Search Documents

By J. Jones-Parra, J. C. Calhoun

INTRODUCTION The purpose of this paper is to present the results obtained by solving the fractional flow' and frontal advance' equations to obtain oil recovery at water breakthrough as a function of the length of the system being flooded, the linear velocity of injection and the displacing phase viscosity. The method of solution makes use of the stabilized zone concept first presented by Terwilliger, et al3 when calculating saturation distributions in a gravity drainage system. In order to check the calculated results, the equations and method of solution were applied to the system on which Rapoport and Leas' reported experimental data. METHOD OF SOLUTION The solution of the fractional flow equation and the frontal advance equation is obtained by assuming that a water front forms to sweep the oil out ahead of it. There is ample evidence that under the proper conditions a water 'front does form. If this water front is not to dissipate, the water saturations which comprise it must have equal linear velocities. These water saturations are said to comprise the stabilized zone. Equation (2) indicates that for all these saturations and hence fw must plot as a straight line against saturation for those water saturations comprising the stabilized zone. The water saturations lying between the highest in the stabilized zone and the highest that can be achieved in the porous medium comprise the variable zone. Regardless of the numerical value of the length of the system, the variable zone must eventually span all of it, so that for long enough systems in Equation (1) will be small enough to be neglected. Hence, for the saturations in the variable zone Equation (1) can be simplified to In order to determine the composite fw function applicable to the entire range of saturations in the porous medium, it is necessary to find the water saturation which separates the stabilized zone from the variable zone. This dividing saturation must be on the curve defined by Equation (4), and a tangent curve at that point must pass through the initial water saturation to satisfy Equation (3). Hence, the valid fw curve is given by a straight line starting at the initial water saturation, tangent to the curve of Equation (4): and along the curve of Equation (4) from the point of tangency on. The point of tangency determines the water saturation dividing the zones. The length and shape of the stabilized zone can be found by solving Equation (1) for Integrating this expression numerically between any two saturations in the stabilized zone gives the distance separating these two saturations. By repeated integration, the saturation distribution of the stabilized zone can be determined. The total length of the stabilized zone is given by The integral appearing in Equation (5) is a function of the viscosity ratio, the capillary properties of the rockfluid system, the relative permeabilities, and the initial water saturation. Considering these variables fixed and designating the value of the integral by writing caw for and v/60 for q/A; Equation (5) becomes The saturation distribution of the stabilized zone can be integrated over its length and divided by the length to obtain the average water saturation The volume of water in the stabilized zone is then given by The average water saturation in the variable zone can be found by extending the straight line segment of (the segment joining Sw and Sw) until it intersects fw = 1.00. The saturation at the intersection is. This method of finding is nothing more than the graphical solution of the equation The volume of water in the variable zone at breakthrough is then given by Assuming no initial water saturation, the recovery at breakthrough expressed as percent pore volume is given by

Jan 1, 1953

By Larry Kaufman

A useful method for estimating the entropy of NaCl type compounds has been developed by combining the Debye theory of specific heat with the Lindemann formula. This method pemnits calculation of the entropy from a knowledge of the atomic weight, atomic volume, and melting point of the compound. Comparison of the calculated and observed entropies of 35 NaCl type compounds over a wide temperature range yields good agreement thus establishing the usefulness of the method. Application of the method to other crystal types is also discussed. KUBASCHEWSKI~ has suggested a useful method of estimating the enthalpy of formation of inter-metallic compounds from a knowledge of the crystal structure, lattice parameter, and heats of sublimation of the component elements. This method is quite valuable in predicting the tendency for compound formation in a given system and is of particular value in considering systems for which no experimental data are available. In order to supplement the enthalpy calculation afforded by Kubschewski's method, it would be of value to be able to estimate the entropy of compounds so that the entropy and free energy of formation could be evaluated. Although a considerable body of such data determined by calorimetric and equilibration techniques exists at present, the difficulty of making such measurements (particularly at high temperatures) and the ever increasing number of new compounds which are of interest make the desirability of such a computational method clear. This paper deals with a method for calculating the entropy of a compound from a knowledge of the atomic weight, atomic volume, and melting point. Since these data are generally easier to determine and therefore more readily available than thermo-dynamic data, they should provide an additional tool in estimating the stability and reactivity of compounds at high temperatures. I) THE ENTROPY OF PURE METALS As a first approximation, the specific heat of a pure metal can be represented by a sum of terms where C,($/tI is the vibrational specific heat calculated on the basis of the Debye theory, lo4 TC, (0/T) is an approximation to the Cp - C, correction. T is the electronic specific heat, and Cp (p) is the magnetic specific heat. Although the Debye theory does not provide a complete description of the vibrational specific heat, i.e., the Debye temperature 0 is not a constant, it does provide a good approximation when used properly. Blackman6'7 has written several reviews on this subject discussing the different values of 0 determined by various methods (specific heat, X-rays, elastic constants, electrical resistivity, and so forth), as well as the observed temperature dependence of 0 with T. In the present case the 0 in Eq. [I] naturally refers to the specific heat 0. The variation of Debye 0 (as determined from specific heat measurements) with temperature is observed to exhibit its most radical behavior at very low temperatures. At higher temperatures the 8 values are observed to become more nearly constant. Blackman6'7 has presented the variation of 0 with temperature for several metals. His tabulation is reproduced in Table I. Reference to Table I shows that above a certain temperature level, 0 remains fairly constant. The value of 0 which is most useful in computing the specific heat, and hence the entropy, is the value of 0 in the range 0/6 « T « 0. In 1910, Lindemann' suggested a relation for estimating Debye 0 values. According to this formula, where V is the atomic volume, T is the melting point in 'K, M is the atomic weight, and CL is a constant. Mott and Jones9 present this formula and state that there is at present no satisfactory theoretical explanation, but that it does have an empirical basis. By using the valuesof 0 in Table I along with known1' values of M, T, and the molar volume VM, where the Lindemann constant can be evaluated. This

