Search Documents

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.' This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969

Discussion of the paper of Frederick W. Apgar, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 7S, June, 1913, pp. 1011 to 1022. L. C. GRATON, Cambridge, Mass.:-I presume I am one of the few who are exceedingly interested in microscopic work, and I am sure we have all enjoyed this paper very much. I will not attempt to express my own feelings in regard to it beyond saying that it seems to me that this sort of investigation and study has been overlooked and slighted, and its possibilities are very great. There are one or two, details which impressed me, because they were novel to me, and one was the development of secondary galena with dull luster. I have never seen any galena which seemed to be secondary, and have never seen any that was secondary or primary that did not have a bright luster. KIRBY THOMAS, New York, N. Y. (communication to the Secretary *) :-The present-day mining engineer is expected to " see into the ground farther than the point of the pick " and he is justified in making free claim to his ability to do so. Mr. Apgar has recorded the development of the application to the work of the engineer of a very useful but tardily recognized instrument-the petrographic microscope, an instrument which is helping to shatter the proverbial "point of' the pick" limitation-and he has shown its use and its possibilities very clearly. Some further field examples of the use of the microscope in engineering problems may add to the appreciation of Mr. Apgar's scholarly paper. In exploration by diamond drills in the Sudbury, Ontario, nickel district it is often of great importance to determine when the drill has passed out of the norite and into the foot-wall formation. Structural calculations may give a clue to the expected point of contact, but the variations are considerable, and, since to stop the drill before reaching the contact is futile, and too continue beyond it is needless, it becomes of theoretic and economic importance to determine positively the lithological nature of the corer at critical stages in the work. In some places the foot-wall is an earlier norite, only distinguishable from the nickel norite (Sudbury-: ite), by means of an examination of the rock slides with a petrographic; microscope. Again, certain diabase dikes which cut the norite and. the foot-wall formations cannot be easily or with certainty distin-

Jan 11, 1913

By John Randall

IT is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless. of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary to first consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size at the right-hand side of the diagram and .measuring toward the left. This is not altogether convenient and might he changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, snaking it less convenient for most purposes, and for that reason the method here discussed is the well-known one based oil the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although .not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal. parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have rioted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series 'of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 9, 1917

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,' the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen' to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By Robert J. White

Strong&apos;s equation for calculating bottom-hole pressure reduction due to gas cutting of drilling mud is corrected, resulting in a simpler equation which is easier to use. Use of the equation is illustrated by examples. It is shown that reduction of weight of a 10 lb/gal mud by 50 per cent at the surface due to gas cutting produces only n 3 per cent decrease in hydrostatic head at the bottom of a 5,000-ft well. It is also shown that at the surface 5 volumes of air per volume of mud are required to reduce the apparent mud weight from 8.5 to 6.5 lh/gal in a 3,000-ft well. Illustrative graphs are included to show the effect of various degrees of gas cutting on apparent mud weight at depths of 2,000, .5,000 and 10,000 ft and to show variation of apparent mud weight, with depth for a 100 lb/cu ft (13.37 lb/gal) mud gas cut to 90 lb/cu ft (12.03 lb/gal) at the surface. INTRODUCTION In 1938, Strong&apos; published the following equation for calculating reduction in bottom-hole pressure due to gas cutting of drilling mud h = 1/D [p + pn/100 In p + p(1-n/100)/p(1- n-100)] where: h = depth in feet P = pressure in atmospheres at depth h due to mud column only D = hydrostatic pressure in atmospheres of a col-umn of uncut mud 1 ft high p = back pressure at well-head (in atmospheres) n/100 = fraction by volume of gas in mud at well-head at back pres-sure p This equation was recently found to contain an error due to an incor-rect expression for variation of vol-ume fraction of gas with pressure. Values calculated by the original equation are close to the correct values for small percentages of gas for which it was derived but become increasingly erroneous as the gas content increases and are completely unusable at the very high gas con-tents employed in aerated mud. DERIVATION The nomenclature used is the same as in Strong&apos;s paper. The pres-sure dP exerted by a lamina of thickness dh at a depth h ft is ex-pressed by Eq. 1 where x = volume fraction of gas at depth h dP = D (l - x)dh . . . (1) When we express x in terms of the wellhead per cent gas n, the well-head pressure p and the pressure P at depth h, the result is Eq. 2. x = (np/p+p)/(100-n) + (np/P + p) When this is substituted in Eq. 1 and rearranged to separate the var-iables the result is dh = 1/D [dp + np/100-n dp/(P + p]. Integration between appropriate lim-its results in or if the wellhead is open so that p = 1 atm and we rearrange Eq. 4, the result is loss in head = hD — P = n/100-n In (P + 1) ...(5) Eq. 5 can be solved easily by successive approximation using hD as a first approximation for P on the right-hand side and calculating a first value for loss in head. This can then be used to get a new value of P using the left-hand side of the equation. Values converge very rap-idly even for quite large values of per cent by volume gas n. EXAMPLES The effect on bottom-hole pressure of 50 per cent gas cutting of the mud in a 5,000-ft well using 10 Ib/ gal mud will be calculated, we have: h = 5,000 ft 10 X 7.48 144 X 14.7 = 0.0353 atm/ft hD = 176.5 atm n = 50 Substituting these values in Eq. 5 and using hD as a first approxima-tion of P on the right, we have, approximate loss in head = 50/50 In (176.5 + 1) = 2.30 log 177.5 = 5.17 atm. We calculate a new value of P as follows:

Jan 1, 1958

By Norman L. Wimmler, H. G. Iverson, S. Ricker, P. E. Oscarson, S. H. Lorain

THIS paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. CLAY EXPLORATION BY THE BUREAU OF MINES Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Lone, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d&apos;Alene, Idaho; the Whiteware deposit near Lewistown, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. THE CLAY DEPOSITS The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1944

By AIME AIME

AS director of Battelle Memorial Institute and as Chairman of the important O.P.M. advisory committee on metals and minerals, Clyde E. Williams numbers his acquaintances in the mineral industries by the thousands and h because his principal hobby is liking human beings, most of his acquaintancs are also his friends. Clyde is one of the many outstanding metallurgist, in the United States who started as a chemist. After graduating from the University of Utah in 1915 he was successively chemist for U.S. Smelting Refining and Mining Co., and at the Bureau of Mines station at Ithaca, N.Y. He then got into, metallurgical work and in 1920 he was appointed superintendent of the Northwest Station of the Bureau of Mines at, Seattle. Subsequently he was assistant to H. Foster Bain in metallugical work for the

Jan 1, 1942

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By David E. Jones, Dean K. Hunt, C. Y. Chen

INTRODUCTION Of all the numerous geological hazards that threaten the well-being of urban areas in the United States, probably none is so widespread, persistent, and diversified as surface subsidence (HRB-Singer, Inc., 1977). Simply defined, subsidence is the vertical displacement or sinking of the ground surface caused by either natural phenomena or man&apos;s activities. The downward movement, however, can be accompanied by horizontal movement, strain, tilt and even by a locally upward movement. Damage to structures and the environment can result from any of these movements. Extracting subsurface materials, fluids and solids, accounts for most man-induced subsidence in the United States. Among all the mining-related subsidences, the collapse of voids created by underground coal mining has been the major cause in inflicting surface damage (Comptroller General of the United States, 1979). Subsidence from coal mining may occur within a few weeks or be delayed for years, depending upon the mineral layer&apos;s depth below the surface, the overlying rock strata&apos;s characteristics, the extent and methods of mining that were employed, and the time deterioration of pillar and mine structure. Unless underground resources are not mined or control measures are implemented to prevent or minimize damage, some degree of surface subsidence and its accompanied deleterious effects are often inevitable. The ways to control the subsidence and minimize surface damage may include: 1. Precautionary measures built into new structures or surface features. 2. Preventive works applied to existing structures or surface features. 3. Mine design incorporating special underground layouts. 4. Any combination of the above measures. Upon the enactment of Public Law 95-87, the Secretary of the Interior, through the recently created Office of Surface Mining (OSM), was authorized to promulgate rules to regulate mining reclamation including subsidence control. Proposed on September 18, 1978, these rules were finalized, following public comment and hearings, on March 13, 1979, as part of the permanent regulatory program for the regulation of surface mining and reclamation operations which include the surface effects of underground mining. On January 28, 1981, Secretary Watt of the Department of the Interior issued an order to re- quire all agencies to identify with recommendations all regulations which are believed to be excessive, burdensome