Search Documents

By C. E. Birchenall, C L. McCabe

IN attempting to extend vapor pressure measurements of the type previously reported by Schadel and Birchenall1 for silver and by Schadel, Derge, and Birchenall' for silver-silicon to other systems, it was observed that the materials melted at indicated temperatures 10" to 15" below their accepted melting points. Further investigation revealed that the thermocouple readings were in error due to appreciable conduction losses along the reference thermocouple wires. If the wire diameter of the reference couple inserted into the Knudsen cell was reduced, the correction for the indicating couple changed in a manner tending to explain the melting behavior. When extrapolated to zero wire diameter from measurements with several reference thermocouples of different wire thickness, the melting point of silver then agreed with the indicated temperature at which silver chips were observed to coalesce into a sphere. Approximately the same calibration was given by observing the melting of small wires of silver or gold in the Knudsen cell connected in series with an ammeter, where the leads into the cell were very fine in order to minimize heat conduction. Unfortunately neither of these methods seemed to yield a sufficiently precise temperature calibration to match the apparent precision of the other aspects of the vapor pressure measurement. It was decided. therefore, to redetermine the vapor pressure of silver in another setup under conditions permitting precise temperature measurement. The vapor pressure of pure silver could then be used as an internal calibration of temperature in the older unit in making runs on alloys. This has been done; the present report is a correction to ref. 1. Experimental Procedure The apparatus, shown in Fig. 1, was very similar to that employed by Harteck,3 except that the orifice sizes were smaller and the residual pressure in the vacuum system was probably much lower. A small, sharp-edged hole, nearly circular in shape, was ground into the rounded end of a quartz tube. The orifice area was then measured by tracing the image at known magnification on graph paper and counting the squares enclosed. The silver specimen was sealed into the tube to make a Knudsen cell. A tantalum jacket surrounding the cell served to increase the uniformity of temperature. This assembly was placed in the bottom of a long quartz tube with an inside diameter of about 1 in., which was connected to the vacuum system through a ground joint sealed with picein wax well removed from the furnace. A thermocouple tube inserted through the top of the vacuum line reached into the tantalum jacket so that the thermocouple junction was immediately adjacent to the Knudsen cell except for the protection tube wall. A resistance furnace could be raised to cover the end of the quartz tube containing the cell in such a way that the cell was in the uniform temperature zone 13 in. from the end of the furnace. An ionization gage was included in the vacuum system in the cold lines of wide diameter, immediately beyond the ground joint. The vacuum system consisted of a mercury one-stage diffusion pump, backed by a Welch duo-seal mechanical pump. The pumps were separated from the reactor chamber by a dry ice trap. The ionization gage always read less than 10-5 mm Hg after initial outgassing and before each run was started. Each newly filled Knudsen cell was evacuated at high temperature overnight before the first weighing was made. The cell was returned to the system, heated for a measured time at constant temperature, cooled, and reweighed. The heating and cooling times were quite short since the hot furnace was raised to receive the reactor at the beginning of the run and removed again at the end. The tube heated or cooled quickly. The total mass loss was attributed entirely to effusion of silver vapor from the quartz cell, since empty quartz cells maintained constant mass through similar heating cycles. The vaporized silver condensed on the cold walls of the quartz tube extending above the furnace. Earlier studies in the induction heated unit had shown that the same vapor pressure was found for silver, whether the silver was in contact with the tantalum metal cell or with porcelain or quartz liners. The Pt-Pt-10 pct Rh thermocouple was calibrated against a secondary standard of the same material and found to agree with the published tables. Always operating in air at temperatures below 100O°C,