Jan 1, 1962

R. Trimble, Pittsburg, Pa (communication to the Secretary) : There are in the proposed specifications only two points on which I wish to comment at this time.

Jan 1, 1902

By E. Seidl

THE basic material for testing aluminum, copper and zinc is a cast metal, principally in the form of wire bars (Figs. 1 to 3) and plates for the produc- tion of sheets or strips, (Figs. 4 to 7). Experience has proved that the chemical and crystallographic proper-ties of such cast metal exercise a certain influence when it is being worked, which is usually done while the metal is hot. In a chemical sense the slight impurities, which even the purest industrial metal contains, have a disturbing effect. They settle either along the outside limits of granulation, as in the case of aluminum and copper, or else in the interior of the crystal, as in the case of zinc; but frequently are also found accumulating at certain points (formation of the blowholes and skin) (Fig. 7). The crystallographic character of the metals is either that of uniformly fine granulation, or else there occurs a certain distinct casting texture marked by sharply defined cooling conditions and consisting of crys-tals of a pronounced stalk-like or blade form. Since we generally distinguish between a crystal texture and a crystal structure, the term crystal texture is used here for the arrangement of the crystals relative to each other and their microscopic composition; crystallic structure is used to mean the radioscopically ascertain-able structure of the crystal. The influence of the impurities and of the crystalline character on the working of the metals has been fre-quently pointed out in practice as well as in science.

Jan 11, 1927

By Norman P. Goss

What would appear to be a very simple process on paper has proved to be overrun with a multitude of unseen difficulties. For more than 70 years attempts have been made to cast metals in a continuous manner, but it has been only within the last Io years that some degree of success has been achieved.1 Historical Development Bessemer's Experiments—Method I Bessemer was the first to try to cast molten metal in a continuous manner. His method is fully described in U. S. Patent No. 49053, issued in 1865. The patent drawing is shown in Fig. I. In this method the molten metal was poured between a pair of rolls of large diameter, which were cooled by water sprays. Means were provided to prevent moisture from coming into direct coptact with the molten metal. The width of the strip was controlled by the flanges. On paper this should work to perfection, but it is beset with many difficulties still awaiting solution. Bessemer failed to reduce his invention to commercial practice. About 1890 Bessemer's method was revived by Norton and associates (U. S. Patent No. 441375). They formed the Fluid Metal Rolling Co. at Maywood, Ill., and spent $250,000 in endeavoring to develop the technique for this simple method. Finally they had to abandon it. Naturally, they did carry the technical development far beyond anything Bessemer had done, but even so it was far from being a useful commercial success. In recent years it has undergone further development by C. W. Hazelett (U. S. Patent No. 2058447), who has succeeded in obtaining long lengths of copper, brass, aluminum, and even stainless steel. He introduced many' ingenious devices but the greatest obstacle still remained—the disintegration of the roll surface when the surface is heated and chilled in rapid succession. Difficulty is also experienced in maintaining a uniform supply of molten metal to the rolls. The patents pertaining to this method would indicate these to be the major obstacles. Experimental work by Mellen—Method 2 A departure from the method introduced by Bessemer, was tried by Grenville Mellen, of East Orange, K. J., sometime between 1914 and 1920, who obtained a number of patents.2 His method is illustrated in Fig. 2. This method failed to make an impression upon the art; however, it is of value in pointing out the difficulties the inventor ran into and the way in which he tried to meet them. The split mold sections form two endless chains. When going through the center of the apparatus, these sections engage each other to form a complete mold. As the engaged mold section moves downward at a constant speed, molten metal is teemed into it. As this is going on, another set of cooperating mold sections move into position on top of the one being filled. The molten metal is teemed into the mold through a silica tube. According to the teachings of this patent, the level of molten

