Search Documents

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By T. D. Yensen

Discussion of the paper of T. D. YENSEN, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 483 to 512. JOHN A. MATHEWS, Syracuse, N. Y.-Concerning the critical composition of the steel containing 2.50 per cent. of silicon, I may say that 12 or 13 years ago we made some of these alloys. They. were not as pure as the alloys made by Mr. Yensen, nor were they melted in vacuo, but one of them contained exactly 2.50 per cent. silicon, and about 0.25 per cent. carbon. It gave us no trouble whatever in hammering to a billet or rolling into bars, nor even when rolling into ¼ -in. wire rods. The steel in question was practically free from everything except carbon or silicon and contained no manganese sulphur or phosphorus worth mention. The alloy containing 2.50 per cent. of silicon worked perfectly well, as well as one containing 0.5 per cent. silicon, and it seems to me that further work should be done by Mr. Yensen on the physical properties of alloys at this seemingly critical change point. W. E. -RUDER, Schenectady, N. Y.-We -have made silicon steels of practically every composition and have never obtained any material under 5 or 6 per cent. of silicon which was brittle. This may be due, of course, to the presence of carbon, in some of the 'commercial materials, and I presume that Mr. Yensen would argue that the: presence of this carbon might prevent inter-granular brittleness. However, all of our silicon steels, up to 5 per cent. of silicon, by treatment in hydrogen at temperatures near the melting point, can be made to show inter-granular brittleness. Furthermore, the material made brittle in this way could be restored by treating at the same temperature in hydrogen containing a hydrocarbon vapor. I discussed this matter some years ago in a paper on inter-granular cement. It therefore appears likely to me that Mr.

Jan 5, 1916

By Walter W. Bradley

Barite, or barytes as it is sometimes called, belongs to one of the lesser groups of nonmetallic minerals, of which 15 to 20 varieties are mined in California in amounts varying in value from a few hundred to almost half a million dollars annually. Commercial production of barite in California, according to the records of the State Mining Bureau (now Division of Mines), began in the year 1910 with shipments totaling 860 tons, valued at $5640 f.0.b. rail shipping point. With the exception of the years 1924 and 1925, when no shipments were made, the output has varied, reaching a maximum of 17,993 tons, worth $90,617, in 1927. The 1928 output was 13,406 tons, worth $55,888 f.0.b. rail shipping point, bringing the state total to the end of 1928 to 59,972 tons, valued at $313,930. Consumption of BaRitE in United States Crude barite sold or used by producers in the United States for the year 1927 amounted to 248,219 tons, valued at $1,594,423, according to the U. S. Bureau of Mines.l In addition, there was imported, principally from Germany, a total of 70,274 tons, valued at $253,284. Manufactured products from these tonnages combined were distributed in 1927 (the latest year for which figures are at present available) as follows: ground barite, 57,658 tons; lithopone, 174,083 tons; barium chemicals (including carbonate, 4,960 tons; chloride, 3,541 tons; binoxide and sulfate or blanc Jixe combined, 13,354 tons). Missouri accounts for nearly 50 per cent of the domestic crude barite, followed by Georgia and Tennessee, with lesser amounts from Arizona, California, Nevada, South Carolina, and Virginia. Occurrence and Uses of Babite2 Barite, also called "heavy spar" and "tiff," is theoretically composed of 65.7 per cent of barium oxide (BaO) and 34.3 per cent of sulfur