Jan 1, 1954

By C. S. Smith, L. Guttman

It is shown, from a study of geometric probabilities, that the average number of intercepts per unit length of a random line drawn through a three-dimensional structure is exactly half the true ratio of surface to volume. Since the surfaces can be internal or external, the area of grain boundary or of the interface between any two constituents in a micro-structure can be measured. Other metric relations are tabulated that may be of use in studies of the microstructure of polycrystalline, cellular, or particulate matter generally. IN many fields of scientific investigation the structure of cellular aggregates or random arrays of discrete particles imbedded in some matrix is observed on a two-dimensional section and inferences are drawn therefrom as to the real structure in three dimensions. The biologist's microtome slice, the petrologist's thin section, and the metallurgist's plane polished and etched sections are common examples, although the problem is a general one. Scientists have commonly limited their thinking to the same dimensionality as their structures, and the few attempts that have been strictly three-dimensional in character have been laborious and noteworthy. From a metallurgical standpoint it is often of considerable importance to know, in addition to the volume fraction of two or more components in an alloy, the amount of two-dimensional interface between crystals. Such grain boundaries (which may separate either two identical crystals differing only in orientation or two crystals differing in structure, and possibly also in orientation) have a determining factor upon the mechanical behavior. It is at these boundaries that melting commences, that stress-induced corrosion occurs, and that various precipitates (harmful or otherwise) first appear. The boundary is doubtless of equal importance in nonmetallic crystalline aggregates such as rocks, ceramics, and concrete, and the biologist is deeply concerned with the area of cellular membranes. Many synthetic cellular foams involve similar structural problems. The very term structure usually implies the presence of interfaces and a complete understanding of structure involves nothing but an analysis of the geometrical, metrical, and topological relations between the various interfaces (zero, one and two-dimensional) that exist in a three-dimensional structure. Even systems lacking sharp physical interfaces often have interrelated gradients of composition or velocity (as cored crystals or turbulence cells) in which a neutral surface can be treated as a two-dimensional interface. In an earlier paper by one of the authors' the question of cell shape was considered in terms of simple topological principles without regard to physical dimensions. The determination of the actual size of grains in two dimensions is carried out in a routine fashion in innumerable metallurgical laboratories (see, for example, the ASTM standard methods of grain size determination2), though this is done merely to check the uniformity of a product and has no relation to the actual three-dimensional shape or size of the grains. Some authors have discussed the three-dimensional problem but only on the basis of assumptions as to idealized grain shapes.:'-' Quantitative measurements of microstruc-tures to obtain the volumetric relations of various phases have been carried out by petrographers for many years and are of increasing popularity among metallurgists." The present paper will show how, on the basis of no assumptions other than randomness of sectioning (usually realizable in experiment), it is possible to learn a great deal about the three-dimensional structure. The relations to be derived will generally be used on random arrays of cells or other particles, although they are equally applicable to ordered arrays and even to isolated objects of complex shape provided that suitable random sections can be made. Total Area of Interfaces in a Sample Consider a typical microstructure of a single-phase polyerystalline metal, such as that shown pres- in Fig. 1. The plane cross section shown contains a network of lines which subdivides the area into two-dimensional cells. The lines, of course, represent merely the intersection of the two-dimensional plane of sectioning with the two-dimensional interfaces between adjacent three-dimensional cells. The structure also contains points at which two or more lines intersect: in three dimensions the points are, of course, lines. In the more general case there may be in three dimensions isolated particles surrounded by a single interface without contact with others, and both two and one-dimensional features which do not necessarily connect with others. On the two-dimensional section these will appear as areas delineated by a closed line (as at a and b, Fig. 2), as isolated lines

Jan 1, 1954

By Peter J. Conroy, Lewis V. Wade

Old Ben Coal Co. successfully completed the fit longwall panel in Illinois. The panel was mined wing shield supports and was part of a cooperative agreement with the US Bureau of Mines. This paper describes the rock mechanics studies which were performed to monitor: the performance of the supports, the stress changes in the coal and floor, convergence in entries, and caving mechanism of the roof. From this study, maximum support loads were obtained as well as the stress distribution in the panel, floor and adjacent pillars.

Jan 1, 1981

By T. F. Witherbee

The Iron Mountain, situated three-quarters of a mile NE. of the limits of the City of Durango, rises abruptly from a level plain, and trends N. 83' E. Fig. 1 gives a view of the mountain, with the company's iron-works. There are indications that the vein or deposit of iron-ore extends also about two leagues across the Murca ranch, in the same general direction. The Iron Mountain proper is divided into two great lenses by a horse of cantera or eruptive rock, some hundreds of feet in width.