Jan 1, 1945

By N. H. Mannakee

SINCE the publication of the paper of Mr. Scholz, The Effect of Humidity on Mine-Explosions,' I have undertaken a study of the meager available data of barometric and temperature conditions it times of mine-explosions, and have arranged these data in a manner which may be of interest to other students of mine-explosions. This study covers the period from 1898 to 1909, during which an ever-increasing percentage of collieries has been ventilated by fans giving air-currents of high efficiency. Previous to 1898 this percentage was smaller than at any time since. The vari¬ous States have become, from time to time, more exacting in their demands upon poorly-ventilated mines. This general im¬provement in ventilation throughout the Appalachian field has undoubtedly brought about a condition which is annually the cause; .or a very important attendant, of the high percentage of fatalities in mine-explosions, through the daily passage of from hundreds to thousands of gallons of water, invisibly suspended in the air, carried out of the mines by the ventilating-currents during the existence of certain temperature- and humidity-conditions. There is a wide-spread opinion that these conditions exist from November 1 to March 31; but it is more likely that they have a much wider range, which varies from year to year. Certain years show an increase or decrease of rain-fall from the mean ; the daily temperature may fall far below or rise far above the mean established by a record of a period of years; and the daily humidity varies likewise. If mine-explosions are influenced by a lack of moisture in the mines, certainly it may be expected that the influence will be felt at times when the

Nov 1, 1909

By J. M. Roberts, D. M. Barnett

The activation energy required to break a pinned dislocation line away from its condensed atmosphere of impurity atoms is calculated as a .function of applied stress, without neglecting line tension. Reasows are presented for not assuming the effect of line tension to be negligible when considering the problem of freeing a small segment of dislocation from an impurity atmosphere. The dislocation is considered to he pinned at each atomic size along its length and the pinning points are assumzed immobile. The development is a refinement of the origznal cottrell-bilby1 theory. The solution is compared to recent approximations developed by cottrell3 and Haasen5 in which line tension con- IN 1949 Cottrell and bilby1 considered the problem of determining the force required to pull a dislocation away from its condensed atmosphere of impurity atoms. They also examined the effect of thermal fluctuations on this force. The dislocation line was pictured as bowing out in a triangular loop under the action of an applied stress, and the activation energy necessary to free the dislocation from its atmosphere was calculated as a function of stress, line energy, and dislocation-solute atom interaction. siderations were neglected. A qualitative explanation of the yielding process in terms of the activation of Frank-Read sources is presented, but the lack of a realistic solution to the dynamic dislocation problem involved prevents an extension of the model at present. A self-consistent correlation between the present calculations and experimental data for delay time associated with yielding and the temperature dependence of the upper yield stress was made. Favorable agreement was noted. It is concluded that extension of the original Cottrell-~ilby' theory which includes line tension effects can just as well describe the yielding process as other approximations3,5 which neglect line tension. Cottrell and Bilby found the form of the activation energy vs stress curves to be almost independent of the line energy and the interaction energy (i.e., these parameters only affected the activation energy U by a scale factor). A check of the theory was accomplished by comparison with the experimental data of McAdam and Mebs2 for the lower yield stress as a function of temperature. cottrell,3 in 1957, attempted to obtain a simple closed-form solution for the activation energy as a function of stress by linearizing the quartic equation relating displacement of the dislocation line and applied stress. It was argued that since the contribution to the line energy/atomic plane of a dislocation is made by the long-range stress field of the dislocation through a term of the type (Gb3/2p)ln A/ro, where