Jan 1, 1931

By Maurice Ewing, L. Don Leet

The most important quantitative method in seismic prospecting by refraction shooting is the method of profiles. A profile is established by firing a series of charges at various points along a straight line which terminates at the seismograph. The same data are obtained by repeatedly firing charges at one place and recording at a series of stations along the line of the profile. The quantities which are measured are the distance x from each firing position to the seismograph and the time t required for the first disturbance from each explosion to travel to the seismograph. These data are used in plotting the familiar time-distance graph. The only time-distance graphs that will be considered here are those obtained in localities where the velocity of propagation depends solely on the depth beneath the surface; that is, where there is no slope in the subsurface. The essential calculation to be made from such a time-distance graph is the determination of P(x), the maximum depth of penetration of a disturbance coming to the seismograph from a firing point at the distance x from the instrument. If the time-distance graph consists of a series of straight lines, as is often the case, the penetration P(x) can be calculated by means of formulas which appear in almost every description of seismic prospecting.' Until the present, however, the only formula that has been available for calculating P(x) for time-distance graphs which are smooth curves is one which requires an arbitrary assumption regarding the law of velocity increase with depth.2 The practice in these cases has been to approximate the curve by means of a number of straight lines and then to apply the ordinary straight-line formulas. This method clearly can yield accurate results only when a sufficiently large number of straight lines is used. The labor of computation increases rapidly when the number of lines is increased, so too few lines often are used. Further than that, there is a strong tendency to overlook the approximate nature

Jan 1, 1932

By W. P. Shinn

In a paper contributed by W. A. Goodyear, M.E., on "Water Gas as Fuel," read at the Boston Meeting, February, 1883,* the following statenlent was made: "The latest experiments on a scale of some magnitude in our citier, in the way of heating buildings and furnishing power for manufacturing purposes, have been by the distribution of high-presslire steam through pipes laid in the streets. Hilt these experiments (1) have not hitherto been very successful; and when we consider the high cost and (2) the great and unavoidable loss of heat and power, which always accompany the conveyance of high-pressnre steam to any considerable distance in pipes, to say nothing of (3) certain practical difficulties in the management of the pipes themselves, (4) it is evident that all such methods must eventually disappear before a system which can furnish a cheap gas of great heating power, easily distributed wherever wanted, without requiring pipes to stand pressures of 50 to 75 pounds per square inch, and (5) without keeping the whole mass of ground in the streets through which it passes hot, gratis, for a distance of ten or fifteen feet, in all directions around the pipes!' For the purpose of controverting Mr. Goodyear's statements in regard to steam-distribution in cities, I hare numbered the points made in his indictment, my principal object being, not a professional discussion of the technical and theoretical merits of steam vs. watergas, but a simple statement of facts, in regard to the present state of the street system of steam distribntion. Taking Mr. Goodyear's points in their order: 1. Concerning what he terms " These experiments," saying that they " have not hitherto been very successful," I propose to show, that the problem of stearn-distribution has passed beyond the experimental stage, and that its practical solution is highly successful. This will be shown by the facts hereinafter fully set forth. 2. "The great and unavoidable loss of heat and power whicn always accompany the conveyance of high-pressure steam to any con-

Jan 1, 1884

By R. S. Wagner, W. G. Pfann

If an electric field is applied to a conducting liquid solution, changes in concentration usually occur because of differences in ionic mobilities. A variety of ways of utilizing this effect in conjunction with the freezing process are discussed in principle. For example, if a column of binary eutectic liquid is maintained a few degrees above the melting point and a field is applied, the component solid solutions will crystallize at opposite ends of the column until the liquid is consumed. An expression for the effective distribution coefficient, k, is derived for the case of a direct current Passing through a solid-liquid interface. It is shown that k can be varied It is well known that solute distributions in crystalline substances can be controlled by careful freezing from melt or solution. It is also well known that an electric field can produce substantial changes of concentration in liquid solutions by virtue of differences over a wide range, including values outside the usual range between ko (the equilibrium value) and unity. Hence, for many systems: the efficiency of zone refining can be increased; a ko of unity can be made greater or less than unity; solutes that lower or raise the fretzing point can be concentrated at the same end of the ingot by zone refining; be made equal to unity; and the tendency toward constitutional supercooling can be reduced. The methods of field-freezing are applicable to a wide range of materials including metals, semiconductors, and ionic conductors. in ionic mobility. In this paper we discuss, in principle, some methods that combine these techniques in useful way's. The methods are designated by the general term, field-freezing. Topics discussed include separation of the components of a eutectic, crystal growth, and controlling the value of the effective distribution coefficient. The methods are applicable to a broad range of materials, including alloys, semiconductors, fused salts, and other liquid electrolytes.