Jan 1, 1902

By H. J. Rose

SIXTY-FIVE million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 TABLE 1.-Production and Disposition of Oven Coke in 1924 BY-PRODUCT BEEHIVE TOTAL Coal charged into ovens, tons 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons 33,983,568 10,286;037 44,269,605 Average yield of coke, per cent 69.3 61.6 68.1 Disposition of coke: PER PER PER CENT. CENT. CENT. Blast furnace 82.5 82.8 82.6 Foundry 4.6 13.3 6.6 Domestic 8.3 1.4 6.7 Water gas manufacture and all other uses 4.6 2.5 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke.

Jan 7, 1926

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

The Library of the above-named. Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 5, 1918

By Ossi V. I. Hintikka, Andrew Balint

Sorting tests on limestone at the Lohjan Kalkkitehdas Oy Ojamo mine, Finland, are described. The tests, conducted to evaluate a Sortex 811MW optical separator, were successful, and upon completion, the sorting machine was put into production. Optical separation characteristics of the limestone, used for cement manufacturing, are described. Problems of winter operation are discussed. Operating costs are given.

Jan 1, 1972

By Frank Somogyi, Donald H. Gray

Techniques for in-situ dewatering of tailings and slimes include evaporation, decantation, drainage under self weight, drainage by surcharging, and electro-osmosis. A promising technique for increasing drainage efficiency is a vertical, wall-drain system, which can be constructed in an impoundment concurrently with deposition of slurried tailings. The vertical drains, which can be constructed from sand or from the coarse fraction of a tailings stream, greatly speed the rate of consolidation of the fine tailings or slimes. The performance of a wall drain system and the semitidy of consolidation efficiency to certain variables or system parameters are examined. These parameters include the slime deposition rate, ratio of drain to slime permeability, drain width, and drain spacing.

Jan 1, 1979

Important chemical and other technical engineering work necessary, for the prosecution of this war is being carried on by the Bureau of Mines Experiment Station, at Washington, D. C. The services of trained men of the following classifications are urgently needed Bacteriologists Instrument makers Biologists Laboratory Assistants Chemists, Inorganic Laborers Chemists, Organic Machinists Chemists, Physical Physiologists Chemists, Electro- Plumbers Chemical Engineers Steamfitters Draftsmen Stenographers. Electrical Engineers Skilled labor of various kinds If your training fits you for any of these occupations, send to the Bureau of Mines, American University Experiment Station, . Washington, D. C. for blank forms. When properly executed and returned by you, these forms will be placed on file, and when a vacancy occurs you will be considered for it and will be notified if your services are desired. If you are a registrant in the draft, and have not yet been- ordered to camp, it may be possible to have you immediately inducted into the service for work here. If you are not in the draft, but feel that you wish to serve your country in the present crisis, you can enlist, or serve as a civilian. Serve your country where you can serve it best. VAN H. MANNING, Director.