Jan 1, 1963

By AIME AIME

AN enthusiastic crowd, cheerfully confident that the upturn in the oil industry has arrived, gathered in Los Angeles on Sept. 29 for a Petroleum Division meeting arranged by the Southern California Section. The assembly room of the California Oil and Gas Association was the place of meeting. H. Norton Johnson was in the chair for the morning session, with about eighty members and guests present. Four papers were presented before lunch and a fifth, on electrical coring, was withdrawn as the work on which it was based is still confidential. Joseph Jensen read his contribution on the "Kettleman Hills Middle Dome Unit Plan" and, as he had an active part in framing the plan, his outline and discussion of it was authoritative and informing. J. H. Woods asked concerning the operation of the casing-head gasolene plant under the plan and was informed that one company would operate the plant and royalties would be paid participating companies

Jan 1, 1933

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By Frank R. Corwin, Selden S. Rodgers

PAGE I. Introduction,........... 383 11. Brief History of Present MacDoUgall Plant,.... 384 III. First Experimental Work on Increasing Capacity of Furnaces, 385 IV. Effect On MacDouRall Plant of IncreaBed Draft from New Smelter Stack,,.......... V. Increasing the Capacity of the MacDouGall FurnaceS,.. 391 (A). Test of Arthur Crowfoot on Increasing Capacity,.... (a). Description of Test,........ (6). Discussion of Results Obtained from Test,... 393 (B). Investigation Carried Out by John A. Church, Jr.,... 395 (a). Advantages of High Speed,......398 (C). Effect on Regular Operation of Department by Applying Results Obtained from Experimental Work ..... 399 (D). Fundamental Principles Involved in Increasing the Tonnage, . 400 VI. Treatment of an INcreased Amount of Ore Screenings,.. 401 VII. Maximum Percentage oF Ore Screenings in a MacDoUGall Feed, 403 VIII. Tests to Further Increase Capacity of Furnaces,... 406 IX. Tests to Decrease PercentaGe of Flue Dust made by MacDouGall Furnaces,............. (A). Repath-Marcy Furnace......... 408 (B). Modified Hepath-Marcy Furnace,....... (C). Crouse Furnace Designed for Dust Prevention,.... 413 (a). Tests on Crouse Furnace,....... X. Concrete Hearths,.......... 419 XI. Conclusion,............ I. Introduction. Since the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces.has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 1, 1914

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By C. H. Bowen

NDUSTRY needs a generally applicable means of defining average grain size and grain size distribution. Students of sediments hade explored this field, employing methods that might also prove useful in engineering problems. Before attempting to solve specific problems it is well to review the derivation of commonly used grade scales and the reasons for their selection. This aspect of the problem seems largely to have been lost, and a review of basic factors may suggest causes for failures in using size analysis data. Three facts are implicit in selection of a grade scale: 1) Most particulate mixtures are continuous distributions of sizes, and any grade scale that may be employed is an arbitrary means of visualizing that distribution. 2) For purely descriptive purposes, any grade scale, regardless of the rationality of the class intervals, will be satisfactory if it is accepted by a sufficient number of workers. 3) For analytical purposes, class intervals must be small enough to define the continuous distribution accurately. Further, where statistical studies are involved, a fixed relationship should exist between classes or grades. An argument in favor of geometrically related size grades lies in the fact that most particulate mixtures contain such a wide range of sizes that use of an arithmetic diameter scale is practically impossible. Udden, who recognized this fact in 1898,&apos; proposed one of the first grade scales based on a regular geometrical interval. Udden used 1 mm as his basic diameter and a ratio of 2 (or 1/2) between classes. In 1922 Wentworth2 re-examined Udden&apos;s grade scale, retaining the same class interval and basic diameter, but extending the scale in both directions and renaming the classes. In 1930 (Ref. 3, p. 82) the American Society of Testing Materials proposed what is now known as the U.S. Standard fine sieve series, also based on the 1 mm diam, with a v2 ratio between sieves. This, then, is a one fourth Udden-Wentworth series in the sizes below the 4 mesh sieve. The U.S. Standard coarse sieve departs from the 1 mm base and uses inches; hence it is not a direct continuation of the fine series. The U.S. Standard series would thus seem to possess all the attributes of a good grade scale, which it is. It has a large number of classes (sieves). in fact too many for practical use in its entirety. This v2 subdivision of the Wentworth grades has led to the common use of two v2 sieve series, the half-Wentworth and the engineers&apos; series. Geologists and sedimentologists favor the half Wentworth, or 18, 25, 35, 45 sieves, etc., whereas the engineers, preferring round numbers, utilize the other half of the U.S. Standard grade scale in the 16, 20, 30, 40 sieves, etc. The fixed geometrical ratio between classes is an advantage in statistical analysis, but the unequal classes cause some complications in calculations. This is especially true when moment measures are used. It was to simplify these calculations that Krumbein in 1934 devised the phi scale. Phi is defined as being equal to —log2 of the diameter in millimeters. Selection of logarithms to the base 2 relate the phi scale directly to the Wentworth grade scale in such a manner that the whole or fractional diameter values 2, 1, 1/2, 1/4 mm, etc., become rational whole numbers, —1, 0,1, 2, etc. Since this is an arithmetic rather than geometric series, calculations are facilitated. When the logarithm is multiplied by —1 the phi values below 1 mm become positive, those coarser than 1 mm negative. Because of its relationship to the Wentworth grade scale (and in turn to the U.S. Standard fine sieve series) it is not necessary to use the transformation equation to calculate the phi value for each individual sieve; this can be done graphically as shown in Fig. 1. It should be noted that this graph may be extended in either direction to include the range of sizes most commonly used by the individual worker. Application to Statistical Analysis Any attempt at systematically relating size analysis data to properties involves a statistical study whether it is recognized as such or not. Since this is true it would seem more logical to use measures and devices related to the general body of statistical theory. Several methods are available for studying particulate mixtures. One of the most commonly employed, and also the most often misused, is the histogram or block diagram. If its limitations are recognized and provided for, the histogram is a very useful tool. According to conventional practice, the bars of equal width are plotted and the values noted in terms of diameters, when in point of fact, log diameter is implied by such notation. Further, the histogram is sensitive to choice of grade scale and size of class interval, either of which may color the result. Grade scales whose classes are not related by fixed intervals are particularly difficult. Another basic weakness of the histogram is that it pictures a continuous distribution as a series of discrete grades.

