Search Documents

By M. K. Yen, W. R. Hibbard

Previous studies of plastic deformation of metals have emphasized the important role of bending and constraints during strain under relatively pure stresses.1"5 Some new phenomena such as early conjugate slip6 and polygonization7 are intimately concerned with the relief of bending stresses, the former by slip and the latter by a process analogous to re-crystallization. However, few analyses of the bending deformation of single crystals were found in the literature, and those8,9 are sufficiently previous to the modern interpretations of slip to invite further investigation in this area. The transverse bending mode of testing, using the two-point loading method, was selected because the center portion of the specimen may be considered as under a theoretically pure bending stress with a uniform bending moment. Considerable attention was given to both the lattice distortion and flow characteristics of the crystals during deformation. Experimental Proeedare A specimen under the action of equal and opposite couples at both ends is said to undergo pure bending. The shear and moment diagrams of a specimen under the two-point loading method of transverse bending are shown in Fig 1. The moment over the middle-third of the span is equal to PL/6, and the vertical shear is zero. Fig 2 (A) illustrates the stress distribution in the elastic range on a plane across the middle of the specimen. It can be seen that the normal stress has a maximum value at the extreme surfaces on the tension and compression sides, and decreases proportionately to zero as it approaches the neutral plane. However, when the plastic range is reached, the stress distribution is no longer a straight line relation, but changes in a manner which can be best illustrated as shown in Fig 2(B). The following calculation and stress analysis are mainly in accordance with the works reported by Timoshenkol0 and Kochendörfer.9 From the simple beam formula, the maximum normal stress will occur at the surface of the specimen. For a round specimen with a radius r and for a rectangular specimen with a height 2h and width 2b, the maximum normal stress, Sp, will be given by the following formulas: For round specimen: 2PL Sp = 3pr3 [1] For rectangular specimen: Sn = 8bh2 [2] Since it is reasonable to consider that slip takes place under the same conditions as in uniaxial loading, the resolved shear stress S?, along the operative slip direction will be as follows: For round specimen: 2PL sin x cos ? Sp = 3pr3 sin x cos ? [3] For rectangular specimen: PL S8 = 8bh2 sin x cos ? [4] where X is the angle between the specimen axis and the slip direction and X, the angle between the specimen axis and the major axis of the glide ellipse. It was also reported by Kochenclorfer9 that the critical bending moment, that is, the bending moment exerted on the specimen to initiate slip, should be higher than the value given by the equations stated above. Based

Jan 1, 1950

By C. S. Matthews, W. R. Strickler, M. Prats

To gain an insight into the deviations from normal behavior caused by dip. a mathematical study has been made of single-fluid five-spot floods in dipping reservoirs for flooding techniques likely to be employed in such cases. Streamline patterns and sweep eficiencies are computed for a number of different cases, and the results, where possible, are presented in graphical form. An increase in sweep efficiency can be obtained by moving the central injection well updip, and the opti~num position is found for several cases. The applicnhility of the results is discussed. INTRODUCTION Because of the growing importance of water flooding in California and in other locations where large angles of dip are quite common, it is important to know at least some of the effects of dip on the performance characteristics of water floods in such instances. In the past, only reservoirs having relatively mild dips have been wateflooded. Consequently, little is known today as to the effect of dip on the performance characteristics of a flooding operation from the point of view of field experience; and because of the complexity of the problem, little, if anything, has been done on the problem from the point of view of theory. There are two distinct aspects of the role played by gravity in a flooding operation. The first is that of the preferential segregation of the reservoir fluids at the time when the flood is to commence. The second is the role that it may play in affecting the performance of the reservoir during the course of the flooding operation. In this paper the reservoir is assumed to be filled with only one fluid, so that there is no preferential segregation of reservoir fluids at the commencement of the flood. Moreover, the injected and in-place fluids are assumed to have the same characteristics, so that in effect we consider only a single-fluid problem. Single-fluid results have been used as a guide in the past for predicting and interpreting the behavior of regular five-spot floods in horizontal reservoirs. It is thought that single-fluid results might likewise be used for five-spot patterns in dipping reservoirs as a norm to which the effects of the multifluid problems might he referred.* In confining our attention to the single-fluid case, we therefore do not consider the preferential segregation of injected water in the oil bank, or of the oil bank in the unflooded zone. Instead we consider the deviation from the behavior of a horizontal five-spot which is caused by use of flooding techniques (i.e., the flow potential pattern at injection and production wells) likely to be employed during flooding operations in dipping reservoirs. In other words, we consider effects which are caused by the pattern of injection and production well pressures which we choose to apply. Performance characteristics are given for the five-spot spacing pattern as a function of two parameters; one is the ratio of gravity head to potential difference bctwccn the high updip injection well and the low downdip producer of the same five-spot, denoted by Rg; the second is the orientation of the five-spot pat-