or counterproductive. Also on February 17, 1981. President Reagan issued Executive Order No. 12291 requiring all Federal agencies to conduct a regulatory review to make a determination that each promulgation of a regulation is clearly within the authority delegated by law and consistent with Congressional intent (Federal Register, 1981). As a result, OSM initiated the regulatory reform to revise the permanent regulatory program. Following a brief discussion of the technical aspects and the effects of subsidence on man and his environment, this paper presents a historical overview of how rules and regulations are used to govern the subsidence related problems. The development of the regulation of subsidence under Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977 (SMCRA or the Act) are also discussed, including the new regulations being developed under the regulatory reform program. SOME TECHNICAL ASPECTS Am EFFECTS OF FINE SUBSIDENCE An extensive historical review of mining subsidence is given by Zwartendyk (1971) and Shadbolt (1978). Comprehensive technical presentations have been given by Henry (1956), King and Whetton (1957), Hall and Orchard (1963). Muller, et al. (1968). Grard (1969), Voight and Pariseau (1970). Kapp and Williams (1972), Cummins and Given (1973), Brauner (1973) , and NCB (1975). A theory of surface subsidence due to underground mining was perhaps first fundamentally stated by a French engineer, Toillez, in 1838, and formulated by a Belgian engineer, Gonot, in 1839 (Goldreich, 1913, cited by Zwartendyk, 1971). Since that time,

Jan 1, 1982

By Charles Berry

Conventional and nonconventional insurance is examined from the point of view of a financier of a major mining and minerals project. The paper reviews the elements of a conventional insurance program; explains why such a program is not fully responsive to the project financier&apos;s needs; examines some of the new insurance coverages that can supplement a traditional program; and emphasises that these insurance markets are still in the early stages of their development with consequent effects on capacity (insured amount) and to some extent price (insurance premium).

Jan 1, 1985

By M. P. Sidorova, D. A. Fridrikhsherg

The surface charge, electrokinetic potential and surface conductance were studied for silica, alumina and rutile as the functions of PH and concentration of 1-1 electrolyte solutions. The adsorption potentials of potential-determining and specifically adsorbed ions were calculated from isoelectric and zero charge points on the basis of Stern equation and thermodynamic description. From surface conductance and charge data the mean ionic mobilities in double layer were estimated. The results give some information about the real structure of oxide-electrolyte interface and gel-layer concept.

Jan 1, 1980

The thirty-second annual meeting of the Montana Society of Engineers was held at Great Falls, Mont., on Apr. 10-12. The first day was given to the reception of visitors and the second day to the inspection of points of engineering interest. On Saturday, at the business meeting, the following officers were elected: President, Samuel Barker, Jr.; first vice-president, Charles A. Lemmon; second vice-president, George T. McGee; secretary and librarian, Clinton H. Moore; treasurer, Harry H. Cochrane; trustee for three years, Theodore Simons.

Jan 6, 1919

By S. G. Lasky

Abraham Lincoln is reputed to have said that if you want to chart a course to some destination, you have to know where you are starting from. In this instance we have to define our starting point in a double manner: 1) What was the theoretical basis of the Paley predictions? 2) What actually did the Commission predict, so that we can see how the predictions have worked out up to now as a basis for considering how they may have to be changed.

