Search Documents

By Ma Guang, Huang Jinshou

In this paper we briefly describe measuring techniques and their practical use in the mining industry of China. A strain coefficient matrix of triaxial strain cell for a flat ended borehole is also introduced.

Jan 1, 1983

By Robin O. Williams

AN investigation has been made of the Ni-Cr system for the purpose of elucidating certain points, namely the nature of aging in both terminal solid solutions and the nature of the phase diagram. Information pertaining to solubilities and precipitation has been obtained. Experimentation Five alloys, Table I, were arc melted in a cold copper crucible using electrolytic chromium and car-bony1 nickel, both dry hydrogen treated. These 100 g buttons were homogenized 24 hr at 1300°C in dry hydrogen and air cooled. Powders were prepared by filing or pulverizing and subsequent heat treatment was done in vacuum or helium using titanium chips as a getter. Powder of —80 mesh was filed from the 60 pct Ni alloy quenched from 1000°C and was sealed in silica under vacuum using a 250 °C outgassing. After aging as indicated in Table I1 the lattice parameters were measured on the quenched samples using the standard cos" 6 extrapolation. These parameters are considered accurate to roughly 0.0001A. In all cases chromium lines of 2.8812 ± 0.0005Å at 30°C were found. Drastic quenching from sufficiently high temperatures produced very sharp body-centered-cubic lines in the first four alloys without indications of transformations. Temperatures to 1250°C were used. Solid samples less than 1/16 in. thick were quenched in water without transformation and the powders could be adequately quenched in small helium filled thin wall silica tubing using a water quench. For those powder samples which were quenched from the two phase field the relative intensity of the body-centered-cubic lines and the face-centered-cubic lines were estimated and extrapolated to give the indicated solubility data in Fig. 1. The data for the two higher alloys were somewhat limited, the plotted points being the lowest temperature where no nickel phase was found. Neither filing, abrading, pulverizing, nor cooling to —190°C produced any new diffraction lines for solid samples quenched from the single phase region, nor did the character of the body-centered-cubic lines change Single phase body-centered-cubic powders likewise did not change on cooling to —190°C. Also, samples which had some precipitation due to inadequate quenching showed no additional changes under these conditions. The first change apparent by X-ray diffraction form samples quenched almost fast enough to prevent precipitation was the diffuseness of the body-centered-cubic lines, particularly on the low angle side, For slower cooling rates the diffuse face-centered-cubic lines appeared. Work on the large grained castings showed profuse streaking through some of the Laue spots while oscillating patterns showed broad body-centered-cubic and face-cen-tered-cubic lines as well as some new lines. For the 23.6 pct Ni alloy the new lines corresponded to 2.16, 1.96, and 1.86A and were more similar in character to the face-centered-cubic lines than the body-centered-cubic lines. Samples which were air cooled gave only face-centered-cubic and body-centered-cubic lines which were still broad. One pattern indicated that face-centered-cubic (111) plane was parallel to a body-centered-cubic (110) plane. For those samples which were examined by light microscopy there were details which were not resolved. However, varied and beautiful structures were obtained. Fig. 2 is of an alloy quenched in a helium filled silica tube from the single phase region and shows particles associated apparently with dislocations which are arranged in low angle boundaries. Finer, general precipitation has also taken place within the grains. Figs. 3 to 5 show the variety of structures produced in these alloys on continuous cooling. It appears that there are four distinct modes of precipitation as evidenced by these, figures. Annealing these structures at higher tem-peratures in the two phase field gives structures as shown in Fig. 6, which shows nickel plates in the chromium matrix which reprecipitated nickel on a much finer scale of the final quench. Lower annealing temperatures and shorter times naturally give finer plates of the nickel-rich phase. Samples of the first four alloys were annealed for appreciable times between 900º and 1250°C and gave structures like Fig. 6. The relative amounts of the two phases were measured and extrapolated to give solubility data as indicated in Fig. 1. The point at 1250°C was deduced from data of Oxx.1 These and most of the other samples were checked for ferromagnetism but none was apparent. In fact, it appeared that the magnetic susceptibilities were not more than three times that for paramagnetic chromium. Discussion In Fig. 1 it is seen that the solubility of nickel in chromium can be represented by a slightly curved line on the usual log X vs 1/T plot, These data are believed to be accurate to roughly 5 to 10º. There is only fair agreement with the data of Taylor and

Jan 1, 1958

By E. C. Weichel

THERE have been many attempts at permanent roof support in anthracite mines, in some cases brick arches, in others concrete, and also combinations of brick or concrete walls with steel beams. These supposedly permanent roof supports have frequently failed when heavy pressure is brought to bear upon the structure, because they are so rigid that failure occurs because the structure is unable to adjust itself to the increased load. Roof pressure exerts a tremendous weight, and it is at times difficult to find any means of support which is strong enough to bear the entire pressure, unless this supporting structure has in itself the element of some flexibility which will enable the structure to hold the moving mass until it "arches" itself. If the supporting medium has flexibility enough so that it can adjust itself to the heavy initial loads, and so give the overlying material an opportunity to form a self-supporting arch, then such a roof support will be more useful than any rigid roof support. There has recently been introduced into the anthracite region a new form of gangway lining that is flexible enough to slightly adjust itself under heavy pressures, and so give the loosened material which is being supported a chance to form into an "arched" mass. This lining, manufactured under patents granted to Hans Schaefer of Essen, Germany, was introduced in the United States in the summer of 1928, at which time the Amercan licensee, Richard Howells of

