Search Documents

By T. J. Neil, C. B. Manula, O&apos

This paper describes a simulation model developed to analyze truck haulage problems as they are found in the open pit mining and construction industries. The model, using a computer, cycles trucks between their assigned loading and discharge points over a measured haulage route. Required parameters for model operation include the number and type of operating trucks and loading units, maximum truck acceleration and velocity, a realistic vehicular deceleration rate, and the ratio of ore to total material loaded at each origin. Equipment performance characteristics, system profile characteristics, and service time distributions are also included. Records are kept of all waiting times at the loading and discharge points and of any truck interference on the haulroads (moving queues), and a current journal of ore and waste production is maintained. In the pursuit of reduced truck haulage costs, management is confronted with three particular problems in truck and shovel mines. 1) What is the best assignment of trucks to shovels in the system? 2) If new equipment is needed, which new shovels and trucks will operate most effectively in the system? 3) Are any physical changes in the haulage layout warranted to increase productivity? For small open-pit mines the answers to these questions may be obvious. However, for larger operations complex problems are encountered with production and system configuration relationships usually being unknown. The mining simulator discussed here was developed to aid management in evaluating alternative pit-haulage schemes to reduce the risk involved in the selection and assignment of equipment in open-pit truck and shovel mining systems. There are two fundamental differences between this model and other truck haulage simulators: one is a difference of degree, the other a difference of kind. This model can simulate more complex systems than previous models by allowing transportation of material from multiple mine faces to multiple mine destinations and by being readily adaptable to a wide variety of mine layouts. The second difference that characterizes the model is the standard simulation of truck movements. This technique enables each vehicle to perform according to its mechanical capabilities and the physical profile of the haul road. Among the similarities between other truck haulage simulators and this model are the recognition of the probabilistic nature of certain service times in the system and the use of a digital computer to operate the model. The computer inherits the staggering computational and bookkeeping work loads and provides a means for compressing the time scale by allowing several days' operations to be simulated in a matter of minutes. DISTRIBUTION SYSTEM Basic aspects of the system analyzed here may be brought into focus by referring to Fig. 1, a schematic of the typical open pit truck-shovel operation programmed into the simulation model. A single stage materials handling scheme is employed to transport both ore and waste. Loaded trucks are directed to a crusher or stockpile if ore is being mined, while overburden is conveyed to a waste dump. Each shovel has a given number of assigned trucks and has two associated haulage routes, one for waste and one for ore. Up to 5 shovels and as many as 10 trucks per shovel (or a total of 50 trucks) can be operated in the model. Essentially the model, using a computer, cycles trucks between their assigned shovels and the proper discharge points over measured haulage routes. Required input parameters for model operation include the number of shifts to be simulated, operating time per shift, number and type of operating trucks and shovels, maximum truck acceleration and velocity, a realistic vehicular deceleration rate, and the ratio of ore to total material loaded at each shovel. Equipment performance characteristics, system profile characteristics, and service time distributions are

Jan 1, 1968

By H. H. Rachford, D. S. Howard

In the withdrawal of fluids from tilted aquifers it is of value to be able to predict pressure patterns during the course of the pressure decline. As an example of this, in the displacement of fluids from oil reservoirs being produced by water-drive, prediction of the reservoir pressure is an important factor in fixing production rate. The prediction of pressure patterns in the depletion of an inclined aquifer has conventionally been made by solving the well known flow equations for the pressure Patterns in a horizontal aquifer, and correcting these patterm for the pressure difference due to the hydrostatic head associated with the vertical distance between a point in the horizontal aquifer and the corresponding point in the tilted aquifer. Inasmuch as the equation describing flow in tilted strata is different from that for horizontal flow. there was question as to the validity of the simple corrective procedure current1y in use. To examine the magnitude of error made using this procedure, an inclined aquifer was chosen for which the error was expected to he large, and the equation for flow in this tilted stratum was solved numerically. The results of the conventional procedure of correcting the solution of the equation for horizontal flow was compared with the solution of the correct equation by studying the difference between predicted pressures by the two methods. Three forms of the hydrostatic head correction were studied. The results for all three forms of the head correction are similar. The error in the approximate solution is quite dependent on the position of the horizontal aquifer with respect to the inclined one. The error is greatest at the producing end ad increases with amount of fluid withdrawn. The magnitude of the errors is not large if a good choice is made for the position of the horizontal datum. The most satisfactory position for the datum in all cases is near or slightly about the mid-point of the inclined stratum. Use of the best approximate method studied with the best datum tested yielded predicted pressures in error no greater than 7 psi. INTRODUCTION The movement of water by expansion from an aquifer to displace fluids from a contiguous oil reservoir was first recognized over 20 years ago.9 Since that time much work has been done to relate this mechanism to reservoir behavior mathematically. The result of this effort on the part of many workers has led to an understanding of underground fluid movement which has enabled us to follow and predict the behavior of the water-drive reservoir. One reason that good progress has been made in the application of mathematics to the study of pressure patterns and water movements in aquifers has been that the differential equation which describes this process is of a relatively simple form. The equation for the isothermal, horizontal, viscous flow of water through homogeneous sandstone is identical with that for the diffusion of heat through homogeneous solids, and this equation and means of obtaining solutions for it with many types of boundary conditions have been studied extensively. That this work has been highly successful is clearly emphasized by the large number of solutions developed for problems of interest both by methods of formal mathemat-