Jan 1, 1956

By S. J. Burns, W. W. Webb

The dislocation arrangements formed during unsteady propagation of cleavage fractures on (010) planes in LiF have been investigated by high-resolution etch-pit techniques and by X-ray diffraction topogvaphy. In impurity-hardened crystals, cracks propagating in any direction on (010) planes at velocities of about 103 cm per sec are usually accompanied by light plastic deformation which is enhanced wherever the crack is allowed to hesitate. Dislocations with [011] type Burger's vectors are often formed looped around the crack tip. They are dragged along with the crack tips leaving edge dislocations lying nearly parallel with the clearage surface about 5µ from it. These dislocations are easily overlooked since they may initially intersect with the cleavage surface infrequently and later may disappear from the crystals due to image forces during aging at room temperature. Although the plastic work associated with these dislocations is only comparable with the reversible (010) surface energy, an instability in crack propagation appears due to a limit of the velocity with which dislocations can be dragged along with the crack. Transition to a fully brittle nonplastic fracture mode occurs when the crack velocity exceeds the velocity with which dislocations can be moved by the stress field of the crack. TRANSITIONS between brittle and ductile modes of fracture appear to be common processes in the behavior of materials in which the flow stress is close to the stress at which brittle cracks can propagate. High-strength engineering alloys fit into this category and the transition from ductile to brittle modes of crack propagation may be associated with catastrophic failures in these important materials. The methods of theoretical mechanics indicate the geometrical conditions in which these processes may occur but the detailed mechanisms controlling the generation of dislocations in the initiation of the plastic mode and the process by which the loss of plasticity occurs on transition to the brittle mode are not yet clear. Since these mechanisms are not amenable to direct observation in engineering alloys we have chosen a semi-ductile alkali halide LiF as a model system in which to observe transition mechanisms between plastic and brittle modes of crack propagation. Cleavage cracks in this system are known to undergo a plastic-elastic transition at velocities between 103 to 104 cm per secl and dislocation configurations in LiF are amenable to study by optical-microscopic observation of dislocation etch pits2 and by X-ray diffraction topography.3 We have been able to identify a dislocation mechanism responsible for the transition from brittle to slightly plastic modes of crack propagation in LiF. A model based on this mechanism permits calculation of the critical crack-propagation velocity for this transition and indicates the importance of the stress dependence of dislocation velocity in determining the critical crack velocity. Of course, this model cannot be carried directly over to more complex materials but it is quite possible that its qualitative features are generally applicable. Dislocations intersecting fresh cleavage surfaces in LiF were reported by Gilman,4 by Forty,5 and by Wash-burn et a1.6 Such dislocations were construed to have been nucleated where the cleavage crack hesitated or stopped, near stress concentrators, such as cleavage steps, on the crystal face. The loci of such dislocations deposited On the cleavage plane in bands were called "stop lines" or "deformation zones". Gilman, Knudsen, and walshl measured the velocity of cleavage cracks in lithium fluoride by evaporating thin resistive strips on the crystal side and recording