Jan 1, 1930

By L. W. Saperstein, Y. J. Wang

The development of computer programs to solve complex ventilation networks has reached a point of refinement where these programs become a necessary tool of the ventilating engineer. Such a program is presented. This program has an increased efficiency over its predecessors; it also includes the important facility of fixed quantity branches. This is in addition to the earlier capabilities of free-splitting, internal or external fans, and natural ventilation pressures. The program is written in Fortran IV with double-precision arithmetic and is listed here. Sample problems with input and output are also given. The recent, and presumably continuing, official interest in mine safety is bound to result in more stringent control requirements for ventilation. Anticipating this requirement, the Dept. of Mining, The Pennsylvania State University, has developed a computer program for the solution of complex mine ventilation networks. It is the opinion of this department that the program has sufficient merit to warrant its use in normal industrial operating conditions. Although the undergraduate mining engineering students of this department are routinely trained to use the program, it was felt that this training did not present a fast enough means of dissemination; consequently, this paper was written. The conception of the program is not new;1; however, the present version incorporates features that changes it from a scientific endeavor to a useful operating tool. These features include those of earlier programs, such as free-splitting, external or internal fans, and natural ventilation processes plus the important ability of handling fixed quantity branches, and of increased efficiency giving reduced cost. The facility for fixed quantities will be discussed in more detail. The solution of any network depends upon satisfying Kirchchoff's laws. These state that the sum of flow at any junction is zero, and that the sum of the pressure drop in branches totals the pressure drop in the mesh constituted by those branches, that is that the pressure drop around any mesh is zero. The terminology is derived from Synge," and is, in fact, that used by Topologists. A branch is any airway of uniform characteristics; a junction is where two or more airways meet (the minimum number of two airways is useful for describing the point where a low resistance airway changes into a high resistance one due to some physical constriction); a mesh is a path, along some branches, that returns on to itself, but does not need to traverse the same branch twice in order to do so; and a tree describes all those branches in a network which, while connected through all the junctions, do not form any meshes. Obviously the branches-in-tree are open-ended and can be shown to be one less than the number of junction (J-1). The branches-out-of-tree, also called basic branches, are equal to the number of basic meshes and are M = N — J + 1, where M is the number of meshes and N is the number of branches. The major difference between this network and an electrical one is that the law attributed to Atkinson for pressure drop is utilized rather than Ohm's law. Atkinson stated that the pressure drop (potential) is equal to a resistance factor multiplied by the quantity squared. This is written H = RlQlQ where H is the head loss. Q? is written in this factored fashion so that H will always have the same sign as Q. A negative sign is used to indicate that flow in a branch is opposite to that of its containing mesh. A mesh takes the direction of its basic branch. Utilizing Atkinson's law in Kirchchoff's second law and bearing in mind that the first law must remain satisfied, the program will determine all quantities, or head losses as they are related, for the branches of the network. The program uses a Geuss-Seidel form of in-teration, starting from an arbitrary Q and using a correction factor of the type first suggested by Professor Hardy Cross' that will handle the nonlinear equation of Atkinson's law. A fuller description of the interative process is included in Wang and Hartman.' Iteration continues until the correction factor is less than or equal to a preset error (E) or until a maximum number of iterations (MAXIT) have been reached. Utilizing an E of 50 cfm, sample problems have had rapid solutions. Rapidity of solution is also ensured by the method of selecting meshes and basic branches. This is done by the computer, which chooses the highest resistance branches, fixed quantity branches, and those containing fans, as basic branches. Natural ventilation pressures are handled as fans of constant pressure and may be assigned to any branch. The computer will generate a fan characteristic by polynominal fitting if a few operating points from the desired fan are input. A fan may be placed in any branch of the network, except those with fixed quantities. The strength of the present program over its earlier versions is its ability to handle fixed quantity branches. This means that certain branches can have their quantity determined, or preset, by the ventilating engineer. Operating under this constraint, the program will analyze the network and output the pressure change necessary to achieve this desired quantity. A call for positive head loss would require an auxiliary fan; negative head loss would require a regulator. This represents a powerful tool for the ventilating engineer who must insure that certain quantities of air pass across the operating faces or through working stopes. McPherson6 suggested that a ventilation program would be useful for determining in advance which branches were receiving inadequate air, and that subsequent calculations would then indicate the necessary corrections. The present program makes these corrections. Thus the mine manager can know immediately the consequences of changes to his system;