Jan 1, 1957

By W. R. Foster, J. M. McMillen, A. S. Odeh

The complete equations of average linear momentum balance for a single-phase fluid in an incompreisible, homogeneous, porous medium are derived. The derivation begins with Euler's equation of motion for a continuum and uses an integral transform recently developed by Slattery. 7 For steady flow of a compressible, Newtonian fluid, the usual equations of motion result. For transient flow, the space-time description of the pressure is determined in the lowest approximation by the telegrapher's equation. From the analysis a new phenomenological coefficient results which connects the viscous traction to the deriv ative of the linear momentum density. The magnitude of this coefficient determines the velocity of sound through the pore structure in this approximation to the pressure field. INTRODUCTION The modification of Darcy's law of momentum balance for steady, single-phase flow through porous media has been discussed for many years. The first modification was suggested by Forcheimerl who added terms of higher order in the velocity. These can be expected to appear because the underlying microscopic equations of momentum balance are themselves nonlinear in the point velocity field. The Reynolds tensor pvv, which represents the convective flux of momentum density, appears in the momentum balance equation. Only in rectilinear flow (parallel stream lines) does the divergence of this tensor vanish. Since the steady flow stream lines in most porous media are not parallel, nonlinear dependence of the pressure gradient on the velocity should naturally appear. This nonlinearity has nothing to do with turbulence in the ordinary sense of random fluctuations in the pressure and velocity fields. It arises simply because the stream lines converge and diverge, even for steady flows. Klinkenberg2 demonstrated that the permeability coefficient in Darcy's law depends on the absolute pressure or, alternatively, on the density field. However, because he neglected inertial terms of the Forcheimer type, his correction coefficient could not be represented by a constant but tended toward a constant as the velocity decreased. Forcheimer's and Klinkenberg's modifications can be combined in a rigorous way to account for both inertia and slip during steady flow. This will be shown in a future paper. The transient change of pressure in porous media has been described by the diffusion equation.3 This form results from eliminating the velocity and density fields from a combination of the equations of motion in the form of Darcy's law, the continuity equation and an equation of state. Fatt4 suggested that the cause of deviations from the prediction of the diffusion equation for pressure transients lies not in the choice of Darcy's law as the equation of motion but on the existence of dead-end pores which might invalidate the averaged equation of continuity. On the other hand, Oroveanu and Pascal5 noted chat the time derivative of the momentum density must be included in the equations of motion since this measures the local rate of change of momentum density. Their differential equation for pressure is the telegrapher's equation (neglecting gravity). However, their form of this equation predicts that the speed of pressure propagation through the pore structure is the same as that through the bulk fluid. M. K. Hubbert6 attempted a derivation of Darcy's law by volume averaging the Navier-Stokes equations. Since these equations represent momentum balance at a point within an open set of points containing the fluid itself, Hubbert's volume averaging cannot lead to tenns involving transfer of momentum between the fluid and the walls of the pores. Once these viscous tractions are lost by choosing a control volume containing only fluid, they cannot