Jan 1, 1962

By H. C. Howarth

This paper gives observations on ground movement and subsidence resulting from pillar drawing in the Lick Run section of Montour No. 10 mine of the Pittsburgh Coal Co. adjacent to solid coal owned by the U. S. Bureau of Mines at its Experimental mine in Snowden Township, Allegheny County, Pennsylvania. The investigation was planned by George S. Rice, chief mining engineer of the Bureau, who arranged the necessary cooperation with Dr. L. E. Young, vice president of the Pittsburgh Coal Co. Engineers of that company placed permanent monuments on the surface to establish the boundaries of the coal owned by the Bureau and to furnish fixed points to which all levels were referred. Engineers of the Experimental mine staff then covered the ground under observation with a checkerwork of monuments made of oak pegs set into the ground at 50-ft. intervals in two directions at right angles to each other. The level of these pegs was determined first from Dec. 16 to 30, 1929; again from May 25 to June 5, 1930, and finally from July 7 to 15, 1931. Observations were then discontinued because work had been stopped temporarily in this part on Montour 10 mine. General Conditions Fig. 1 is a plan of the part of the area under observation with which this paper deals. The mine is developed on a room and pillar system known locally as half advancing and half retreating. As Nos. 35 and 36 butt entries were advanced, rooms were driven from No. 36 and drawing of the room pillars followed their completion. When the entries reached the boundary, rooms were started from No. 35 butt beginning at that point, and all remaining pillars were drawn as rapidly as possible. The rib lines of Jan. 9 and June 13, 1930, were surveyed a week to 10 days after the first and second sets of levels were run, and there was some advance in that period. The rib line of July 15, 1931, agrees in time

Jan 1, 1934

By AIME AIME

BEFORE proceeding with the papers scheduled for the ore and foundry session*, the teller's report on the election of officers for the ensuing year was presented, a; follows: Chairman. G.C. F. MacKenzie; vice-chairmen, C.S. Robinson, J. T. MacKenzzie, C. E. Meissner; executive committee, A. L. Field, R. F. Harrington, E. F. Kenney lit. Waterhouse announced that the fall meeting will be devoted to alloy steel. This meeting will be held in Chicago the week of Sept. 22 in connection with the National Metal Congress. He also announced that oxygen in steel will be the central idea of the meeting which will be held in New York next February. The first paper, entitled "Sintering Limonitic Iron Ore at Ironton, Minn.," was presented by Perry G. Harrison (T. P. 284), the author. Sintering was first un¬dertaken in 1024 to treat Cuyuna range iron and manganiferous ores low in silica and high in moisture and containing objectionable qualities of fine... A Dwight-Lloyd machine was first installed. This machine was replaced by a larger one having a width of 72 in. The power cost was decreased from about $11.22 per ton of sinter on a 42-in. machine to about X0.14 for the 72-in. machine. The tons of sinter per man-shift was increased from 11.86 to 16.77. Improvements embodied in the larger plant reduced the cost of sintering to $0.41. The analyses of iron ore and manganiferous ore and the sinter produced from these materials was used to show the increase in value at the mine resulting from sintering. Crude iron ore actually unsalable was increased in value f.o.b. mine from a theoretical figure