Jan 1, 1967

By E. H. Jr. Dix

THE work of Merica1 and other investigators indicates that the phenomenon of age-hardening in. alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum. Company of America to determine the functions

Jan 1, 1932

By Paul W. Jeran, Vladimir Adamek

Characteristics of surface deformations i.e., sub¬sidence, inclination, curvature and horizontal strains, are evaluated, based on information obtained by direct field measurements over three longwall panels in the Northern Appalachian Coalfield. Surface deformations have been precomputed using Bals' and Knothe's theories. The results have been compared with Bureau of Mines field data to evaluate the applicability of the two theories to the U.S. min¬ing conditions. Measured horizontal movements and the resulting horizontal strains differ as much as 300 percent from precomputed values. Topography has no detectable effect on vertical movements but appears to have substantial effect on the development of horizontal strains. The horizontal deformations computed from our field measurements generally exceed the limits used in other countries to protect surface structures.

Jan 1, 1982

By C. R. Sundeen, C. W. Nicolson, J. D. McAuliffe, C. A. Campbell, P. D. Pearson

SHAFT SINKING SYMPOSIUM is a weighty term that could mean any number of things. However, in, this case it has been possible to utilize the transcription of the Annual Meeting Session of the same title and present it in much the same manner as the experts on the panel presented it to their audience Wednesday afternoon, February 18, 1953, at the Los Angeles Statler Hotel.

Jan 8, 1953

By Nick A. Hasenack, Heinz Kister, Rolf B. Vogel, Kees H. van Toor

A full survey of the laboratory and blast furnace tests carried out on two types of acid pellets is given. From the lab tests it appears that type B has a better low temperature disintegration index and a lower reducibility index than type A. The chemical composition and swelling indexes do not differ for both types. From the blast furnace test periods, carried out with a charge of 45% of pellets and 45% of sinter, it follows that both types of pellets lead to the same pig-iron production, blast furnace permeability, and blast furnace dust production. It also can be concluded that type B pellets cause a significantly higher coke consumption.

Jan 1, 1977

By J. E. Burke, C. S. Barrett

The fine lines shown in Fig I are typical of markings that ma): be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied: to them, such as deformation line4 or strain markinas, indicate this uncertainky. In this paper which repotts the results of a furthcr investigatinn of their nature, they will be called strain mxrkings. Introduction Mathewson and Phillips1 described strain markinps in 1 916 and concluded that they appear only after 20 pet deformation. They objected to the markings being called slip tines believing this term should be sewrved for surface markings protluced by plastic deformntion. In 1921. vogel² described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallo-graphic in nature, and since they resemble Seumann hands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matherwson reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as cvirlence that the markings coalesce into anncaling twins. and hence that they themselves are mechanical twins. Many attempts have been made to demonstrate directly that the markings are mechanical twins. In 1934, Samans described the results of X ray studies of two defomed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings arc mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5.8.7 although in no Ease was the original method of Samans employed. An

Jan 1, 1949

By C. S. Barrett, J. E. Burke

The fine lines shown in Fig I are typical of markings that ma): be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied: to them, such as deformation line4 or strain markinas, indicate this uncertainky. In this paper which repotts the results of a furthcr investigatinn of their nature, they will be called strain mxrkings. Introduction Mathewson and Phillips1 described strain markinps in 1 916 and concluded that they appear only after 20 pet deformation. They objected to the markings being called slip tines believing this term should be sewrved for surface markings protluced by plastic deformntion. In 1921. vogel² described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallo-graphic in nature, and since they resemble Seumann hands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matherwson reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as cvirlence that the markings coalesce into anncaling twins. and hence that they themselves are mechanical twins. Many attempts have been made to demonstrate directly that the markings are mechanical twins. In 1934, Samans described the results of X ray studies of two defomed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings arc mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5.8.7 although in no Ease was the original method of Samans employed. An