Jan 1, 1971

By G. Thodos, R. J. Smialek

A method has been developed that permits the correlations of Mehra and Thodos8 and Dastur and thodos2 for binary systems to be used for the prediction of the vapor-liquid equilibrium constants of the light and heavy constituents, Kland Kh, of a ternary hydrocarbon mixture. Furthermore, the unique relationship observed in this study, i.e., a plot of log Ke/Ki vs log Kp/K h is linear and passes through the origin, permits the calculation of the K-value for the intermediate component. This approach has been used to establish K-values for the constituents of the three ternary hydrocarbon systems used to develop this method and has also been applied to two additional ternary hydrocarbon systems to yield an average deviation of 7.7 per cent resulting from a total of 294 points for the five ternary systems considered. INTRODUCTION The rigorous calculation of vapor-liquid equilibrium constants for systems containing two or more components is a difficult problem and becomes extremely complex at elevated pressures and for conditions approaching the critical point. Although thermodynamic relationships can be developed to account for the vapor-liquid equilibrium behavior of simple systems, their use is limited because the necessary PVT data for these systems are not generally available. To establish a method for calculating K constants directly, without any recourse to the PVT behavior of a system, Mehra and Thodos8 applied the principle of corresponding states to the vapor-liquid equilibrium constants of binary hydrocarbon systems. They developed a series of charts which made possible the prediction of K-values for all binary hydrocarbon systems not containing methane. This work has been extended by Dastur and Thodos2 to include binary hydrocarbon systems containing methane. The charts developed in these two studies cover the high-pressure region and are applicable to conditions in the vicinity of the critical point. The ability of this approach to predict vapor-liquid equilibrium constants of binary hydrocarbon systems suggests that this method may be extended to the prediction of the K-values of the components of ternary hydrocarbon systems. In this investigation, the charts developed for both the methane and non - methane binary systems,2,8 together with mixture rules developed in this study, have been used to predict the K-values of the light and heavy components of a ternary hydrocarbon system. These calculated values are then used to establish the K-value of the intermediate component through the use of a novel relationship developed in the present study. DEVELOPMENT OF METHOD FOR PREDICTING K-VALUES OF TERNARY SYSTEMS The application of the corresponding state charts developed for binary hydrocarbon systems is restricted to those systems containing two components. The extension of these correlations to three-component systems requires that the ternary system be reduced to an equivalent binary, which can be treated in a manner consistent with the corresponding state development. To establish such an approach, the vapor-liquid equilibrium constant of the light component K is first calculated by assuming that the ternary mixture consists of the light component and a pseudo-heavy component of the intermediate and heavy constituents of the original ternary. To establish the vapor-liquid equilibrium constant of the heavy component Kh, the light and intermediate constituents of the ternary are combined to form a pseudo-light component of another equivalent binary system. The calculated values Kl and Kb are then utilized to calculate the vapor-liquid equilibrium constant of the intermediate component EQUILIBRIUM CONSTANT FOR LIGHT COMPONENT K To calculate the K value of the light (most

Jan 1, 1965

By GUY C. RIDDELL

ZINC, manganese, and aluminum received attention at the two nonferrous metallurgy sessions at the Annual Meeting. L.P. Davidson, general superintendent of the rebuilt Monsanto zinc plant, described its operation, which reflects Polish practice and is really a combination of electrolytic, Waelz, and retort procedure. Briefly, it embraces leaching of roasted concentrate with sulphuric acid, electrolysis of sulphate solution using Tainton lead-silver anodes with ?goulac? added to the electrolyte, treatment of tailing in Waelz kilns, and retorting of the recovered zinc oxide, casting furnace dross and residues. Recovery is good, equipment and maintenance costs low. Ferrate zinc that might be lost in the electrolytic process appears to be recovered as oxide in the Waelz treatment.

Jan 1, 1942

By D. H. Thompson, A. W. Tracy

E. A. ANDERSON*—At the outset, I note that you are using a humid atmosphere containing ammonia but that you make no reference to the variable of carbon dioxide content. Edmunds in his work in this laboratory found very marked effects on the rate of failure due to variations in carbon dioxide in the environment. This point is, of course, strongly related to the overall corrosion rate problem since the role of the carbon dioxide seems to be to permit the formation of hygrogroscopic salts which give a controlled moisture film on the specimen surface, which in turn seems to support the intergranular penetration more consistently than would otherwise occur. (2) Your results with various copper binary systems are very striking. It is curious, however, that the time-to-failure minima all occur at percentages of the alloying element which are considerably below the solubility limits as given in the conventional equilibrium diagrams. If your theory regarding the presence of these impurities in some concentration in the grain boundaries is correct, then either the existing diagrams are not accurate in the room temperature region, or there is a difference in solubility in the grain boundaries as compared -with the grains. A study along these lines might be very revealing. (3) The undesirable effect of silicon in copper calls to mind our own observations on the influence of silicon on the stress corrosion cracking resistance of alpha brass. In this case, silicon was found to have a very marked beneficial effect, particularly when a heat treatment capable of producing a grain boundary constituent was used. I should appreciate it if in the discussion of your paper this point should arise, you would attempt to clarify the difference between the copper-silicon binaries and the copper-zinc-sili-con ternary alloys. D. H. THOMPSON and A. W. TRACY (authors' reply)—(1) We have no data on the constancy of the carbon dioxide content of the air used for the test atmosphere but have believed that the normal carbon dioxide content of the air was as constant as could be obtained by using Edmunds' method of removing carbon dioxide from the air and then adding a measured quantity. In any event, the test atmosphere was the same for all specimens in a test run. We agree with Mr. Anderson that the carbon dioxide content is important in the formation of a hygroscopic film on specimens. (2) We can imagine that there could be a concentration of solute atoms at the grain boundaries which would be so small that present methods would not detect it even if it exceeded the solubility limit of the alloy. There could be somewhat greater solubility at the grain boundaries for an interstitial solute. There is a possibility that phosphorus dissolves in this way but we believe that none of the other solutes studied does. In our present studies we hope to find out something about conditions at the grain boundaries of some of the systems mentioned in the paper. (3) Mr. Anderson points out that silicon brass, which has had a high temperature heat treatment followed by a quench. is highly resistant to stress-corrosion cracking. Although the test conditions used by Anderson* et al were different from our test conditions, it is noted that the silicon brasses which had not had the special heat treatment were less resistant to stress-corrosion cracking than copper containing approximately equal amounts of silicon. G. R. GOHN†—Nonferrous metallurgists and particularly, materials engineers, have been accustomed to thinking

