of the sum (u + v + w) considered; the second limits the absolute value of u, v, and w to (E- 1), e.g., 2, so that zones (221) would be the highest order considered in this example; the third, F, is the required constant, yL. Output is in the format shown in Table I. The reciprocal lattice sections may then be plotted on standard graph paper and compared with the unknown diffraction pattern. (Note that no attempt has been made to deal with systematically absent reflections.) A card deck for the program is available from Colin M. Sargent, ARZ, W-PAFB, Dayton, Ohio, 45433.

Jan 1, 1969

By AIME AIME

AT Williams College, in the quaint old New England town where people still go to the post office for their mail, an interesting institution has come into being as one of the aftermaths of the peace conference at Paris in 1919. The war taught the world many things about economics although much remains to be learned and more to be appreciated. B. M. Baruch, H. A. Garfield, president of Williams, and others who took part in the conference at Paris or in preparation for it, feeling that benefits would accrue from informal friendly discussion of the problems that lead to political differences between peoples, called together a summer conference in 1920. This has now become an annual affair and is coming to be looked upon as an important center for developing and stimulating public opinion. Membership in the Institute is by invitation and the lists change to correspond with the particular subjects taken up. Each year a number of distinguished foreign public men are invited to be the guests of the Institute and to meet men and women from various parts of the United States interested in their special subjects. Round tables, general conferences, and public lectures are the means employed to bring out discussion. The first are organized by groups, each including usually 25 to 40 people interested in a special subject and meeting three times a week for informal discussion. Teachers, writers, economists, engineers, business men, indeed men of all vocations and many shades of opinion, are brought together. Once a week each round table presents in general conference with the members of all other groups the more general conclusions reached in its own decisions. Afternoon and evening lectures are given by the foreign guests and these are open to the public. The lectures and the general conferences are reported widely in the press but the proceedings as a whole are not printed, no resolutions are passed, and no action is taken or contemplated. The whole plan is to furnish a forum for free discussion in hopes that the difficulties of various groups and peoples may be taken up sympathetically and good understanding promoted. There is no creed, doctrine or dogma to which the Institute is committed and widely different views are currently presented. The constant effort is to bring out points of view and the reasons for them rather than to build up convincing arguments favourable to a specific action

Jan 1, 1926

By J. D. A. Morrow

TO my mind the National Bituminous Coal Act so far has proved one of the unhappiest experiences that has ever befallen the bituminous coal operators of the United States. Viewed in the light of its ugly consequences everyone should recognize this measure for what it is -a weird thing as unreal as a page from "Alice in Wonderland." Indeed it might be another stanza to the tale of the Walrus and the Carpenter, with the coal operators in the role of the unfortunate oysters who were taken on that memorable ramble. It is time that coal producers open their eyes, jerk themselves out of any lingering hypnotic optimism about the price-fixing provisions of this law, demand the repeal of these corroding clauses, and then set about remedying as best they can the disastrous effects of this retromingent scheme to regulate the coal business.

Jan 1, 1939

By B. M. Larsen

Jan 1, 1948

By B. M. Larsen

Jan 1, 1948

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913