Jan 1, 1949

By H. Shaw

GRAVITATIONAL measurements made by means of the Eötvös torsion balance over any area enable a representation to be obtained of the total gravitational effects over the surface of that area arising from the combination of all sources of gravitational disturbance. The investigation of gravitational anomalies occurring in the upper layers of the earth's crust, in this way, has been attended with considerable success, and, especially in areas in which no undesirable disturbing factors were present, it has been possible to locate geological structures and mineral deposits with remarkable accuracy and also to delineate their confines and to indicate their depth below the surface with a certain amount of precision. Before this can be done successfully, however, it is necessary to determine the gravitational effect arising from all other extraneous .anomalies in order that these may be satisfactorily eliminated. Disturbing features giving rise to these gravitational anomalies may be divided into two classes, according to whether they are situated at or below the surface. The former are determined readily by a detailed leveling of the ground surface, and may be satisfactorily eliminated provided the specific gravity of the terrain material is known, but the latter are generally unknown, and can only be ascertained with difficulty. When, therefore, the observations obtained by means of the Eötvös torsion balance have been corrected for all surface irregularities, known as terrain and topographical effects, there remain residual gravitational values which are due entirely to subterranean conditions. The task of interpreting these results consists in disentangling the various subsurface anomalies, and subsequently in computing and recombining the effects of these various masses in order to verify the interpretation. When the gravitational anomalies are due to large and comparatively simple structures it is a matter of little difficulty to arrive at a satisfactory interpretation of the subterranean conditions, but in more complex areas, where the geological conditions are more complicated and several irregular features exist, the process of disentangling the various constituents of the complex mass arrangement is more difficult and requires the expenditure of considerable time and labor.

Jan 1, 1929

By H. J. Mutz

THE International Nickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody.

Jan 1, 1953

In introducing last year's Industrial Minerals Review, Stan Lefond accurately predicted that the 1974- 75 period would be quite difficult and frustrating. Although 1974 demand and prices for most industrial minerals were exceptionally strong, operating costs also rose rapidly-while shortages of supplies and equipment, symptomatic of an overheated economy, occurred from coast to coast. Thus, at the end of 1974 recessionary forces were accelerating-and the minerals industry will soon be facing falling demand as a consequence of sharp declines in auto production, housing, appliances, and other consumer goods. Moreover, when sales weaken, the high-volume, low-prices industrial minerals will incur sharply increased unit costs. To maintain adequate profit margins under these conditions will require cautious and perceptive management.

Jan 2, 1975

Chairman James F. Kemp :—I call upon Prof. Albert Sau-veur to open the general discussion on the subject of sound steel ingots. Albert Sauveur, Cambridge, Mass.:—I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain Rome very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my views. I have always remembered my astonishment, not to say dismay, some twenty years ago, when I beheld for the first time a steel ingot, a rail steel ingot, that had been split open from top to bottom. There was the pipe! There was an enormous cavity extending from a short distance from the top to nearly one-third of the length of the ingot; and when I was told that manufacturers seldom discarded more than one-tenth of the total length of the ingot it became evident to me that a large proportion of piped, and therefore, defective, or at least weak and dangerous, rails were manufactured; in fact, probably one rail out of six, nearly 17 per cent., of dangerous rails.

Jan 1, 1914

By Alden Greninger

THAT metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc alloys.1 In all three of these alloy systems the martensite structures result from transformation of the metastable ß phase when the speed of cooling from the ß range is sufficiently high to suppress decomposition into equilibrium phases. ? In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require readjustments of concentration. For example, the marten-site transformation in 60:40 (ß) copper-zinc does not begin until the temperature has dropped to about minus 30° C., and then continues down to minus 130° C. and probably even at lower temperatures.1 Further-more, martensite processes apparently proceed only while the tempera-ture is falling, within the proper range, and cease completely while the temperature is held constant; ? and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of martensite processes by postulating that the mechanism " . . . consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By A. E. Bellis, T. W. Hardy

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operatioqs. Hundreds of dollars are spent in the design and manufacture of milling cutters of special form for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring-the tool out "clean," is a difficult one and calls for no small amount of skill. In order to be on the safe side the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed stee1, in which metallographic means were used to determine the correct hardening tempcratures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accom- . panying table. Six specimens from the same bar of each kind of steel