By F. V. Lenel, J. A. Dromsky

The influence of thermal and mechanical treatments upon the elevated-temperature stability, the microstructure, and the mechanical properties of aluminumaluminum oxide alloys is investigated. Compacts from atomized and flake aluminum powders were sintered at temperatures just below the melting point of aluminum in a vacuum of 10-4 Torr for several hours and were then hot-extruded. During this treatment the hydrated oxide present on the surface of the powder particles decomposes, the water vapor produced reacts with the aluminum forming additional oxide, and the hydrogen developed is removed by diffusion to the surface. Extrusions of compacts so treated are stable at temperatures up to the melting point of aluminum and do not form blisters and internal defects typical of extrusions from untreated powder. Electron micrographs of extrusions from unsintered compacts show long parallel oriented platelets typical of the IN previous investigations1,2 the properties and structure of aluminum alloys were described which had been produced by cold compacting aluminum powder and then hot pressing and extruding the compacts. Both the structure and the properties of these alloys differ significantly from those of commercially produced aluminum-aluminum oxide alloys. When commercial alloys are produced, they are given a sintering treatment in air at about 600°C between cold compacting and hot pressing.3 During this treatment the hydrated oxide, which forms the coating on the aluminum-powder particles from which the alloys are prepared, is decomposed.4 The chemically bound water which is released reacts with the aluminum and forms aluminum oxide and hydrogen. Most of the hydrogen is eliminated by hydrated oxide skins on the original powder particles, while the oxide particles in extrusions from sintered compacts are broken up. The strength of extrusions from treated powder is somewhat lower, but their ductility is considerably improved over that of extrusions from untreated powder. The slip-trace patterns on electron microgvaphs of extrusions which had been strained in tension before replication indicated that the grain size of the extruded alloys was approximately the same as that of the original powder particles. Coarse-grained alloys were produced by severe cold work and annealing of the extrusions. They have significantly lower room-temperature strength, but about the same ductility as the vacuum-sintered fine-grained alloys. The size and shape of oxides in the coarsegrained alloys is similar to those of the fine-grained alloys, but the particles are somewhat more uniformly distributed. diffusing to the interior or exterior surfaces of the compact, but it is difficult to eliminate all of it because the solubility of hydrogen in solid aluminum is very low even near its melting point. Extruded alloys which are not sintered before hot pressing and extrusion appear quite sound upon metallo-graphic examination, but develop severe surface blistering and internal fissuring when they are heated to elevated temperatures after extrusion. Fissures and blisters have been observed even in commercial alloys which had been sintered in air, although they are much less severe.' Because of the importance of this sintering treatment it was studied in this investigation in a modified form, using vacuum sintering rather than sintering in air, to insure more complete elimination of occluded hydrogen. The technique is described and the effect of the treatment upon the structure of the alloys is documented. It has been known for some time that extruded aluminum-aluminum oxide alloys are very finegrained, but an exact delineation of grains in electron micrographs has not been possible. In the conventional metallographic-etching techniques etchants attack the interface between the second-phase particles and the matrix in the alloys much

Jan 1, 1964

By L. Yarborough, L. R. Smith

This paper presents results of a laboratory study of retrograde condensate recovery by revaporization into dry injection gas. Flow tests were performed in 10.6-ft long sand packs at 100F and 1,500 psi. In three runs methane revaporized the liquid from a n-pentane-methane mixture in the presence of immobile water. TWO of these tests were water-wet, and the third was totally oil-wet. In the three runs n-pentane recovery was complete after 2.5 hydrocarbon PV of injection. There was no significant performance difference between the two wettability extremes. In a fourth experiment, a methane-hydrogen sulfide mixture revaporized a synthetic light, sour condensate. No water saturation was present. Equilibrium compositions and volumetric data were obtained for the four-component condensate. The heavy component, n-beptane, was removed after 6 PV production. Comparison of the effluent fluid compositions with known equilibrium data shows that the flowing fluid was equilibrium vapor and that the mixing zone between equilibrium vapor and dry injection gas was short. Data indicated that complete recovery of retrograde liquid occurred after it was contacted by a sufficient quantity of dry gas. INTRODUCTION When pressure declines below the fluid dew point in a gas condensate reservoir, a liquid phase forms. In this process, referred to as retrograde condensation, the quantity of liquid formed is frequently small enough that the liquid is not a flowing phase. To prevent loss of valuable retrograde liquids, the process of dry gas cycling has been employed for several years as a more or less standard practice. In this procedure the reservoir pressure is maintained above the fluid dew point so that the liquid components may be produced as vapor and then separated at the surface. Although full pressure maintenance by gas cycling seems ideal in terms of preventing liquids loss, several factors can reduce the atuactiveness of such an operation. From a study of a condensate reservoir in Alberta, Canada, Havlena et a1.1 con-cluded that cycling under conditions of declining pressure leads to economic advantages and to a high recovery of hydrocarbon liquids. This study considered effects of volumetric sweep efficiency, retrograde behavior of the original wet gas and revaporization characteristics of the retrograde liquid when contacted by dry gas. The first major work concerning revaporization of liquid in a gas condensate system is that of Standing et a1.2 Calculations based upon the PVT behavior of a recombined gas condensate fluid indicated that all retrograde liquid can be recovered if it is contacted by a sufficient quantity of dry gas. The paper considered the effect of variable permeability upon the recovery of retrograde liquid. Standing et al. concluded that recovery of heavier components in the retrograde liquid is greatest if reservoir pressure is allowed to decline below the dew point prior to dry gas injection. Since the work of Standing et al., several laboratory studies have been reported which show that recovery of hydrocarbon liquids by vaporization into dry injected gas can contribute to increased recovery above that obtained by ordinary production practices. Vaporization from retrograde condensate,3 conventional oil4-7 and volatile oil8 reservoirs has been considered. There is little work that deals with revaporization recovery from condensate reservoirs. This study demonstrates that vapor-liquid equilibrium exists when a dry gas is injected into a porous medium containing retrograde condensate; investigates the effect of wettability on revaporization of retrograde condensate; and provides an indication of the amount of dry gas necessary to