Jan 1, 1950

By d&apos, K. Mukherjee, C. R. Antonio, R. J. Maciag, G. J. Fischer

Tensile data indicate that over the range of strain rates 10-5 to 10-1 sec-1 and in the temperature range 298° to 743°K the flow stress at a given temperature may be expressed as: C0 = Cem where m changes abruptly at a critical strain rate of 10-2 sec-1. The Zener-Hollomon parameter was tested and found to be invalid except at temperatures exceeding 700° K. Values of AH calculated for temperatures above 700°K ranged from 30 to 47.5 kcal per g-mole. ThE flow characteristics of aluminum and aluminum alloys as a function of temperature and strain rate have been of interest to various experimenters for many years. Trozera et al.1 determined tensile flow curves for pure aluminum and concluded that the combined effect of temperature and strain rate on the flow stress could be related using the Zener-Hollomon parameter. More recently, Hockett2 proposed a relationship between compressive flow stress, temperature, and true strain rate which could be represented by a surface. Holt et al.3 studied strain rate effects on flow stress in a number of aluminum alloys at room temperature. It was determined that there is a critical strain rate above which a strain rate effect is observed. It was also reported that the strain rate sensitivity was significant in aluminum alloys in the "0" condition only. In a recent review paper McQueen4 has considered a number of mathematical expressions which have been used to describe the relationship between stress, strain rate, and temperature. These expressions have been applied to the flow characteristics of a number of different metals and alloys including aluminum. In the present work the strain rate sensitivity of 7075-0 aluminum was determined in the temperature range of 298° to 743°K. The tensile flow stress at 0.2 pct offset was obtained over a nominal strain rate range of 10-5 to 10-1 sec-1. EXPERIMENTAL Threaded tensile specimens were cut from a single heat of 7075-T6 aluminum. The composition of this heat is given in Table I. The test bars had a gage section 1.5 in. long by 0.250 in. diam and conformed to ASTM specification E-8-57T. After machining, the bars were annealed at 413° ± 10°C for 2 hr. They were then cooled to 260°C in 3 hr, and finally air cooled to room temperature. This treatment is commonly used to produce the "0" condition. Load-time curves at constant crosshead speeds were obtained at various temperatures using an Instron testing machine. Crosshead speeds ranged from 0.002 to 40 in. per min. A three-zone resistance tube furnace was used for the elevated-temperature tests. Temperatures were measured at three points along the gage length by means of suitably placed thermocouples. Each tensile bar was held at temperature for 30 min prior to testing and the maximum temperature variation along the gage length was kept below 1°C. In all, 275 samples were tested and each data point plotted is an average of at least two tests. In many cases the point represents up to six tests. RESULTS AND DISCUSSION Values of the flow stress at 0.2 pct offset at six different temperatures are plotted vs strain rate on log-log coordinates in Fig. 1. Over discrete ranges of strain rate, the data for each temperature fit the expression:

Jan 1, 1969

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

John G. Tripp-—The concept of converting fuel deposits in-situ to useful forms of energy and chemical raw materials has important possibilities as a means of stretching out our fuel resources. The authors have worked in this field for years and in fact are among the pioneers in developing in-situ techniques based on underground electrocarbonization. Their efforts have aroused great interest in this subject and their contributions will undoubtedly gain even more significance as time goes on. The 4 to 5 billion tons of petroleum are proved reserves, that is, they are completely defined and could be produced economically with present methods of recovery. Reserves of coal, tar sands, and oil shale shown in Table I are not equivalent to proved reserves as the term is used in the oil industry. Incidentally, the 4.3 billion tons of oil shown in the tabulation is equal to about 28 billion barrels of oil and, therefore, presumably does not include reserves of natural gas liquids estimated at about 5 billion barrels. The relative comparisons would be more complete if these liquids together with the reserves of natural gas were included in the tabulation. It is stated in the report that production costs of the order of 10c per million Btu's could be expected from a large industrial electrocarbonization installation. The authors state that the operation probably could be operated successfully and at a profit. I would like to express my view that for the operation to be profitable extremely favorable conditions would have to prevail. For example, the coal seam would have to be thick and close to the surface in order to minimize drilling costs; the deposit should be dry and so situated that there would be little, if any, inflow of ground water; and the seam would have to be relatively gas tight to avoid excessive gas leakage. Notwithstanding the tremendous strides that have already been made, it is my hope that the authors plan to continue their development work. Experiments on underground electrolinking and initial carbonization at Gorgas, Ala., indicate a need for improved control over the operation. Subsequent examination of the underground system at Gorgas has shown that the gasification zone did not always follow a direct path between the electrodes. Undoubtedly the control of the in-situ thermal processes can be improved by further development work. With respect to the electrocarbonization of oil shale it may be well to point out that the cost of mining oil shale is estimated to be 50c to 60c per ton. These are low mining costs as compared to coal. Thus it would appear that there is less economic incentive for applying in-situ thermal methods to oil shale than there is for applying these methods to coal. As is the case with in-situ methods for petroleum, the product from the shale having the most economic interest would be liquid oil rather than gas. The authors point out that for distances up to several hundred miles it is cheaper to transmit energy as electricity than it is to ship energy as coal. This is a very important point, and with coal shipping rates rising periodically, it could prove increasingly important in the future. I believe that the authors deserve great credit for their outstanding work on underground electrocarbonization. The knowledge resulting from their efforts is of great value to our fuels technology. James L. Elder—The experimental work conducted by the authors on the electrolinking-carbonization of carbonaceous materials in situ is of great interest. The method is of great importance in the development