Jan 1, 1917

By F. E. Jaumot, A. Sawatzky

IT as long been recognized that there is a need for accurate systematic data on diffusion in solids. Originally, such data were needed to check existing theories but, more recently, it would appear that it could be used most advantageously as a guide to, or a check for, much needed extensions of the theory of diffusion. The awareness of the conditions which are important to experimental accuracy, the availability of the materials for accurate experiments, and the techniques have improved to the extent that it would now seem to an experimentalist that, unless extensions of the theory are made which take into account the fundamental parameters of the atoms, the electrons, and the lattice in some detail, the field of diffusion will rapidly become an empirical or semi-empirical field. The present series of experiments was designed to provide accurate data on the diffusion of the elements of the IB and IIB subgroups in silver; that is, to provide data on the diffusion in silver of three face-centered-cubic elements with roughly similar chemical properties, but with different atomic or ionic sizes and, similarly, for three noncubic elements. The elements of these two subgroups have different valences, so that the data will not give any significant information on differences due to the crystal structure of the solute. The present paper reports data on the diffusion of copper and mercury in single crystals of silver; the data for the other elements of the IB and IIB subgroups were reported previously by the authors1'2 and by Tomizuka and Slifkin.8 Experiment The general technique used was identical to that previously described1,2 and will not be repeated here. In all cases, the sectioning technique and high specific activity isotopes" were used. The short half-life of Cu64 made decay corrections more important than for the other isotopes, and necessitated around the clock shifts while data were being taken. Each section was counted at least twice (as was true for all longer half-life isotopes) and a monitor was counted along with each sample. Data for the diffusion of mercury in silver are presented at a greater number of temperatures than for the other solutes. This is a result of two circumstances. First, six (of 30) samples had to be discarded because of pitting or recrystallization which occurred during the diffusion runs, even though the samples had sustained high temperature prediffusion anneals. Either of these was a very rare phenomenon in the other experiments, and their occurrence in this case is considered in more detail below. Second, the curves of the logarithm of the activity of the sections vs the square of the penetration deptht were, in general, quite good, but frequently seemed to show one point to have high activity and the next point to have slightly low activity in terms of the best straight line. When this occurred, there was remarkable regularity of the high-low sequence. In any event, the results, as far as diffusion coefficients are concerned, were not affected by this amalgam effect. In fact, the mercury data had the highest internal consistency of any of the data. Results Diffusion of Copper in Silver—-Diffusion runs were made at eight temperatures In the temperature range from 700° to 950°C, for times ranging from 5 to 45 hr. A linear curve of the logarithm or the activity vs the square of the penetration depth was obtained for all samples. Table I summarizes the results for individual samples and Fig. 1 gives a plot 02 the logarithm of the diffusion coefficients as