Jan 1, 1957

By Frank S. Gardner, Morris Cohen, Dara P. Anita

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By Morris Cohen, Dara P. Anita, Frank S. Gardner

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By AIME AIME

PETROLEUM technology was the sole subject of discussion at the meeting of the Petroleum Division at the Baker Hotel, Dallas, Texas, Oct. 6-7, except for the brief talks by President Becket and Secretary Parsons at the dinner on Friday evening. Even on this occasion, following the scheduled official features, it was in order to talk "shop." W. E. Wrather and E. A. Stephenson, respectively Chairman and Secretary of the Division, had planned for a meeting of this nature and by preference, apparently, the 122 who registered fell in with the scheme wholeheartedly. Not because the competent local committee had not provided for it, but by choice, the members just did not sign up for entertainment or field trips, but did attend largely the three technical sessions and engage in earnest discussion of the approximately dozen excellent papers. In this connection, and without question, the high lights of the meeting were the papers by Morris Muskat and R. D. Wyckoff, and Prof. W. K. Lewis. The former, entitled, "A Theoretical Analysis of Waterflooding Networks," had been entirely demathematized by the authors for presentation at this and the Los Angeles meetings; the author of the latter, which was on the "Physical-chemical Relationships of Hydrocarbon Gas-liquid Mixtures at High Pres¬sures," had airplaned to Dallas in the company of Dr. H. D. Wilde from Chicago in order to present his paper at the final session on Saturday morning.

Jan 1, 1933

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls&apos; hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls&apos; mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