Jan 1, 1969

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951

By Ralph E. Hartline, Wilfred Tapper

The Strataflow process for locating water entry in producing, wells is now available. This method as now practiced utilizes the fact that fluids of different salinities have different electrical resistivities. By introducing into the well a fluid of a markedly different salinity than that of the fluid being produced, a pronounced resistivity change will occur at the point of entry. By running a Strataflow survey the points of major and minor water entry may be interpreted from changes in the resistivity of fluid in the hole. Strataflow results are obtained with the well operating under almost normal producing conditions, and are a logical primary step in any workover program, having as its purpose shutting off of the water. INTRODUCTION Water production is a serious problem in many producing oil wells. It certainly increases lifting costs and in some cases presents a disposal problem. It often aggravates corrosion problems and can even endanger oil production. With accurate information to guide an effective workover program, many marginal wells could be restored to Profitable Production. The shortcomings of previous meth- ods of water entry location were recognized. The Strataflow process is the result of several years of development and field testing directed toward overcoming these limitations. It represents the continued development of a process reported by Silverman and Brown. The earlier work established the basic soundness of fresh-to-salt water resistivity contrast in delineating zones of water entry, but its application was limited by the difficulty of maintaining static balance of the well during preparation for the test. A more serious deterrent to its use, however. was its unadaptability to existing well logging service equipment and field operating methods. STRATAFLOW PRINCIPLE The general principle of the new method involves, first, conditioning the well by displacing the fluid in the bore of the well adjacent to the zone to be tested by a conditioning fluid which is miscible with the formation fluid. This displacement is carried out without interruption of the well production. The conditioning fluid must have some measurable physical, chemical, nuclear, or electrical property which is distinctive from that of the formation fluid. As the well continues to produce. formation liquid entering the well bore dilutes the conditioning fluid so that zones of entry may be determined by making a log of the property undergoing change. This general principle may be applied to indicate zones of either water or oil entry by suitable selection of conditioning fluid and proper logging equipment. The Strataflow process, as it is currently practiced for water entry location, uses fresh water as the conditioning fluid and depends for its operation upon the marked difference of electrical resistivity between this fresh water and the salty water produced by the formations. If possible. any necessary modifications of the well equipment are made a week or so before the test. The well is then returned to normal production. On the day the test is to be carried out. the conditioning water is landed at the bottom of the well and the test is made without interrupting production except for a brief period required for the conditioning water to consolidate into a continuous column extending to a point well above the test section. With this general description of the process in mind, a more detailed step-by-step description of the process will be clearer. PRELIMINARY PREPARATION OF WELL The Strataflow survey, as it is currently practiced for water entry location, is applicable only to pumping wells. Since the required electrical measurements are made by a special

Jan 1, 1952

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By Donald Ofte, L. J. Wittenberg

The absolute viscosity coefficients and activation energies for viscous flow of bismuth, lead, and zinc are reported. The viscosities were measured in an oscillating cup viscosimeter from nearly 1000°C to within 1 deg of the melting point of zinc; 2 deg of the melting point of lead; and in the supercooled condition of bismuth, 9 deg below the melting point. Two methods of relating the change in the viscosity coeflicient with temperature were compared. From the plot of the logarithm of viscosity (77) as a function of reciprocal absolute temperature (1/T), the equations of the lines which fit the data are: AS a part of the Reactor Fuels and Materials Research program at Mound Laboratory, precise measurements of the physical properties of liquid metals are of interest because the desirability for a low vapor pressure liquid coolant in high-temperature nuclear power plants has focused attention on the properties of the liquid metals.&apos; Also, a clearer understanding of the liquid metal state can be achieved when better measurements are available. For these reasons, the viscosity values of certain liquid metals have been determined. The viscosities of the liquid metals, bismuth, lead, and zinc are measured in an oscillating cup viscosi-meter. In this apparatus the liquid is sealed in a right-circular cylindrical cup which is attached to a torsion fiber so that the system forms a torsion pendulum. The damping effect of the molten metal upon the normal oscillations of the torsion pendulum is a function of the viscosity of the liquid. This method is advantageous because of the small amount of sample required (8 to 10 cc), the ease of remote operation of the apparatus in a vacuum system, and the containment of the liquid metal in a hermetically sealed, nonreactive, tantalum crucible. With the liquid metal sealed in the crucible, loss of liquid by vaporization and chemical reactions with atmospheric gases are prevented. Additionally, an absolute viscosity determination is obtained which avoids the sources of possible error in a relative measurement. The difficulties in a relative method include the repetitious cup calibrations, and the uncertainty inherent in the practice of calibration of the apparatus at room temperature and extrapolation to the high temperatures necessary for the investigation of most liquid metals. The oscillating cup viscosimeter was first described by Meyer in 1891.2 The first complete mathematical treatment offering an absolute measurement of viscosity with this type of apparatus was proposed by Andrade and chiong3 in 1936 for an oscillating sphere filled with a liquid. This solution was modified to include a right circular cylinder by Hopkins and Toye4 in 1950, and R. Roscoe5 in 1958. Roscoe&apos;s treatment for the calculation of the viscosity of a liquid at a particular temperature from the logarithmic decrement and period of oscillation of the torsion pendulum was used in this investigation. A detailed description of the method of calculating the viscosity from these measurements has been reported earlier.&apos; This calculation has been programmed for the IBM 704 and IBM 1620 computers for expedition of the otherwise laborious calculations. APPARATUS The cutaway view of the apparatus in Fig. 1 shows the suspension system within the high vacuum enclosure. The low residual gas pressure. maintained between 1 x 10-4 and 5 X 10-6 mm Hg during a determination, avoided both air drag on the pendulum and