Jan 6, 1918

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By H. Larson, J. Chipman

The ferrous and ferric oxide concentrations of slags, expressed as j = Fe+++/(Fe+++ + Fe++), have been established through gas-slag equilibrium at 1550°C in a range of oxygen pressure of 10-I to 10-9 equilibriumatm. The value of j is increased by basic additions (BaO, CaO, MgO, MnO) and decreased by acidic oxides (SiO2 and TiO2). Oxygen pressure is shown graphically as a function of composition for slags which are analogous to those at the slag-gas interface of the open hearth furnace. THE progress which has been made in recent years in understanding the chemistry of metallurgical slags has been based largely on studies of slag-metal and slag-gas equilibria. There is a considerable body of knowledge which is applicable to reactions occurring at the slag-metal interface in open hearth steelmaking. There is little information concerning reactions of the slag with the furnace atmosphere and hence little basis for an understanding of the transfer of oxygen, sulphur, or hydrogen between gas and slag. The oxygen pressure of the open hearth atmosphere is normally of the order of 10-1 to 10-3 atm which differs by several orders of magnitude from that of about 10" atm at the slag-metal interface. The chemical properties of the slag, for example, the ratio of ferric to ferrous iron and the ability of the slag to hold sulphur in solution, are greatly affected by changes in oxygen pressure. This investigation was undertaken to enlarge our knowledge of the effect of oxygen Pressure on steel-making slags. Using air or controlled mixtures of CO a CO2 a range of oxygen Pressures from 10.' to 10.' was covered. Review of the Literature There are only a few references in the literature which pertain directly to this investigation. The most important is that of Darken and Gurry1,2 on the system iron-oxygen. This work included the determination of the phase diagram of the system and also a study of the field of homogeneous melts and their oxygen pressures. Their apparatus and procedure were very similar to that used in this study. Iron oxide was melted in a platinum crucible under an atmosphere of CO2:CO, CO2:H2, H2O, CO2, air or O2 depending upon the partial pressure of oxygen desired. After equilibrium was reached, the sample was quenched and analyzed for ferrous and ferric oxide. By appropriate calculations these authors were able to determine the oxygen and iron activities in the various slags, heats of formation of the oxides of iron, and heats of solution of iron and oxygen in the liquid slags. In a subsequent paper' the same authors made a less thorough investigation of the effects of additions of lime and manganese oxide on the composition of iron oxide melts. Only a few experiments were made and those in a narrower range of temperature and oxygen pressure. Darken' has investigated the fusion temperature of iron oxide in contact with silica under various atmospheres. He found that the temperature changes from 1120° to 1447°C as the gas composition changes from CO2/CO equal to 20.8 to pure oxygen. A comprehensive paper by White" predates the work of Darken and Gurry. The decomposition of ferric oxide into oxygen and lower oxides of iron was studied from 1000° to 1650°C and under oxygen pressures from 2 to 76 cm of mercury. The effect of

Jan 1, 1954

By John Wulff, David A. Stevenson

The solubility of iron and cobalt in liquid lead, the solubility of chromium in liquid tin, and nickel in liquid silver were determined up to 1300°C in an atmosphere of hydrogen. Liquid samples were taken at different temperatures and analyzed. The data obtained were plotted to show the relationship between log mole fraction of solute and the inverse of the absolute temperature. Resulting values for the differential heat of solution (AH) and the excesspartial molar entropy (S)are: for the iron-lead system = _24,200 cal per mole and AT = 5.0 e.u. for the a phase, and AH = 18,300 and S = -0.1 e.u. for the y phase; for the cobalt-lead system AH = 16,500 cal per mole and AS =0.7 e.u.; for the chromium-tin system AH = 15,600 cal per mole and AS = 8.5 e.u.; for the nickel-silver system AH =18,000 cal per mole and AS = 4.0 e.u. RECENT developments in coating, brazing, and heat transfer have focused attention on specific cases of solid-liquid interaction in metal systems, particularly those involving dilute liquid solutions. One fundamental quantity of interest in such systems is the equilibrium phase distribution between solid and liquid phases. In any effort to fully understand such interactions, one must be able to describe the equilibrium state precisely. Furthermore, in order to develop genera! relations for such systems, one must know the equilibrium state in a number of different cases. This investigation was devoted to a study of the equilibrium phase distribution in four binary systems: solid iron-liquid lead; solid cobalt-liquid lead; solid chromium-liquid tin; solid nickel-liquid silver. The iron-lead system was previously studied by Shepard and parkman' and later by Fleischer and Elliott2 with differing results. Both investigations were carried out by sampling the saturated liquid, and analyzing it chemically. The cobalt-lead system was previously reported by Pelzel,3 who noticed no discontinuity near the transformation. A limited investigation of the chromium-tin system was made by Wlodek and wulff4 using a weight loss method. This work was done in conjunction with the development of a process for coating molybdenum with chromium from tin solutions. To more fully under- stand the kinetics of the process, a more accurate determination of a solubility was desirable. No significant data were found in the literature on the nickel-silver system. Data on the latter system were, however, relevant to the investigation of the corrosion kinetics of copper-nickel alloys in liquid silver as carried out by Harrison and wagner,5 EXPERIMENTAL APPARATUS AND PROCEDURE Of the techniques available for the study of such systems the most effective appears to be that of liquid sampling,2,6,7 which is the method used in the present investigation. A schematic diagram of the sampling furnace is given in Fig. 1. Large pieces of solute metal, in excess of saturation solubility, were added to 200 g of the solvent metal, and the entire charge placed in an alundum crucible. Analytical reagent or materials of chemically pure grade were used in all investigations. The crucible was contained in a zircon muffle tube positioned vertically in the uniform hot zone of a Globar resistance furnace. The tube was provided with a number of ports which permitted sampling at temperature and in controlled atmospheres or vacuum; the ports were also useful for evacuation and introduction of gases as well as for thermocouple measurements. A chromel-alumel thermocouple Sheated in a porcelain tube was used for temperature measurements. A purified hydrogen atmosphere was employed in all experiments reported in this paper. The hydrogen was purified by passing it first over hot copper gauze to remove oxygen and then through a molecular sieve immersed in