Jan 1, 1930

By R. L. Skaggs, D. T. Peterson

The effect of carbon in solid solution on the plastic behavior of thorium was studied by measuring the flow stress of Th-C alloys from 4.2" to 573°K and at several strain rates. Carbon was found to strengthen thorium primarily by increasing the thermally activated component of the flow stress. The strengthening due to carbon was directly proportional to the carbon content and decreased rapidly with increasing temperature up to 423" K. The flow stress also increased with increasing strain rate. The strengthening appears to be due to a strong short-range interaction between carbon atoms and dislocations. A yield point was observed in the Th-C alloys which increased with increasing carbon content. JTREVIOUS study of the mechanical properties of thorium has been confined largely to the measurement of the engineering properties. Work prior to 1956 has been summarized by Milko et al.1 who reported that additions of carbon to thorium sharply increased the room-temperature strength. In addition, the yield strength was observed to decrease rapidly over the temperature range from 25" to 500°C. In 1960, Klieven-eit2 measured the flow stress of thorium containing 400 ppm C. He found that over the temperature range from 78" to 470°K the flow stress was strongly dependent on temperature and rate of deformation. A drop in the load-elongation curve, or a yield point, was observed over most of the above temperature range. Above 470°K, the flow stress was nearly independent of temperature and strain rate. This strong temperature and strain rate dependence of flow stress is not generally observed in fcc metals. It is, in fact, more typical of the behavior reported for bcc metals. Bechtold,3 Wessel,4 and conrad5 have pointed out the striking difference between the commonly studied bcc metals and fcc metals in regard to the effect of temperature and strain rate on the flow stress. Zerwekh and scott6 studied the plastic deformation of thorium reported to contain 12 ppm C. They found that this material did not obey the Cottrell-Stokes law as expected for fcc metals. In addition, they found values of the activation volume smaller by an order of magnitude than expected for an fcc metal. They concluded that thorium was strengthened by a randomly dispersed solute. Thorium differs from many other fcc metals that have been studied extensively in that it shows a relatively high carbon solubility at room temperature. Mickleson and peterson7 report the solubility limit at room temperature to be 3500 ppm C. The lowest value reported is that of Smith and Honeycombe8 who report the limit to be 2000 ppm C at 350°C. The pres- ent investigation was a systematic study of the flow stress and yield point phenomenon of thorium over a broad range of carbon content, temperature, and strain rate. EXPERIMENTAL PROCEDURE The thorium used in this investigation was produced by the reduction of thorium tetrachloride with magnesium as described by Peterson et a1.' Chemical analysis of the original ingot after arc melting and electron beam melting is shown in Table I. Alloys were prepared by arc melting this thorium with high-purity spectrographic graphite. Threaded specimens with a gage length 0.252 in. diam by 1.6 in. long were used for the constant stress or creep measurements. These specimens were machined from rod which had been cold-rolled and swaged to % in. diam. Tensile specimens were prepared by swaging annealed 3/8 -in.-diam rod to 0.102 *0.001 in. The as-swaged wire was cut to lengths of 2 in., annealed, and the center 1-in. gage length elec-tropolished to 0.100 ±0.001 in. The specimens were gripped for a length of 3 in. at each end by a serrated four-jaw collet which was tightened by a tapered compression nut. No slipping occurred in the grips and negligible deformation was observed outside the 1-in. gage length. Both the creep and tensile specimens were annealed at 730°C under a vacuum of 1 x X Torr. The resulting structures consisted of equiaxed recrystallized grains with a grain size of 3200 grains per sq mm for the tensile specimens and 2200 grains per sq mm for the creep specimens. After the specimens were prepared, samples were analyzed for nitrogen, oxygen, and hydrogen. The results of these analyses are given in Table 11.

Jan 1, 1969

By N. H. Emmons

THE work of a consulting engineer or manager, when controlling mining-operations, requires that he have all the information concerning the mine in as concise a form as possible, and as the ore-reserves and their depletion and enlargement are the vital points to be studied, it is well to have them kept up to date and in some convenient form. The present paper describes a method adopted by me, which shows in a very clear manner the ore-reserves in a mine. The case illustrated is that of a vein near enough to the vertical for the vertical elevation of the mine to be the main working-map. A flat ore-body would be represented on a similar plat, but instead of the horizontal thickness of the vein being shown in the circles, the vertical thickness would be inserted. Fig. 1 represents an ideal longitudinal elevation of a mine, plotted in the ordinary way, using 100-ft. blocks and section-lines. In a mine where the block-numbers are posted by the engineer underground, the system of keeping the ore-tonnages extracted from the different blocks is easily maintained, and the actual tonnages of ore extracted can be kept so that the surveyor can have a check on his estimate from time to time. The ore-reserve sheet, Fig. 2, should be the same size as the map it is to accompany. Each square is used for the description of the ore-reserve in the block it corresponds to on the elevation. Where the section-lines cross the levels a circle is drawn, in which are written the widths of ore at that point, these widths being used in the calculations of each block cornering in the circle. It has been found convenient to show the figures in black in the lower half of the circle when the actual widths of ore are known, and when it is necessary to make up the figures of probable ore, as at the time of making