Jan 1, 1963

By A. F. Crawley

The densities of some liquid Pb-Sb alloys up to 11 wt pct Sb and Pb-Sb-& alloys up to 10 pct Sb/10 pct Sh have been determined by a pycnometric technique over a temperature range of about 130°C above their melting points. The data given are accurate within 0.05 pct. Density is shown to vary linearly with temperature , and equations relating these quantities have been formulated. Molar volumes calculated from the density data indicate that volumetric deviations from ideal mixing are undetectable within the limits of experimental error. A continuing research program into some fundamental physical properties of liquid metals is being pursued at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This work has received support from the Canadian Zinc and Lead Research Committee in cooperation with the International Lead and Zinc Research Organization. This paper, which reports some density data for Pb-Sb and Pb-Sb-Sn alloys, follows previous work from this laboratory on lead, tin, and Pb-Sn alloys.&apos; Of previous data from others, Greenaway2 and Sato and Munakata3 have reported results on Pb-Sb alloys. No previous work has been published on the ternary Pb-Sb-Sn alloys, reported here. EXPERIMENTAL METHOD Densities were measured by a pycnometric technique which has been described in detail and appraised for accuracy in earlier Mines Branch reports.475 Fig. 1 shows the densitometer with the pycnometer in position for a run. The pycnometer is also shown in some detail. The pycnometer of dense, high-purity graphite, about 14 cu cm in volume, was carefully machined to a uniform, smooth finish. The height was measured by a depth micrometer and the diameter by fitting precision gage blocks between steel balls.&apos; In each case several readings were taken, and the final results were considered accurate within 0.01 pct. The resulting volumetric uncertainty together with small inaccuracies in the coefficients of linear expansion of graphite lead to a maximum systematic uncertainty in the method of ±0.03 pct. As shown in Fig. 1, the pycnometer lid is a threaded cap. Thus, the charge, a cylinder of the alloy, can easily be inserted and the solidified metal can readily be removed after a run. The dimensions of the cylindrical charge are chosen to ensure that, once molten, the metal will not only fill the pycnometer completely but will discharge an excess into the excess-metal float chamber. AS the temperature is increased above the melting point, the volume of metal in the excess chamber increases until the system has equilibrated at the desired temperature. At this point, the excess chamber is moved to one side by twisting the shaft F, leaving a fixed volume of liquid metal in the pycnometer. This volume of fluid is readily calculated using measured coefficients of linear expansion of the graphite which expands anisotropically. The associated weight of fluid is determined as the weight of the solidified metal removed after the furnace has cooled down. Alloys were prepared from 99.997 pct Pb, 99.999 pct Sn, and 99.999 pct Sb, being melted by an electric furnace in a graphite crucible and poured into graphite molds. Several density specimens of the same nominal size were machined from each ingot, and, by comparing specimen weights, relative differences in specimen composition resulting from segregation in the ingots could be detected. In this way, segregation was found to have occurred in Pb-Sb alloys at compositions beyond the eutectic (11.2 pct Sb) and this

Jan 1, 1969

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7&apos;his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By R. T. Hukki