Jan 1, 1955

By Hans Lundberg

AFTER the war years, great activity has been shown in geophysical exploration for ore. The appreciation by mining and government geologists of geophysical techniques and results is largely responsible for the popularity of these methods. In Canada, plans are being made to study, by geophysical methods, the structure of a portion of the Pre-Cambrian shield in the hope that such studies will not only give a clearer picture of the geology, but will be of direct aid to the mining companies when selecting areas for detailed prospecting. Although geophysics thus has become more popular, some engineers are still reluctant to employ the methods to their full extent. Allotted funds are often rather low, so that the least expensive

Jan 1, 1947

By B. Haimson, C. Fairhurst

A criterion is Proposed for the initiation of vertical hydraulic fracturing taking into consideration the three stress fields around the wellbore. These fields arise from (1) nonhydrostatic regional stresses in earth, (2) the difference between the fluid pressure in the wellbore and the formation fluid pressure and (3) the radial fluid flow through porous rock from the wellbore into the formation due to this pressure difference. The wellbore fluid pressure required to initiate a fracture (assuming elastic rock and a smooth wellbore wall) is a function of the porous elastic constants of the rock, the two unequal horizontal principal regional stresses, the tensile strength of the rock and the formation fluid pressure. A constant injection rate will extend the fracture to a point where equilibrium is reached and then, to keep the fracture open, the pressure required is a function of the porous elastic constants of the rock, the component of the regional stress normal to the plane of the fracture, the formation fluid pressure and the dimensions of the crack. The same expression may also be used to estimate the vertical fracture width, provided all other variables are known. The derived equations for the initiation and extension pressures in vertical fracturing may be employed to solve for the two horizontal, regional, principal stresses in the rock. INTRODUCTION Well stimulation by hydraulic fracturing is a common practice today in the petroleum industry. However, this stimulation process is not a guaranteed success; hence, the deep interest shown by the petroleum companies in better understanding the mechanism that brings about rock fracturing, fracture extension and productivity increase. Geologists and mining people became interested in hydraulic fracturing from a different point of view: the method may possibly be employed to determine the magnitude and direction of the principal stresses of great depth. Numerous articles in past years have dealt with the theory of hydraulic fracturing, but they all seem to underestimate the effect of stresses around the wellbore due to penetration of some of the injected fluid into the porous formation.1-4 Excellent papers on stresses in porous materials due to fluid flow have been published5,6 but no real attempt has been made to show the effect of these stresses in the form of a more complete criterion for vertical hydraulic fracturing initiation and extension. This paper is such an attempt. ASSUMPTIONS It is assumed that rock in the oil-bearing formation is elastic, porous, isotropic and homogeneous. The formation is under a nonhydrostatic state of regional stress with one of the principal regional stresses acting parallel to the vertical axis of the wellbore. This assumption is justified in areas where rock formations do not dip at steep angles and where the surface of the earth is relatively flat. This vertical principal regional stress equals the pressure of the overlying rock, i.e., S33 = —pD, where S33 is the total vertical principal stress (positive for tension), p is average density of the overlying material and D is the depth of the point where S33 is calculated. The wellbore wall in the formation is considered to be smooth and circular in cross-section. The fluid flow through the porous elastic rock obeys Darcy's law. The whole medium is looked upon as an infinitely long cylinder with its axis along the axis of the wellbore. The radius of the cylinder is also very large. Over the range of depth at which the oil-bearing formation occurs, it will be assumed that any horizontal cross-section of the cylinder is subjected to the same stress distribution, and likewise that it will deform in the same manner. STATE OF STRESS PRIOR TO DRILLING OF WELLBORE At a depth D from the earth surface within the oil-bearing strata, it is assumed that the following are 1References given at end of paper.