Jun 1, 1912

T. M. Drown, South Bethlehem, Pa.: Mr. Thackray's paper shows in a striking way the high degree of rapidity and ac curacy exhibited by the chemists of our steel-works in ordinary everyday practice. That determinations made in an hour should present only slight differences in the third place of deci male is certainly matter for surprise and congratulation. This remarkable result has been due, perhaps, in part, to a remark able cause. The managers of works, ignorant of all the diffi culties of the laboratory, have demanded "the impossible " of their chemists—and the chemists have done it! Andrew A. Blair, Philadelphia, Pa.: Mr. Thackray's paper is extremely interesting, especially in its bearing on the question of a standard method for the rapid determination of phosphorus in the laboratories of steel-works. Before discussing the re sults in general, I desire to explain the results obtained by me under method A'. This is the method which I have used in the work of the sub-committee on Methods of the Interna tional Steel Standards Committee. It may be described briefly as follows: Solution in nitric acid; oxidation of carbonaceous matter by permanganate; precipitation of phosphoric acid by molybdate solution; reduction of molybdic acid in the reductor, and titra tion by permanganate. This method was used apparently by only three chemists, Dr. Dudley, Mr. Crowell, and myself. In determining phosphorus by this method, among the most essential points to be considered are the ratio of iron to molyb dic acid, or the reducing action of zinc on molybdic acid as compared to its reducing action on iron, and the ratio of molyb dic acid to phosphorus in the ammonium phospho-molybdate obtained by precipitation from the solution of the steel. In regard to the first point, the usually accepted ratio is 1 to 0.90756, or, as it is roughly stated, 0.9076, which is based on the assumed reduction of the molybdic acid to Mo12019,. This

Jan 1, 1896

By AIME AIME

YOU can place an exclamation point after the "and How" if you want to, but the way it stands it sum¬marizes the Mining Geology sessions quite nicely; "Why" in the morning, "How" in the afternoon. It is altogether fitting that Prof. McLaughlin and Reno Sales, who have themselves achieved enviable reputations in company work, should have led the program by presenting informally a chapter from the volume dedicated to the beloved dean of all economic geologists, Waldemar Lindgren. In opening the morning session, over which Sydney Ball presided, Donald McLaughlin emphasized the continuous role mining geology should play in operating technique. He pointed out the importance of structural relations in a broad sense, and the preponderant role they play in developing the manner of ore occurrences. He illustrated this by an account of the work at Homestake, using slides to show the stratigraphic sequence, the folding, and the orebodies of that camp. An interesting piece of detail was the distinction they found could be made be¬tween the chlorite near the ore masses, and that in the country rocks. Whether the cummingtonite, characteristic of the rock in which the ore is found, is of regional or of contact metamorphic origin caused some discussion. Dr. Lindgren inclined to the belief that it was contact, but L. C. Graton replied that they had found the weight of evidence was for a hydrothermal origin. D. F. Hewett raised the question as to whether, in the advancing development of the mining industry, there was still a place for the U. S. Survey geologist, and the consensus seemed to be that there should be. His role is changing from that of mapping mining districts in detail, now the task of the companies, towards a more general serving of the industry through the wider perspective his work gives him in contradistinction to the greater detail of knowledge accumulated by the resident geologist.