Jan 1, 1958

By D. A. Dahlstrom

WITHIN the past decade, certain economic, legal, and technological changes have intensified the necessity for an efficient classifier or deslimer of particles at and below the 200-mesh point. First, mechanization of mining has increased the percentage of clays, silts, refuse, and high-ash material in the run-of-mine coal. Second, many washing plants must rely on smaller percentages of fresh make-up water because of shortages, economic factors, or legal restrictions on waste water disposal. Finally, the crushing of middlings and coarse refuse plus the trends toward the finer sizes in sales has further increased the amount of fines produced per ton of mine-run coal. A joint consequence of these circumstances has been the augmented percentage and build-up of —200-mesh material in the finer coal fractions and tipple circulating water. This results in the following disadvantages to the operator: (1) Higher ash percentages in the fine coal caused in large measure by the greater ash content of the —200-mesh material, (2) more difficult or expensive recovery of the fine coal from plant slurries, (3) lower filtration, drainage, and drying rates caused chiefly by lower permeability and the greater surface exposed per unit mass of the finer particles, (4) greater difficulty of beneficiatiing the fine coal because of lowered equipment efficiency and the partial "coating-out" of the —200-mesh fraction on the coarser coal particles. Obviously some cheap but effective fine-size classifier must be developed to aid in solving the above problems. To eliminate the generally unwanted —200-mesh fraction from coal slurries, several methods are in use. Probably the most popular with coal operators is the settling cone wherein the larger particles settle downward to the apex of an inverted cone while the slimes and fines are carried upward by vertical fluid currents caused by the overflow of the bulk of the water at the outer rim. The main advantage of the unit is the low initial and operating cost since no moving parts are involved. Disadvantages are primarily low capacity per square foot or floor space and the loss of good coal in the overflow above the 100-mesh size due to localized, high-velocity gradients and nonuniform, fluid-flow patterns, especially at high loadings. Also, when high slime concentrations are present, desliming efficiency is severely injured.', ' Other methods employed are the drag and spiral classifiers and the hydroseparator.' These involve mechanical separations achieved by moving parts and naturally result in higher initial costs. As they are all based on the settling velocity of the particles at the mesh of separation under operating conditions, area requirements are again large per gallon of throughput if they are to classify at the 200-mesh point. Usually the selection is made to operate at a higher throughput and thus sacrifice some coarser coal in the slime overflow. Cyclone Possibilities in Desliming To overcome the disadvantages of present deslirning methods, it is necessary to use a device that exhibits a very stable and uniform flow pattern while greatly increasing the settling velocity of

Jan 1, 1952

By E. Furubayashi, T. Taoka, S. Takeuchi

Recrystallization textures developed from artificial nucleation around indentations were compared with spontaneously recrystallized textures in two rolled 3 pet Si-Fe single crystals with (111)[112] and (100) [011] orientations. Orientation of individual grains in some stages of their growth was also directly determined by a microetch-pit method. In both the crystals, the recrystallization texture was characteristic of each orientation regardless of any nucleation conditions, artificial or spontaneous, though artificially nucleated grains were more randomly oriented in finer stage. These results support the concept that the process of selection of growing grains controls the formation of the prejerred recrystallization texture. Discussion is given on the factors controlling the mobility of grain boundaries. Recrystallization textures are formed through a number of stages which are customarily called by the terms recovery, nucleation, and grain growth. Many experiments have been done to clarify the mech- anism of formation of recrystallization texture but no fully successful explanation has been proposed. The texture consists of oriented grains which nucleate at many sites of the deformed matrix and grow at the expense of the matrix during annealing. The current theories on the formation of recrystallization texture are based on the following two extreme hypotheses: 1) the oriented nucleation theory by Burgers et al.;1, 2 2) the oriented growth theory by Beck et al.3-5

Jan 1, 1968

By Alexander L. Field

The rate of elimination of carbon largely controls the time required to make a heat of steel by the basic open-hearth process and to an important degree determines the cost of refining. Practical experience has led to the generally accepted belief that the use of slags relatively high in iron oxide, such as are required to bring about rapid refining, leads to a certain sacrifice of quality in the product. As a consequence, a compromise must be made between the exceedingly slow rate of carbon drop which would correspond to the ideal case and the rapid rate which would best satisfy the condition of minimum cost. An increase in rate of refining necessarily implies an increase in the concentration of iron oxide dissolved in the metal. However, even for the infinitely slow rate that corresponds to slag-metal equilibrium, the metal would contain a certain definite concentration of dissolved iron oxide. It is a matter of great practical importance, therefore, to determine the quantitative relation between the minimum or equilibrium concentration of iron oxide in the metal and the higher concentrations which must actually obtain in practice. The present paper is devoted to the development of certain equations, derived from the established laws of physical chemistry, which will enable this relation between rate of refining and the degree of oxidation of the metal bath to be computed from operating data. So attempt is made to exhaust the possibilities of this general method of treatment. In considering rate of refining, attention is mainly confined to rate of carbon elimination. However, the equations are of a more general nature and their application may readily be extended. The results of the preliminary calculations given herein indicate that increased rate of refining may have a decided effect in increasing the concentration of iron oxide dissolved in the metal. The uncertainty which attaches to the calculated value for this relationship arises in part from probable errors in experimental data on which the calculations are based, and in part from the lack of complete or favorably disposed information on basic open-hearth practice. When the relation between rate of refining and degree of oxidation of the metal has been more accurately established than has been done in the present paper, it will then become possible to consider what comprises