The purpose of this paper is to present an analysis of the unit operation of grinding and the circulating load, of the unit operation of classification and the circulating load, and of the two superimposed into one operation to clarify the overall trend of events relating the circulating load to the capacity of the closed circuit grinding system, to the specific surface area of the final fine product, and to the energy consumption in the closed circuit grinding process. The capacity of the closed circuit is frequently, if not always, determined by the classifier, not by the mill." With these words a startling idea was expressed in 1934 by Dorr and Anable.1 Today, some 30 years later, grinding in closed circuit is universally accepted. The basic curve presenting the capacity factor versus circulating load by Dorr and Anable has obviously been so convincing that not a single authoritative investigation regarding its validity seems to have been conducted. The only major subject of discussion appears to have been the relative merits of the &apos;high&apos; and &apos;low&apos; circulating loads. It seems to be universally agreed that much still remains to be hoped for regarding sharpness of classification. BASIC CURVES FOR CONSTANT MILL LOADING Fig. 1 presents a series of basic curves for constant mill loadings in function of new feed rate and circulating load. The mill loading indicated by each curve is the sum of hourly tonnages of new feed and circulating load. For example, at point 0 where the new feed rate is 100 t/h and the circulating load 300%, or 300 t/h, the mill loading is 400 t/h. In closed circuit grinding, the new feed rate corresponds to the rate of finished classified material produced. Although at this stage the effect of classification is excluded in construction of the basic curves, the trend indicated by these curves is strongly in favor of closed circuit operation under relatively small circulating loads. A study of the curves reveals that, e.g., a mill operating under a load of 200 t/h at point P where the new feed rate is 50 t/h and the circulating load 300% will also operate under the same total load at point Q where the new feed rate is 100 t/h and the circulating load 100%. In other words, a reduction of circulating load from 300% to 100% would lead to doubling of the new feed rate and doubling of the rate of production of finished material, without a change in the total mill loading. The obvious question is, is it also possible by a reduction of the circulating load in a closed industrial grinding circuit to increase the production of finished classified material and, if so, how and to what extent? GRINDING TESTS BY DORR AND ANABLE In a series of open circuit grinding tests reported by Dorr and Anable1 limestone was ground at various feed rates in a 3-ft ball mill. The original data are reproduced in Table I. It can be seen that with the increased feed rate production of -65-mesh material increased and the energy consumption per unit weight of the -65-mesh product decreased in the reverse ratio. The data shown in Table I have been reproduced for our purposes in Table II for a scale corresponding to grinding in a large industrial mill. This reproduction

Jan 1, 1968

By James M. Schopf

Gilbert H. Cady (Senior Geologist, Head of Coal Division Emeritus, Illinois State Geological Survey, Ur-bans)— Those coal mining and preparation engineers and operators who read this article will probably be most concerned with those parts which deal with the applied aspects of coal petrology in the fields of mining and technology. Actually the two categories overlap to such a degree that they are essentially one. The article appears to suggest that there are two points of veiw in the field of applied coal petrology. From one viewpoint the interest is in the attributes of the various macerals (Fig. 4)—vitrinite, exinite, and inertinite—-in terms of utilization (when the coal is burned, coked, gasified, hydrogenated, etc.). From the other point of view, assuming that the macerals do possess individuality in behavior, interest attaches to the possibility that coal of a particular type (maceral composition) can be prepared by discriminating methods of preparation and blending. Most of the 29 items listed for mining and technology can be assigned to one or the other of these two categories. Somewhat the same simplicity that resides in the items of the proximate chemical analysis is desirable for the petrologic analysis. This simplicity appears to be fairly well achieved by the group maceral device provided mineral matter is also included. At present, without fully adequate experimental substantiation, the three types of material represented by the group macerals vitrinite, exinite, and inertinite are regarded as sufficiently different in composition and properties so that the preponderance of any one type gives the coal distinctive properties provided it is not too high in rank. This appears to be increasingly true with coals of decreasing rank from medium volatile bituminous coals downward. The article reflects the great emphasis placed on the technique of descriptive coal petrology in America. Such description has resulted in a good understanding of the nature of the fundamental variability in the physical composition of bituminous coals. Such understanding has been attained very largely by the thin section technique used in coal bed profile analysis introduced by R. Thiessen after the manner suggested by the data assembled in Table 11. In contrast, the group maceral concept of coal analysis in terms of the categories indicated on the left hand side of Fig. 4 is particularly useful for broken coal analysis and applied coal petrology, in which evaluation is largely based on quantitative concepts. It is inadequately emphasized in this article that although the Thiessen procedure is suitable for the purpose of petrologic description in which texture and orientation are of critical importance, it is less well adapted to the technological uses of applied coal petrology. No doubt those persons whose interest may have been aroused in the possibilities of more refined coal preparation by this and other recent contributions to the literature of coal petrology will understand that certain technical aspects of coal petrology, particularly in the field of descriptive petrology, are still a matter of some controversy among the coal petrologists, but they will also appreciate that Schopf has made an important contribution to the field of coal petrology in America by pointing out that such petrology requires consideration of disoriented or broken coal samples and that results are expressed less in descriptive terms than in quantitative values with respect to the four types of material composing coal—-vitrinite, exinite, inertinite, and mineral matter. Unfortunately because so much American coal petrology has been descriptive of the coal in the bed there is a dearth of literature on applied coal petrology. Research and experimental data in this field are greatly needed.