By H. Doi, Y. Fujiwara, K. Miyake

In order to throw light on the mechanism of plastic deformation of WC-Co alloys, compressive tests of WC-(7 to 43) vol pct Co alloys have been carried out at room temperature, and stress-micro strain relation has been investigated in detail. The analysis of the factors affecting the yield stresses reveals that the yield stresses can be predicted by modified Oro-wan's theory if one properly estimates the planar in-terfiarticle spacings. Conzpressive straining of some of the alloys by 0.066 to 0.17pct increases the decrements by a factor of as much as 3.4 to 14, whereas the corresponding increase in the electrical resistivities is less than 10 pct. The analysis of the decrement data in terms of -Gramto and Lücke theory shows that the marked increase is attributed to increased dislocation darnping itt the binder (cobalt) phase. By cornbilling the decrement data and the conzjwession duta, one obtains the relation between flow stress in shear (?t) and increase in dislocation density (p): At = const . v6 . This is interHeted to mean that the mechanism of strain hardening of CirC-Co alloys is essentially sarne as the one for dispersion strengthened alloys. The possible effect of bridge formations between the carbide particles has also been examined. OWING to the combination of hardness, strength, and other physical and chemical properties, WC-Co alloys have opened the way for unique fields of applications, the recent ones being, for instance, anvils for super-high-pressure generation apparatuses. In such applications, the alloys are frequently subjected to very high compressive stresses: these stresses may cause the alloys to deform plastically and eventually to fail. However, much remains obscure regarding the nature of the plasticity of the alloys. Evidently, the alloys owe their high strength to the hard carbide particles which frequently occupy as much as 80 to 90 pct in volume fraction, whereas the ductility required for practical applications is provided by the small amount of the binder phase between the carbide particles. When the volume fraction of the carbide phase is not very large, deformation behavior of the alloys may be described by some of the current dispersion strengthening theories. However, greatly increasing the carbide phase is thought to lead to some carbide skeleton structure or bridge formations owing to the increased chances for direct contacts between the carbide particles;1,2 this may appreciably affect the plasticity of the alloys. Regarding the effect of formation of the carbide skeleton structure, it is interesting to note the work by Ivensen et al.3 on compression tests of the alloys containing somewhat large carbide particles; they observe extensive generation of slip bands in the carbide particles after application of some preliminary compressive stresses. They interpret the results in terms of plastic deformatiot: of the carbide particles which are supposed to have formed a skeleton structure; the binder phase plays only a passive role, at least in the early stages of the deformation. That carbide crystals exhibit microplasticity at room temperature is apparent from the work of Takahashi and Freise4 and French and Thomas5 on indentation of WC single crystals. On the other hand, Dawihl and coworkers6-10 maintain that even when volume fraction of the carbide phase is very large (for instance, more than 90 pet), a very thin binder layer generally exists between the carbide particles. They interpret the results of the extensive mechanical tests in terms of the plasticity of such a layer. Gurland and Bardzil11 point out that decrease in ductility of the alloys with increase in the carbide phase is caused by the effect of plastic constraint exerted by the dispersed carbide particles. Drucker12 further develops this concept from a continuum-mechanics approach on an assumption that a continuous thin binder layer separates the carbide particles. A common feature of the studies reported so far on the plasticity of the alloys is that the information deduced is invariably qualitative in nature. Thus, very few systematic experiments for obtaining reliable and sufficiently detailed stress-strain curves of the alloys varying widely in the microstructural features have been carried out. In particular, it may be of special interest to investigate in detail the early stages of the plastic deformation of the alloys in order to shed light on the strengthening mechanism. However, such work appears to be extremely rare. Doi et al.13 recently reported a first brief account of the results of some quantitative analysis of the plasticity of the alloys in terms of dislocation theory. Their experiment was rather limited in the composition range covered (volume fraction occupied by the carbide phase: 79 to 83 pct), and thus they could not necessarily elucidate the controlling mechanism of plastic deformation of the alloys of a more general composition range. Consequently, in the present investigation, deformation behavior and some other physical properties of the alloys were investigated and discussed in more detail over a much wider composition range. SPECIMEN PREPARATION WC-Co alloys used in this experiment were prepared in cylindrical or rectangular form by sintering in vacuo compressed mixtures of tungsten carbide and cobalt