Jan 1, 1933

By S. F. Reiter

The paper presents isothermal recrystallization curves for 0.08 and 0.15 pct C steel at subcritical temperatures following small amounts of plastic deformation. The effects of deformation, temperature, and aging on nucleation and growth rates ore described. The free energy of activation for grain boundary migration in steel is given. SEVERAL excellent reviews of the literature have appeared concerning the recrystallization of metals.'-' The present investigation follows the approach advanced by Mehl, Stanley, and Anderson,6-7 in which the rate of recrystallization was analyzed in terms of N, the rate of nucleation, and G, the rate of growth of recrystallization nuclei. Two lots of low carbon, capped steel of the analysis given in Table I were studied. Each lot consisted of a 150 lb coil which had been hot rolled to 0.083 in. and then cold rolled to 0.042 in. at the mill. Strips 0.930 in. wide were sheared perpendicular to the rolling direction. Both steels were normalized before studying their recrystallization characteristics. The strips were cleaned, painted with a magnesia-acetone paste, and made into packs of equal weight, wrapped in 0.002 in. copper foil. The packs were placed in a salt bath at 900°C for 30 min and air cooled. A relief anneal followed in a second salt bath for 15 min at 650°C. The relief anneal was found necessary from early tests in which a longer incubation period and slower rate of recrystallization were observed in relief-annealed lot A steel than in similar material which was strained and recrystallized directly after being normalized. This effect, which indicates the presence of transformation and/or cooling stresses in steel air cooled from above the A, temperature, has also been observed by Samuels8 and Masing.9 Figs. 1 and 2 show the microstructure of lot A and B materials and illustrate the rather uniform No. 8 ASTM grain size produced by this heat treatment. Winlock and Leiter10 observed that strip specimens which had their sharp edges removed elongated more uniformly than those which were not polished. Similarly, when the sheared edges were removed on a belt grinder, it was found in the present investigation that such samples recrystallized more uniformly than did unpolished strips. Therefore, all strips were carefully rounded prior to their extension. The approximate strain limits for the production of large recrystallized grains are from 6 to 12 pct extension." It was found that for the purpose of this investigation, 8 and 9 pct elongation were suitable deformations. The strain rate employed was 0.01 in. per in. per min and produced a yield point elongation of 4 pct. Winlock and Leiter found that mild steel of No. 8 ASTM grain size gave the same yield point elongation when extended at 0.012 in. per in. per min. All of the lot A and B strips extended in tension developed a straight, stretcher strain line at each grip when the upper yield point was reached. The lines were parallel and made an angle of 55" with the edge of the strip. They approached each other with increasing strain and met near the center of the sample at the end of the yield point elongation. Immediately thereafter, a small drop in load was observed and then the load increased in a regular manner with increasing extension. The grips were initially 8 in. apart. After extension, the 6 in. gage length was carefully cut into 1 in. samples. The remainder of the strip was discarded. After a flash pickle in hot 50-50 hydrochloric acid, six samples, each of which had been taken from a different strip, were placed in a basket and submerged in a lead pot for isothermal recrystallization. Although no recovery effect was observed, strain aging did occur after extension. Therefore, samples were always recrystallized within 24 hr after their cold deformation. After recrystallization, the samples were etched with a solution comprised of one part by volume of nitric acid with three parts of water. Bromide printing paper was exposed directly at low magnifications and later used with a mask to measure the desired quantities. First, the average diameter of the largest grain visible in each sample was determined using dividers. Next, the number of recrystallized grains per unit area was counted and recorded as n. Then, for each sample, the combined area of the recrystallized grains was measured by transcribing the grain outlines to standard graph paper. Many determinations of the area of the recrystallized grains were repeated five times and indicated a standard error that was not greater than 25 pct. The average area for six samples was divided by the area of the mask to yield the percentage recrystallized. Recrystallization of 0.08 Pct C Steel The progress of recrystallization at 670°C after 8 pct elongation of lot A steel is shown in Fig. 3, a through f. The shapes of the growing crystals are approximately equiaxed, as is assumed in the

Jan 1, 1953

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By George Dyott

THERE are many who may consider a paper on aerial transport and its possibilities in connection with mining operations somewhat premature. Nevertheless, as there is considerable interest manifested in the subject at the present time and the amount of information available is both scanty and misleading, the result of investigations in some of the remote mining districts of Peru will not only be of interest, but will help crystallize, in the minds of many, a more correct conception of just what an airplane is capable of doing. By way of introduction, I will deal briefly with the types and varieties of airplanes now in use, and the developments of the past few years, pointing out -how the war has encouraged machines. of startling performance rather than those of commercial utility. I will then take up aerial transport in general, showing how airplanes may be employed to advantage and the particular kind of work for which they are best suited. This will cover a preliminary discussion on cost, which is one of the most important phases of the subject. In passing on from a general survey of the situation, I will deal with actual observations and investigations made in Peru. This part of the paper will be divided into two sections: the first, covering the mountainous districts of the Andes (Tamboras, Pataz, Soledad, etc.); the second, the alluvial deposits in the rivers, Chinchipe, Santiago, and Napo. In each case the question of atmospheric conditions, altitude, landing grounds, motors, cost, etc. will be discussed. While it is my intention to deal chiefly with mining in the sections mentioned, the same line of argument will be applicable to any other districts in the world. In conclusion, I will touch on the possibilities of using lighter-than-air craft of the Zeppelin type, followed by a summary of the most salient points brought out in the paper.