Jan 1, 1959

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown&apos;s paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).&apos; Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By Charles Will Wright

ALTHOUGH the United States has long led all other countries in both the production and consumption of mineral products, the trend seems definitely toward an increasing dependence upon foreign sources of supply. This is not to take the position that we are either a have or a have-not nation. For years we shall continue to secure a large proportion of our needed minerals: from our own mines, but we must face the fact that this century has seen "a more thorough and intense development of the mineral resources of the United States and a greater depletion of its irreplaceable mineral reserves than has occurred in most other countries. An audit of our mineral production given in the attached charts discloses the extent of our deficiencies. Because of these facts, low-cost foreign sources offer a promising field for the investment of a portion of our mining capital and an opportunity to obtain for the United States a greater supply of strategic metals and minerals. How. ever, to reach this end, the industrialist investing in the foreign field must have the full co-operation and strong backing of the Federal Government and the involved Federal agencies.

Jan 1, 1947

By I. B. Cadoff, J. C. Bilello, R. Rosenberg

Diffiusion of magnesium into the surface of LiF crystals to controlled depths and subsequent heat treatments provided a wide range of surface zone harahesses and structure, The bend strength of the LiF crystals was increased by as much as an or-dev of magnitude. Ductility was achieved when dislocation generation occurred in the diffusion zone or when dislocations penetrated to the surface from the intevior. A critical surface hardness of 130 to 140 kg per sq mm was found helozu which generation could take place in the diffusion zone and ahoue which the zone was impenetrable, This hardness was obtainable by several methods, among them the aging of quenched MgF2 -LiF solutions to produce MgF, precipitation. Maximum hardness was ohtained in quenched specimens with no visihle evidence of MgF,. Diffusion-zone formation followed a parabolic rate law and an activation energy of 20.9 kcal per mole was obtained for the process. RECENTLY, the properties of ionic crystals as related to surface condition have been receiving much attention, specifically the transitions between ductile and brittle behavior. Originally Joffe 1 showed that NaCl crystals could be made ductile by immersion in water and related this to the elimination of surface microcracks. Aerts and DeKeyser 2 and Gorur 3&apos; have subsequently shown that ionic crystals are inherently ductile and are embrittled through contact with air. Machlin and Murray4 hypothesized that a layer of NaCIO3 produced by contact of ozone with NaCl induced embrittlement by acting as a barrier to outward dislocation flow. westwood,&apos; Rosenberg and Cadoff,9 and Bilello and cadoff&apos; have reported surface strengthening of LiF crystals by coating with a magnesium compound and then heat treating for adherence. The major effect of the coat was to inhibit dislocation-slip lines from reaching the specimen surface. westwoods showed microcrack formation and fracture to be caused by slip-band interactions at the surface. The material presented in this paper is an extension of the work reported earlier by Bilello, Rosenberg, and cadoff&apos;6,7 and illustrates the wide range of surface properties and bulk behavior obtainable by use of heat-treated magnesium-diffused surface regions in LiF crystals. EXPERIMENTAL PROCEDURE The LiF single crystals were obtained from the Harshaw Chemical Co. Some batch to batch variation was observed; therefore all specimens for a given test series were cleaved from the same crystal. The typical dimension used was 1 by 0.1 by 0.40 in. Surface damage resulting from cleavage was removed by chemically polishing in a 2 pct NH4OH solution. Each group of specimens was given a vacuum anneal at 700°C for 4 hr to provide a base standard for measuring comparative effects of various surface treatments. To produce the reacted surface zone, the annealed specimens were immersed in a boiling suspension of MgF, in doubly distilled HzO, agitated slbwly for 30 sec, removed, and dried at room temperature. Uniform coatings of MgF, were deposited with a thickness of approximately 5 mils. It should be noted that this technique can be modified for use with crystals which are soluble in water by using boiling absolute alcohol as the dissolving medium. This was found effective for the coating of NaCl with MgF2. The diffused surface zone was obtained by annealing the coated samples at elevated temperatures in a vacuum of lob4 mm Hg. Penetration depth was controlled by varying the annealing time from 1/2 to 28 hr. After heat treatment, the samples were tested for bend strength and hardness. Load was applied by four-point bending in a hard-beam testing jig. Four-point rather than three-point bending was used to provide a wide area of constant stress and to minimize the effect of localized inhomogenities in the specimen. The deflection rate was 8 x min-&apos; and the distance between knife edges was 1/4 in. Load-time curves were obtained from a chart recorder coupled to the machine and converted to resolved shear stress on the shear plane vs deflection, as plotted in the figures. The unstressed portions of the sample outside of the two outer knife edges were used for the microhardness studies. Microhardness measurements were made with a Bergsman tester attached to a Reichert metallograph. All hardness impres-

Jan 1, 1964

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal&apos; and by Chew and Connally&apos; for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7&apos; API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.&apos; All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By Ravindra M. Nadkarni, Milton E. Wadsworth