Jan 1, 1970

By K. Prins

ONE of the more pressing problems faced by the coal industry today is the development of adequate means for meeting conservation laws, particularly those involving stream pollution, in various parts of the country. Discharge of dirty coal washery water into streams and rivers is almost universally frowned upon. Many states have enacted laws carrying heavy fines to curb the practice. The Prins stream-cleaner is one of the latest machines to enter the market. It is closely related to the cyclone thickener in principle. Eleven stream-cleaners are currently operating, ranging in size from 4 to 16 in. diam. In more recent installations the water enters directly in line and on a tangent with the impeller. The impeller consists of a vertical shaft up through a packing gland and bearings, and a V-belt pulley. The lower part is a tubing fastened to the shaft above, extending through the water intake compartment and provided with six vertical flat bars welded to the tubing. Portholes are situated in the upper end of the tubing, immediately below the point where shaft and tubing join together. The portholes are placed so that they are in open communication with the upper compartment of the stream-cleaner from which the processed water is discharged. The impeller is motor driven with a wide range vari-pitch drive employed between motor and impeller. The motor is mounted vertically, and the mounting provided with a vertical hinge allowing for needed adjustment of the wide range vari-pitch drive. The dirty coal washery water entering the machine under 20 lb psi pressure, flows from the compartment above the impeller, between the impeller blades, and is whirled around in the vertical section of the impeller enclosure. The speed of the impeller supplies centrifugal force and velocity required for separating suspended solids from water. The lower part of the machine consists of a cone, whose action is similar to other machines of the same type. The underflow discharge orifice is a cold rolled steel block machined to correspond with the cone angle and allows insertion of steel tubes of different diam. On 16 in. machines a 1 ¾ in. ID vertical discharge pipe is used. Provision is made for attaching a curved section of the same diam to the vertical pipe, to which, in turn, different lengths of horizontal pipe can be connected. Curved Pipe Advantageous It has been found that a curved pipe offers resistance to discharged material flow. In addition, the rotary motion of the underflow can be easily arrested in a curved pipe. Impeller speed of the 16 in. diam machine is provided from 400 to 800 rpm. A speed of about 474 rpm is suitable for maintenance of a constant underflow in coal slurry. In one installation 5x ¼ in. coal is cleaned in a Jeffrey Baum type washer at a 225 tons per hr rate. Washer installation is of the conventional type and a drag type sludge tank is used for water clarification purposes. Capacity of the water system, including the Baum washer, is about 40,000 gal. Before placing the stream-cleaner in operation, it was necessary to flush out the entire system every five days of two shift operations. The only time the system is drained now is for repair work on the sludge conveyor or the rig. The suction line of the stream-cleaner pump terminates in a number of small branch lines located at a depth of about 4 ft above the sludge conveyor. Each branch line extends the full width of the tank and is provided with four intake ports, each one with a funnel shaped inlet projecting downward. The arrangement provides an extensive pick-up area, for dirty water, and the inlets are arranged for a low rim velocity, preventing the taking in of coarse particles. The funnels are also arranged to extend up or down in the tank. They are set to pick up -60 mesh material exclusively.' The material is a high ash and high sulphur product and thus has to be disposed in the refuse conveyor. The underflow of the stream-cleaner is discharged on top of the washery refuse which is carried in a drag type horizontal conveyor, discharging into another refuse conveyor inclined at 30º with a short horizontal loading section. Some Disadvantages The impeller inherits certain disadvantages because of the nature of its construction. Additional moving parts make it subject to wear and maintenance costs. The advantage of being able to maintain a constant speed, however, to produce desired water velocity in the machine outweighs the drawbacks. Better separation between water and solids can be obtained by regulating time of residence of water through adjustment of valves in the intake and discharge lines. The amount of fines encountered during plant operation will vary because of higher or lower moisture in coal passing over fine coal vibrating screens. Even the amount of fines picked up by underground loading machines will be inconstant. Consequently, the percentage of solids will vary in water to be processed. The velocity in the feedlines to the slurry thickeners will fluctuate, with the required water velocity lacking. Another advantage advanced for the machine is its ability to operate on 15 to 25 lb line pressures at the water intake, reducing pump power required and pump maintenance.

Jan 1, 1952

By R. E. Reed-Hill

A simple accurate graphical method for orienting fcc crystals using (111) slip traces on a single surface is described. Solutions placing the pole of the surface in a unit stereographic triangle are obtained using a Wulffnet, a (111) standard projection showing the four (111) planes, and a (111) standard projection ruled into unit stereogmphic triangles. The multiplicity of solutions is described in relation to this method. AN accurate, rapid single-surface technique for orienting fcc crystals, using (111) slip or twin traces, has been a matter of continuing interest, as evidenced by the periodic appearance of papers on this subject.'-4 This note presents a new method possessing some advantages over those previously reported. It is an analog to the technique for hcp metals5 where the solution is based upon a stereographic rotation of the specimen surface on a (0002) standard projection that contains the planes of the possible features that might account for the observed traces. In the hexagonal solution, the axis of rotation is the basal-plane trace in the surface. In the fcc case, the axis of rotation is one of the observed ( 111) slip or twin traces. It has been observed that the solution is greatly facilitated if the indicated movements of the (111) traces during the rotation of the surface are plotted directly on a paper copy of a Wulff net as shown schematically in Fig. 1. The trace selected to represent the axis of rotation is assumed to fall at the north-south poles of the Wulff net. The directions of the other traces are then plotted as points at the proper angles around one-half of the basic circle of the net. The loci of points corresponding to the movements of these traces (directions) during a 90-deg rotation of the surface, about the polar axis of the net, are then easily and accurately drawn by following the appropriate small circles on the Wulff net. The solutions to the problem are obtained with the aid of a (111) standard projection of the (111) planes, see Fig. 2. This is normally a Xerox copy of a carefully drawn master made on high-quality tracing paper. The (111) standard projection is superimposed over the Wulff net and rotated about its center until the points of intersection of the loci of surface traces, drawn on the Wulff net, and the great circles representing the (111) traces, all lie along a common meridian of the Wulff net as demonstrated in Fig. 3. This latter great circle represents a possible position of the surface. The pole of this plane is then plotted on the (111) standard projection. Its location in a unit stereographic triangle may be readily obtained by superimposing (over the standard projection) another tracing paper (111) standard projection subdivided into unit stereographic triangles. The result of this last operation is shown in Fig. 4. MULTIPLICITY OF THE SOLUTIONS The maximum possible number of (111) traces on a single grain surface is four. Any one may be selected as the axis about which the surface is rotated. Corresponding to each such choice are three possible surface-pole orientations, related to each other by a simple 120-deg rotation about the pole of the (111) basic circle. This is a direct result of the threefold symmetry of the (111) standard projection. Since each of the four rotations will normally give a different set of three-pole positions, there are, accordingly, twelve possible solutions. Each of these twelve solutions places the surface pole in the same relative position in a stereographic triangle so that all are crystallo-graphically equivalent. Accordingly, only a single solution is required to obtain a basic orientation of the crystal. It should be noted, however, that the orientations obtained by reflecting* any of these twelve orien- *The reflected orientations may be obtained by a 90-deg rotation of the opposite sense to that shown in Fig. 1. This rotation places the correspond-ing trace loci in the lower hemisphere of the Wulff net rather than in the upper hemisphere. tations through the surface are also possible orientations that could account for the surface traces. Thus, a given set of four traces always corresponds to a pair of basic orientations related by reflection through the specimen surface. This ambiguity can only be re-