Jan 2, 1919

By R. W. Heins, N. Street

Recently Hiller1 reported results on the impairment of the strength of quartz glass rods through wetting, indicating that there was general agreement with the prediction of the Griffith formula in that for the liquids used the rods were weakest in water i.e. the liquid which probably had the greatest free energy of immersion. The Griffith equation predicts that the tensile stress necessary to propagate a crack of length c is where ? is the interfacial free energy, E Young&apos;s modulus. Since for a solid immersed in a liquid of surface tension ?L and contact angle 8 at the solid-liquid-gas contact, ?s - ?SL = ?L cos ? where ?s is the surface free energy of the solid. Hence comparison between ?L cos 0 and strength impairment should be possible. In a study of the usefulness of the Kuznetsov pendulum2 as a means of studying rock drillability we have determined the effects of various liquids on the pendulum hardness of Bavarian limestone. The pendulum used had diamond points (Burgess Vibro-graver), a period of 1.14 sec and a total on sample weight of 1191 g. The decline of the pendulum oscillations was recorded by a light beam on light sensitive paper carried on a kymograph. Rehbinder&apos;s expression relating hardness to amplitude attenuation as a function of time can be written In A = - (1/H) t + In Ao where A, A, = amplitude at time t and initial amplitude respectively, H = hardness parameter, and t = time. The line of best fit to the experimental points was determined using the IBM 7090 electronic computer, the computer also gave A, by extrapolation to zero time. The results for the various liquids tested are given in Table I and Fig. 1. The limestone surfaces were highly polished before testing and each reported hardness value represents the average of at least ten separate determinations of the pendulum decline curve. On each newly prepared surface the water value was again determined (also

Jan 1, 1964

By W. R. Hibbard

IN ref. 1, on the basis of tension and torsion experiments with single crystals of a brass, the values given in Table I were obtained for elastic coefficients. It was pointed out by Zener that the values for the 71.2 pct Cu were not satisfactory, since they resulted in a negative value for the bulk modulus, namely —4.17X1012 sq cm per dyne. In reevaluating the data of this investigation, it was determined that the reason for this negative bulk modulus lay in the extrapolation of the reciprocal Young&apos;s modulus to the zero value of the orientation function shown in Fig. 5 of ref. 1. This extrapolation was reevaluated by the method of least squares (50 pct probability) and a new value of the coefficient S,, was determined as 18.9220.42X 10M sq cm per dyne in lieu of the value originally reported of 18.82x10 sq cm per dyne. This new value of S, leads to a new value of S, of — 9.43 X101" sq cm per dyne. The values of the other coefficients are unchanged. results. This value compares with the value of 12.3X10 sq cm per dyne reported by Schmid and Boas? The new results are summarized in Table 11. These results follow similar qualitative trends, previously published,&apos; relative to the effect of zinc content. However, the derived values of C11, C,, C,, and K are so sensitive to the uncertainty in the first decimal place of the S, values that they are probably not useful. This uncertainty must also apply to the previous results of Masima and Sachs," who obtained S, values from a similar extrapolation drawn wholly above their data points. Acknowledgments Advice and assistance on the statistical methods were obtained from R. W. Guard. The calculations were carried out by Miss E. Saacke.