Jan 1, 1962

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By Klaus Detert

Fifteen and 18 pct Ni maraging steel and several binavy and ternary alloys of the iron-rich corner of the Fe-Co-Ni system have been studied. After annealing in the austenite range, these alloys were deformed slightly by cold rolling and subsequently aged. Compavison of experimental measurements at various processing stages indicates that small degrees of deforn~ation (5 to 10 pct reduction in thickness) do not influence hardness and strength or the aging kinetics. Electrical resistivity and ductility are somewhat redu]ced and the coercive force is substantially lower when compared to identical samples which were not deformed. The results are explained in terms of retained austenite which transforms into martensite with the small amount of deformation. RECENTLY there has been increasing interest in maraging steel for applications in electric power generators requiring a high ratio of power to weight.' Fifteen pct Ni maraging steel has been investigated to evaluate its properties and performance for application as high-strength magnetic rotor steel,' and a thorough investigation of the precipitation and transformation processes in this alloy has been conducted in this laboratory.3 The influence of deformation, which preceded the aging treatment, was also studied. It was found that a small deformation in the order of 5 pct has a rather striking effect in reducing the coercive force. Other interesting effects on the properties caused by such deformation have led to the more detailed studies reported herein. EXPERIMENTAL METHOD The methods used to produce the samples from 15 pct Ni maraging steel have been described elsewhere.3 The general procedure of hot forging and cold rolling to sheet has been followed. The composition is included in Table I which also contains the composition of the 18 pct Ni maraging steel grade 250 studied. More data about the material and the processing of the 18 pct Ni maraging steel have been recently reported.4 The experimental alloys of binary and ternary Fe-Ni-Co alloys were made by levitation melting in an argon atmosphere and casting into rod-shaped ingots 7 mm thick weighing 20 g. From these ingots 25-mm-long rods were machined to study the phase transformation by a dilatometer. These rods were then cold-rolled to strips, 2.4 mm thick. Annealing for austenitizing was done in tube furnaces in an argon or helium atmosphere followed by cooling in the water-cooled portion of the tube. Aging was done in a salt bath containing a neutral blend of Alkali nitrates and nitrites. Vickers hardness was measured using a load of 50 kg for 15 sec. Tensile tests were carried out on a hard beam tensile tester at a strain rate of 5 X lo-' per sec using flat samples with a gage length of 37.5 mm and a cross section of 1.25 by 6.25 mm. Estimated sensitivity was 5 K x strain and 0.35 kg per sq mm stress. Magnetic saturation was determined on small cylindrical samples, 2.5 mm in length and diameter, by measuring the force exerted by the gradient of a magnetic field of 1000 oe per cm in a mean field of 11,500 oe. The measured values could be reproduced within *1 pct. Coercive force was measured by a precision-type magnetic field probe in a magnetic coil as described by Foerster.5 The magnetizing field was 1300 oe. The samples were 5 cm long, 1 cm wide, and 2.4 mm thick. he coercive force was measured to within +0.1 oe. Electrical resistivity was measured by using a potentiometer on flat strips with a gage length of 100 mm and a cross section of 2.5 by 0.5 mm. The accuracy of the measurement was 0.1 pct but the reproducibility of the measured specific resistivity among different samples was in the order of 1 pct. The method used to prepare the samples for electron transmission has been reported elsewhere.3 RESULTS Fig. 1 shows the influence of deformation after annealing on the resistivity, hardness, and coercivity. The samples were annealed for 30 min at 1000"C,