Jan 1, 1967

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood's interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood's8 observations as confirmation of Leigh's14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh's analysis. Ellwood's clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood's method of specimen preparation (casting followed by wrought fabrication) and alternativ'e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a' during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By C. S. Matthews, H. C. Lefkovits

Drilling progress is often delayed by sticking of the drill string. The development of preventive and remedial methods has been hampered by incomplete understanding of the sticking mechanism. A recent lahorntory investigation hns indicated that one type of sticking may be attributed to the difference in pressure between the borehole and formation. This paper shows, by means of soil mechanics, that the primary cause for differential pressure sticking is cessation of pipe movement, whereas diflerential pressre and stanrtding time determine the severity of the sticking. The analysis stresses the importance of using low-weight muds with low solids content and low water loss to alleviate diflerential pressure sticking and describes why packed hole drilling, long strings of drill collars, and a large deviation from the vertical are conducive to sticking. Finally, preventrve and remedial methods ore evaluated, and a theory is presented on the release of stuck pipe by spotting oil. INTRODUCTION Since drilling with long strings of oversize drill collars has become standard practice in many areas, the incidence and severity of the stuck pipe problem has increased. It has been noticed that in the majority of these cases the sticking could not possibly be attributed to key seating or caving of shales. It appeared that, due to the differential pressure between the mud column and the formation fluid, the collars were pressed into the wall and so became "wall stuck". Points to note about differential pressure sticking are: (1) sticking is restricted to the drill collars, (2) the collars become stuck opposite a permeable formation, (3) the sticking occurs after an interruption of pipe movement, (4) circulation, if interrupted, can be restarted after the sticking is noticed, and (5) no large amounts of cuttings are circulated out after restarting circulation. Helmick and Longleyl investigated pipe sticking by differential pressure in the laboratory and found an empirical relationship between the differential pressure, the sticking time and the required pull-out force. In this paper an explanation of the mechanism is given based on Terzaghi's theory of clay consolidation. A qualitative description is given in the following paragraphs while the derivation of fonnulas is given in Appendices. This paper is a first attempt to explain pressure differential sticking and many points will require additional theoretical and practical investigation before the problem can be fully understood. PRESSURE DIFFERENTIAL STICKING AS A CONSOLIDATION PROBLEM In any borehole, where the mud pressure is higher than that exerted by the formation fluids, a mud cake is formed opposite the permeable sections of the hole and a continuous flow of filtrate takes place from the mud, through the cake and into the formation. This radial flow pattern requires a certain distribution of the hydraulic and the effective (grain-to-grain) stresses inside the mud cake. Any quantitative or qualitative change in the external pressure conditions will produce a change in the flow pattern and, consequently, also in the internal stress distribution inside the cake. In view of the low permeability and the high compressibility of a clay mud cake, the adjustment of the internal stress distribution is slow and is accompanied by a change in volume. Time dependent stresses are thus created which gradually diminish as the new state of equilibrium between internal and external pressures is approached. Some 30 years ago, Terzaghi developed his "Theory of Consolidation" to account for the time-dependent stresses and settling of clay formations under the influence of external loads. He derived a differential equation by which the time-dependent hydraulic stress and the consolidation can be computed for any point inside the layer during the consolidation process. His theory is based on the assumption that the change in stress is solely due to a change in water content and it may only be applied to one-dimensional consolidation phenomena. Other investiga-tors5,10 have expanded his theory to include processes of more than one dimension. The difference between the external pressures on the mud cake before and after sticking is a qualitative one (isolation of part of the cake by the static contact with the drill collars after pipe movement has been stopped)', and the time-dependent stresses thus created may be investigated by means of Terzaghi's theory. By this analysis the changes in the nature of the contact surface between the drill collars and the mud cake during the sticking can be explained; and the friction force between the two may be computed as a function of the sticking time, the borehole dimensions and the mud cake characteristics.