By R. E. Schilson, F. H. Poettmann

The direct determination of the stabilized performance behavior of low capacity, slowly stabilizing gas wells is extremely time-consuming and wasteful of gas. From both field experience and theoretical considerations, a test procedure has been evolved by which the stabilized hack pressure behavior of such gas wells can he predicted without having to revert to long time flow tests. The method consists of using the isochrona1 test procedure to establish the slope of the back pressure curve, "n", and the short time variation of the performance coeficient, "C", with time. From this short time transient flow data and theoretical considerations, the value of C at large times can he established. By assuming the radius of drainage of a well to be half the distance between wells, one can calculate the stabilization time for various well spacing patterns. Once the stabilization time for a given .spacing has been determined, the value of C can be calculated and the stabilized back-pressure curve can he. establbrhed. The calculated perfortnance coefficient as a function of tinze was cotnpared to the experintentally measured values for a number of gas wel1.e. The deviation of the calc~*lated from the cxperimental res1tlt.s vary depending on the set of short time experimental points used to evabrate the parcrttzeters of the equation. The longer the tirne far the flow test data user1 in the calculations, the better was the agreement with the experimental results. The time necessary to obtain this data from well tests varies consitlerably, depending on the physical natrcre oj the rt3scrvoir under consideratiot~. INTRODUCTION For many years, the U. S. Bureau of Mines Monograph 7&apos; has served as a guide for testing and evaluating the performance of gas wells by means of the back-pressure method. The back-pressure performance of a gas well is expressed by the following equation: Q~ CW-W.........(I) where the characteristics of the back-pressure equation are determined by C, the performance coefficient, and n, the exponent which corresponds to the slope of the straight line when Q and {P* - PN2) are plotted on logarithmic paper. Q is gas flow rate at standard conditions, and P, and P, are equalized and flowing bottom-hole pressures, respectively. Prior to the development of the back-pressure tcst, the "open flow" capacity method of testing a well was common. By this method, the wells were flowed wide open to the air and the flow rate measured. Such procedure was wasteful of gas and did not provide information on the deliverability of the gas to the pipe line. Monograph 7 Procedure The back-pressure method of testing wells was developed to overcome these shortcomings. Although much has been learned regarding the laws of the flow of gas through porous formations, the original development of the back-pressure relationship was based entirely on empirical methods. The back-pressure behavior provides the engineer with information essential in predicting the future development of a field. It permits him to calculate the deliverability of gas into a pipe line at predetermined line pressures, to design and analyze gas gathering lines, to determine the spacing and number of wells to he drilled during the development of a field to meet gas purchasers&apos; requirements, and to solve many other technical and economic problems. As described in Monograph 7, the flow-after-flow method of back-pressure testing, when applied to fast stabilizing and usually high capacity wells, correctly characterized the behavior of the well. However, as the value of the gas at the wellhead increased, small capacity gas wells having slow rates of stabilization became economically operable. The flow-after-flow method of testing could not be used to describe the behavior of these slowly stabilizing wells. The procedure of Rawlins and Shellhardtl for establishing the back-pressure behavior of a gas well was based on the rcquirement that the data be obtained under stabilized flow conditions; that is, that C is constant and does not vary with time. C depends on the physical properties of the reservoir, the location, extent and geometry of the drainage radius, and the properties of the flowing fluid. In a highly permeable formation, only a very short period of time is required for the well to reach a stabilized condition, and, consequently, the requirements for the test procedure described in Monograph 7 are met. For a given well, n is also constant

By Wallace Thorneycroft

FOREWORD This paper by Mr. Thorneycroft, Past President of the Institution of Mining Engineers (Great Britain), and chairman of its Subsidence Committee, is a valuable contribution to the assemblage of data on ground movement and subsidence from coal mining. It deals with the effects of advancing longwall, a method almost universal in Europe but as vet little used in the United States outside of Northern Illinois and in a few scattered places elsewhere, in thin coal beds, as in the Lexington field, Missouri, Canon City field, Colorado, and the Birmingham field, Alabama. Although by advancing- longwall, a maximum recovery of coal is obtained and it has to be employed where there are weak shale roofs, especially in deep mines, it is a more expensive method of operation unless the mining conditions are favorable, which is unusual in the United States. On the other hand, there is a growing use in this country of what is essentially retreating long wall, with an approximately straight break-line as described by Rayburn.1 With this method, in which the pillars are substantial, it was shown that the ground movement effect is practically identical with that of advancing longwall, hence the value to mining engineers of the precise data given by Mr. Thorneycroft. His study is unusual in several respects; it deals with conditions connected with ,the mining of a coal bed 20 in. thick, about 490 ft. below the surface, over a mined-out area in a 5-ft. bed about 90 ft. below, which had been mined about 12 years earlier. Both mines passed under Plean House, a building of massive cut stone construction built over a century ago, in which Mr: Thorneycroft resided throughout the under-mining period. Slight cracks opened in the walls as the longwall face approached the house in mining the upper seam, and closed after the face passed and subsidence took place. In the northwest wall, the last wall the face passed under, some stone blocks were broken, which was attributed to a strike period when the advance of face came nearly to a standstill. Other than this there was no perceptible permanent damage, as indicated by the photographs taken by the undersigned in 1923 (Figs. 1 and 2). Mr. Thorneycroft used a novel means of studying the successive positions of the corners of the building: he hung plumb bobs from the eaves and traced the paths of the respective plumb bob points on level surfaces. The angles made by the house walls with the plumb bob lines gave measures of the slope of the subsidence wave at the respective points. A slight upward wave was indicated by the surveys ahead of the subsidence, which would appear to be due to a tilting over of the massive sandstone stratum in the roof measures near the surface, the edge of the subsidence area acting as the fulcrum.

Jan 1, 1931