Jan 3, 1960

By J. J. Rutledge

I. Description of the Clinton Ores and Associated Rocks. The Clinton rocks in Stone valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.&apos; A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the upper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Jan 1, 1910

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By Richard E. Chism

I have thought it well to lay before the Institute some account of the Vallecillo Mines, now, I believe, the only paying ones in American hands in northeastern Mexico, including the States of Nuevo Leon, Coahuila and Tamaulipas. The authentic history of these mines dates from their ownership by an American Company in the year 1851, when they were bought by the Vallecillo Silver Mining Company of New York. They had been worked before by the Spaniards, but had been abandoned for many years, on account of the heavy expense of drainage and the constant incursions of the Indians. The company commenced work with several well-known New York capitalists among its stockholders, and had a large fund of both money and enthusiasm. The first point of attack was at a shaft on a mine known as the Jesus Maria, which had the most favorable traditions. Extensive buildings were put up, and two sets of pumps were successively tried. After the second pump, with a steam-cylinder 5 feet in diameter and 10 feet stroke and a plunger 20 inches in diameter, had failed to do more than hold the water, with infinite labor, at the 250 feet level, and after a thorough exploitation of the whole mine above that level had failed to yield more than some $30,000 worth of ore, it was resolved to abandon the effort. Operations were accordingly transferred to the old Dolores shaft, at a point about 21/2 miles to the

Jan 1, 1885

By R. S. Lewis

IN a recent study1 of the evolution of engineering education 1870 was taken as the initial point, as it is said to mark the transition from the poineer era in American engineering education to an era of rapid growth and consistent development. Prior to the founding of Rensselaer Polytechnic Institute in 1824, West Point Military Academy was the principal source of formal engineering training. In 1849 Rensselaer revised its program on the model of the leading French technical schools. Lawrence Scientific School was estab-lished at Harvard and Sheffield Scientific School at Yale in 1847. The University of Michigan pioneered in en-gineering instruction in the West, offering its first course in 1853 and awarding its first degree in 1860. Other important steps in -the progress of engineering education were the founding of Columbia School of&apos; Mines in 1864, the opening of Massachusetts Institute of Technology in 1865, and the founding of Cornell Uni-versity and the Thayer School of Civil Engineering at Dartmouth in 1867. From its organization in 1852 until 1871 the Ameri-can Society of Civil Engineers was virtually the only national society of engineers. In 1871 the American Institute of-Mining and Metallurgical Engineers was founded, to be followed later by the Mechanical En-gineers in 1880 and the Electrical Engineers in 1884. This expansion and diversification of the engineering profession was paralleled in the colleges, and by 1885 the plan of different curricula in the major branches of engineering was soundly established.

Jan 7, 1927

By L. G. Huntley

Points out differences between the new, more liberal, law passed by the Colombian Congress and the law passed in 1919, gives a few facts about the pipe-line concession granted to a Canadian company, and tells of new drilling developments. PROBABLY the most important development in the Colombian oil situation during the past year was the passage by Congress of a new petroleum law, which went into effect Jan. 31, 1923. The principal points of interest in which this new law changes or improves the previous one are as follows: Law 120 of 1919 provided that one person or corporation could not acquire more than three exploitation zones. of 5000 ha. each, and royalties were based on a sliding scale, to wit: 6 per cent. royalty on lands 400 km., or more, from the ocean; 8 per cent. on lands 200 but not over 400 km. from the ocean, and 10 per cent. royalty on lands located less than 200 km. from the ocean. Rentals were fixed at 10 centavos per hectare for the first year; 20 centavos for the second year; 50 centavos, third year, and $1 (one peso) yearly thereafter. Under this law the term of the lease was fixed at 20 years and, at the discretion of the government, could be extended for 10 years additional. After the expiration of the lease and its corresponding extension, the machinery and other material placed upon the property would vest in the government. A bond of 20,000 pesos was also required of the lessee to guarantee faithful performance of his contract.

Jan 3, 1924