Jan 1, 1968

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A SATISFACTORY mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.1 Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.3 EXPERIMENTAL PROCEDURE Half inch rods of alpha brass (nominally 70 pct Cu, 30 pct Zn) * were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.' In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pct nitric acid solution. The back-reflection Laue technique as described by Greninger5 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buerger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1948

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

By David T. Peterson

Calcium metal was found to deoxidize thorizcm at 1000° to 1200° C. The reaction kinetics were determilled and related to the diffusion coefficients of oxygen in thorium. The solubility of oxygen in thorium, the minimum oxygen concentration, and the diffusion coefficient were determined from 1000° to 1200°C. This firocess results in the lowest oxygen concentrations zohich have been reported for thorium metal. FOR many years it has been known that calcium metal will reduce thorium oxide to thorium metal. This reaction has been the basis for several methods of preparing thorium metal. From the equations giv-by Kubaschewski and vans, ' AF" for the reaction Cao, + Tho,(,) - CaO(,, + Th(,) was calculated and found to be -3.4 kcal at 1000°C, -2.5 kcal at llOO°C, and -2.0 kcal at 1200°c. Thorium is very slightly soluble in liquid calcium, and the solubility of calcium in solid thorium is very low. Consequently these metals would be in essentially their reference states. If thorium containing oxygen were equilibrated with liquid calcium between 1000° and 1200°C, the oxygen content of the thorium would have to be below the solubility limit in thorium. Oxygen is one of the impurities most difficult to remove from thorium and is the most abundant impurity in metal prepared by almost all known methods. Fortunately, oxygen does not have a large influence on the properties of thorium because the solubility in solid thorium is very low. EvenT in thorium containing 100 ppm of 0, particles of thorium oxide can be observed in the microstructure. In view of the incompatibility of thorium oxide and liquid calcium and the low solubility of thorium oxide in thorium, the deoxidation of thorium by this method was investigated. For thorium containing an amount of oxygen well in excess of the solubility limit, the reaction should proceed in the following sequence. The oxygen content of the thorium matrix near the surface would be depleted by the diffusion of oxygen to the surface. At the surface, the oxygen would react with calcium to form calcium oxide. To maintain equilibrium within the thorium, thorium oxide would dissolve to keep the matrix saturated. Consequently, the thorium-oxide particles would disappear first at the surface and then the particle-free rim would grow in thickness. If the rate-controlling step were the diffusion of oxygen through this layer of thorium which was growing in thickness in direct proportion to the amount of oxygen removed, the well known parabolic time law should be observed. If the oxygen concentration at the surface of the thorium and at the inner surface of the deoxidized rim were known, the diffusion coefficient of oxygen in thorium could be calculated from the parabolic rate constant. EXPERIMENTAL PROCEDURE The thorium metal used in this study was prepared by calcium reduction of ThF, by the method described by Wilhelm.' The analysis of this metal is given in Table I. The carbon was determined by combustion, the oxygen by the HC1-insoluble residue method, nitrogen by the Kjeldahl method, and the other elements by emission spectroscopy. A section of this ingot was hot rolled at 600°C to 1/4 and 1/8-in. thick plates. Specimens approximately 7/8 in. square were cut from these plates, and all surfaces of the specimens were cleaned and smoothed by filing with a clean file. Individual specimens were placed in 1-in. diam by 2-in.-long tantalum capsules. Approximately 1 g of clean, high-purity calcium was placed in the capsules and an end closure arc-welded in place. The tantalum capsules were sealed in Inconel crucibles to protect the reactive metals from oxidation. The entire loading procedure was done in a glove box filled with pure argon. The loaded crucibles were placed in a muffle furnace, controlled within 2OC of the desired temperature, for a measured length of time. After the specimen had cooled to room temperature, it was sectioned perpendicular to the large faces and through the mid-point of two of the sides. The sectioned specimen was mounted and polished through Linde A abrasive. The rim which was free of thorium-oxide particles could be clearly observed microscopically as mechanically polished. Twenty measurements of the thickness of the rim were made at equally spaced points far enough from the end of the

Jan 1, 1962