The kinetics of cetnentation of copper with iron were observed to follow first-order kinetics and increase with speed of agitation to a limiting value. Maximum rates agree closely with theoretical values based upon a model of aqueous solution diffusion through a litniting boundary film. Back reaction kinetics are shown both theoretically and experimentally to be independent of ferrous iron concentration in solution. The inlportance of attnospheres of air, oxygen, nitrogen, and hydrogen was studied and the results have been correlated with several impovtant oxidation processes involving metallic iron and copper. The kinetics of the reaction of ferric ion with metallic iron were found to be slow in the absence of metallic copper and essentially proportional to the surface area of metallic copper present in the system. THE precipitation of copper on iron is classic as an example of a relatively ancient art applied successfully for centuries with little fundamental understanding of the important parameters involved. There is some indication that the process has been a commercial means to produce copper since the sixteenth century.&apos; The amount of fundamental work on the cementation of copper with iron is not great. Wartman and Roberson2 carried out a series of detailed copper cementation experiments using natural and synthetic mine water. The following were presented as the three principal reactions: Reaction [I] is the desired cementation reaction and accordingly 0.88 lb of iron would produce 1 lb of copper. In actual practice iron consumption would more normally fall in the range of 1.5 to 2.5 lb per lb of copper. Wartman and Roberson attributed the excess consumption of iron to Reactions [2] and [3]. They found that Reactions [I] and [2] proceeded at approximately the same velocity while Reaction [3] was much slower and would be diminished by controlling the contact time. It was also pointed out that increased agitation is beneficial in removing hydrogen bubbles and barren layers of solution at the iron surface as well as removing contaminants resulting from the hydrolysis of iron. Episkoposyan3 and Episkoposyan and Kakovskii4 studied copper and silver cementation on rotating iron disks in chloride solutions. The kinetics based upon a diffusion model were first order and varied linearly with surface area and with angular velocity raised to the one-half power according to the Levich equation. The experimental activation energy for both copper and silver was approximately 3 kcal per per mole. Excess iron consumption was found to increase with temperature. The rate of cementation first increased with increasing acidity and then diminished at high acid concentrations. sutolov5 has presented an excellent review of the Leach-Precipitation-Flotation (LPF) process including a discussion of copper cementation from an electrochemical point of view although few experimental results were presented. From voltage considerations he predicted that cementation should not be influenced by the concentration of ferrous iron in solution. He considered several secondary reactions including Reactions [2] and [3] and pointed out the importance of oxidation of ferrous iron to ferric with oxygen. In addition it was suggested that Reaction [2] was enhanced by the dissolution of metallic copper by ferric iron which in turn consumed excess iron by the cementation reaction, Eq.[1]. Cementation of copper on metals other than iron has been studied by several investigators but, as in the case of iron, the amount of fundamental work is not extensive. Bashkova and kovalenko6 and Bashkova7 studied the cementation of copper on indium from copper and indium sulfate solutions. The rate was found to be first order and to increase with acidity. This was associated with a decrease in potential (EIn — ECu) and the simultaneous reduction of hydrogen ions at low pH. The rate of cementation also decreased with increasing indium concentrations which was postulated to be due to the decrease in the rate of diffusion of the ions in solution. Below 97°C the experimental activation energy was found to have the unusually low value of 2 kcal per mole and was attributed to diffusional control. Above 97°C the rate increased suddenly and was explained as a change in the rate-controlling step to a chemical reaction. In Part I of this study Nadkarni et a1 .1 have reported on preliminary results obtained in a laboratory study of the kinetics of the cementation process. The rate was found to be first order, proportional to the surface area of the iron, and to increase with speed of stirring until a maximum rate was observed. At low stirring speeds the deposit was spongy and adherent. At medium speeds the copper peeled off in bright strips and at high speeds finely divided copper was produced and continually removed from the surface. The amount of excess iron consumed increased with speed of stirring and with temperature. The average experimental activation energy combining results from several types of iron was 5.8 + 1.6 kcal per mole suggesting diffusional control through a limiting boundary film. Traditionally copper cementation has been carried out over the centuries in gravity-fed launders of various design containing scrap iron. More recently rotating drum precipitators and activated launders8&apos;10 have been used. In the latter, copper-bearing solutions are

Jan 1, 1968

By AIME AIME

APOCRYPHAL, no doubt, but widely entertained is the proposition that top-flight mining geologists never agree with each other on anything. Being rugged individualists, they frequently seem intolerant of opinions that conflict with their own. However, one may suspect that controversy is often more apparent than real. For example, at last summer&apos;s meeting of the American Mining Congress, Ira B. Joralemon and Reno H. Sales, discussing "Mining Geology, Today and Tomorrow," seemed to be in serious disagreement over various phases of the subject; but much of this arises from the different angles of approach of the two distinguished and successful ore finders.

Jan 1, 1941