By G. Krauss, J. M. Thompson, H. Y. Kumagai

Boron-doped p-type and arsenic-doped n-type source materials were used to deposit thin silicon films on amorphous fused quartz substrates by cathodic sputtering in argon atmospheres. All as-sputtered films were found to have high electrical resistivities of about 104 ohm-cm, despite controlled variation of the substrate temperature from 50O to 400°C. The high resistivity of the n-type films persisted even after postdeposition heat treatments as high as 1000°C, while p-type films showed a sharp decrease in re-sistivity to values on the order of 1 ohm-cm or lower after heat treatments above 650°C. X-ray and electron diffraction, together with transmission electron microscopy of the p-type films, revealed that the improved electrical properties resulted from two distinct processes. A primary crystallization or recovery within the pains, which were approximately 200Å diam in the as-sputtered films, accompanied the initial sharp drop in resistivity at 650°C. Following this process, a secondary recrystallization or discontinuous grain growth was nucleated in films heated at 1000°C. The resulting significantly increased size of certain grains and the corresponding decrease in grain boundary area accompanied an additional decrease in resistivity after heat treatment at 1000°C. The properties of thin silicon films are of interest because of their possible application in device technology. Although evaporated silicon films on amorphous substrates1-3 and both sputtered and evaporated germanium films4-' have been studied in some detail, sputtered silicon films have not been widely investigated. It has been observed that evaporated silicon films deposited at substrate temperatures below approximately 600°C are amorphous.1,3,9,10 At substrate temperatures higher than this, the films are polycrys-talline, sometimes exhibiting a fiber texture with the fiber axis normal to the substrate surface.' Similar results have been obtained with germanium films, although in this case the substrate temperature for the amorphous to crystalline transformation is reported to be as low as 150OC.5 The mechanism of film deposition by cathodic sputtering differs markedly from that of thermal evaporation. It might be expected, therefore, that the properties of sputtered and evaporated silicon films would also differ. The purpose of our study was to determine the effects of deposition conditions and heat treatments on the electrical resistivity, structure, and composition of thin silicon films sputtered on fused quartz substrates. EXPERIMENTAL DETAILS Apparatus. A schematic diagram of the sputtering apparatus is shown in Fig. 1. The vacuum chamber was enclosed by an 18-in.-diam by 12-in.-high Pyrex bell jar mounted on a stainless-steel base plate. Access holes in the base plate were used to supply argon gas to the chamber, to allow for various electrical feedthroughs, and to provide mechanical motion to the shutter between the source material and substrate. The chamber was evacuated by a pumping system consisting of a 720 liter per sec oil diffusion pump backed by a 13 cu ft per min mechanical pump. Ultimate pressures of less than 1 x 10-6 torr could be achieved. The substrates were securely mounted on the stainless-steel substrate holder by quartz tabs held in place by stainless-steel screws. Temperatures of the substrate holder were measured by a thermocouple inserted within the holder. A quartz lamp was used to heat the holder and temperatures as high as 420°C could be maintained. Deposition Conditions and Procedure. The substrates used were polished fused quartz slides 116 by 1-12 by 3 in. and were outgassed at 200°C for 1 hr at a pressure less than 1 x 10-5 torr before film deposition. This was followed by a presputtering period of 2 hr during which the movable stainless-steel shutter was so positioned that deposition on the substrate was prevented. At a sputtering voltage of 5000 v dc and an argon pressure of 0.03 torr, the cathode cur-

Jan 1, 1967