Jan 1, 1958

By S. F. Radtke, J. A. Snyder, R. M. Scriver

DISCUSSION, J. R. Long presiding R. I. Jaffee (Battelle Memorial Institute, Columbus, Ohio)—The authors have written a fine and important paper, and are to be congratulated. I do not entirely follow their discussion of the relationship between the ductility of titanium and its crystal structure. Since high purity titanium is extremely ductile, being capable of cold reductions of ovei- 99 pct, its ductility cannot be unduly restricted by its hexagonal crystal structure. It is true that interstitial solid solutions of nitrogen and oxygen do have a restricting effect on ductility, but this would appear to be an alloying effect rather than a crystal structure effect. The point made by the authors concerning the relative ductility between forged and rolled titanium does not appear to be conclusive, either. It would appear that in the same condition forged material would have equivalent or better ductility than sheet material. The difference between the ductility reported for forged bar and annealed sheet in Table I may be the result of a greater degree of cold work in the as-forged condition. S. F. Radtke, R. M. Scriver, and J. A. Snyder (authors&apos; reply)—We appreciate the discussion by Dr. Jaffee. His point is well taken that the hexagonal structure of titanium does not, in itself, restrict the ductility of iodide material and, therefore, should not be limiting in this case. It is true, however, that the ductility of different grades of titanium is not necessarily related to their hexagonal structure but more likely to their orientation and composition. It is also true that the presence of small amounts of foreign elements in hexagonal metals may have more pronounced influence on ductility than a corresponding quantity in cubic metals. Average values from a large number of tests might show relatively better ductility for forged titanium than is recorded in Table I. The forged bars used in this work were tested in the annealed condition; little is known concerning the effect of forging practice on ductility in titanium metal.

Jan 1, 1952

Shoveling ore cost so much at Tyrone during the year 1917 that it was deemed advisable to conduct tests to see where the fault lay. These tests were in the nature of time studies and extended over a period of very nearly a year. No data were available on this work to supply a starting point, so it was necessary to begin in a very elementary way, to find out the capacity of the average Mexican laborer. To&apos; obtain a basis for comparison, it was necessary to determine the capacity of various types and sizes of shovels, so as to know whether the 21-1b. (9.5-kg.) load was the best load underground as well as on surface. A list of essential factors influencing shoveling was also made out during the course of a short series of preliminary time studies, and the motions involved in shoveling were analyzed and subdivided for convenience in studying. The necessary forms and record sheets were also decided upon at this time. A second short series of tests was then conducted on the surface, so as to be able to estimate the negative effects of underground work on the shovelers, and to minimize, as far as possible, the need for studying obviously poor types and sizes of shovels under the difficult conditions to be encountered in the mine. The test work underground consumed by far the greater proportion of the time and was divided into three series: Shoveling directly into a chute; shoveling into a wheelbarrow and tramming to a chute; and shoveling into a car and tramming to a chute. In each series the following points were determined for various lengths of time worked: Number of shovelfuls handled per minute, effect of distance thrown on shoveling speed, amount of rest required, amount of time consumed in tramming and dumping, proportion of working day occupied in shoveling, total tonnage handled during various working periods, effect of distance on tonnage handled during the day.

Jan 2, 1919

By J. H. Bowden

The water-hoisting tanks herewith illustrated have been designed for removing large quantities of water from recently-flooded mines, through their hoisting-slopes, with rapidity proportional to the capabilities of the hoisting machinery available, the tanks being adaptable to slopes of small sectional areas and varying pitches. The following features may be of interest to those operating mines liable to be flooded. 1. The arrangement of doors on each tank by which it may be automatically filled by immersion at any point on the varying pitch of a slope, the water being retained while hoisting on the flat as well as on the steep pitches, and quickly and autoniatically discharged at the top. 2. The arrangement, in connection with the above-mentioned doors, of side-wheels over the rear wheeh of each tank and of sidedumping tracks at the top of the hoist, for the automatic emptying and quick return of the tank. 3. The arrangement of two or more tanks, one in front of the other, so as to give as large a capacity in a single hoist as the enginepower will permit, yet without making any tank too large for the sectional area of the slope, or of unwieldlp length, or of such a shape that it cannot easily pass over vertical curves; and without concentrating too much weight on any one pair of wheels or on any point of the track. The details of construction and method of operating are shown by the accompanying sketches (Figs. 1 and 2), and the following more detailed description. At the end of each tank is a large iron door of almost the full size of the end of the tank, opening inwards, so that when immersed the tanks fill almost instantly. To provide for holding the water while it is hoisted up flat pitches, a wooden door is attached to the front of each tank, opening outward. Each front door is attached to the

Jan 1, 1892