Search Documents

By Osvaldo Guilherme Comineli

While the hot cracking of Cu-containing steels is a serious and widely known problem for the industry, the literature reports that copper only slightly impairs the hot-ductility measured in laboratory. A distinction is drawn between hot ductility and hot shortness and the respective cracking operating mechanism involved at the respective range of temperature. The representability of the laboratory assessment of hot cracking of Cu-containing steels by hot tensile tests compared with actual results in industrial practice is discussed. The effectiveness of the variable affecting in each cracking mechanism and respective temperature range, focused in improving the hot cracking assessment of Cu-steels and the relative importance of oxidation will also be discussed. It is concluded that the hot tensile test in argon might be a good simulation if properly interpreted and that the role of oxidation is secondary in causing hot shortness. A schematic diagram for the hot tensile test is proposed.

Oct 30, 2017

By Augusto César Barrios Tamayo

The high temperature erosion of Thermal Barrier Coatings (TBCs) is one of the main factors that define the lifespan in gas turbine components as it is considered the second source of failure of hot path components in power and propulsion turbine operation. The worn Top Coat (TC) surface in components such as first stage turbine blades affects the turbine efficiency due to energy losses and the increment in heat transfer to substrate. The first part of this work consists in describing a HTE test facility developed to emulate the damage conditions found in a number of components of gas turbines; in this testing machine, the samples were exposed to combustion gases moving at velocities close to 1.5 Mach and temperatures of 1100°C. The second part consists in the characterization of liners and first stage turbine blades of a GE7FA gas turbine used for power generation. The last part deal whit correlation of the features of TC’s worn surfaces with the erosion conditions and the dominant degradation mechanisms between test samples and turbine components were compared.

Jul 31, 2018

By Daniel Carvalho, Marcos Viana, Leonardo Demuner, Herbert Castro

Intensive process and technology improvements related to the BOF converter — the key process to increase steel plant productivity and stability — have been performed at Ternium Brazil. This paper details the road map for process developments and investments in equipment technology, as well as the results achieved. The main topics of this development are the process control and optimization systems, slag forming model, oxygen blowing pattern, end-of-blow point control and slag carryover control. The outcomes of this development are improvements in the reblow rate, end-of-blow oxidation, direct tapping, slag carryover, slopping ratio, metallic yield and lining life.

Oct 1, 2019

By Carolina Gomes Dias Ribeiro

The modern composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace. Natural fibers composites with biodegradable polymer matrices are considered environmentally friendly materials and currently accepted as possible substitutes for synthetic composites. These green composites can be safely discarded or composted at the end of their life without harm to the environment. Another alternative for synthetic composites is to apply natural lignocellulosic fibers as reinforcement of conventional polymer matrices and already used in the automobile industry. In addition to the environmental and societal advantages of the green composites, the lignocellulosic fiber reinforced conventional polymer composite also has economical and technical advantages. In the case of a fiber collected as a waste, the price of the composite can be considerably lower than “fiberglass”. Furthermore, with high strength lignocellulosic fibers such as sisal, ramie and malva the specific strength of a composite may approach that of “fiberglass”. Therefore the objective of the present work is to investigate the mechanical behavior of polymer matrix composites reinforced with high volumes of natural malva fibers subjected to tensile stresses.

Aug 16, 2017

By Milan Terčelj, Matej Drobne, Urška Klančnik, Peter Fajfar

The study of oxidation behavior of High Chromium Steel material used for surface layer of work rolls was carried out. Specimens taken directly from the roll were subjected to thermal fatigue in the temperature range between room temperature and 500 °C up to 700 °C by using thermo-mechanical simulator Gleeble 1500D. Our observation was focused on the impact of oxidation as a principal mechanism of degradation of the roll’s surface layer - mainly on the characteristics of oxidation propagation in relation to the test temperature and microstructure constituents characteristics of the material. Oxidation is considerably accelerated by certain characteristics of eutectic and primary carbides, i.e. their size (area), composition, morphology, orientation regarding to the water-cooled surface, etc. In the presented paper selected cases where emphasized oxidation takes place are investigated, analyzed and explained. Obtained results thus represent a contribution to explanation of conditions which lead to acceleration of oxidation behavior that in turn can lead to chipping or even early spalling of material from the roll surface layer.

Oct 1, 2019

By Jan Lampke

Increasingly pelletizing discs are used for the recycling of dust and sludge. The applied pellet feed is highly variable, for example in terms of chemical composition, grain size distribution and raw density. These raw materials related factors lead to a destabilized pelletizing process, which initially must be homogenized through special mixtures, as well as the use of binders or additives. There are many possibilities to reach stringent restriction of material related target factors. On the one hand it is helpful to be flexible by changing the process parameters of the pelletizing disc. On the other hand, it is necessary to use a material-binder-formulation, which leads to a highly stable pelletizing process. The paper deals with an example of the use of agglomerating device, pelletizing disc, to prepare different dusts and sludges for material recycling. These dusts und sludges are mostly generated in metallurgical processes, e.g. sinterplant, blast furnace and steelworks.

Aug 16, 2017

By Lionel Loïc Limol

Polymeric materials, such as polyurethanes and rubbers, are widely used in the mining industry because of their moderate cost and excellent mechanical properties. Such polymers have been used mainly in transportation (conveyor belt systems and pipes coatings) and screening, for their appreciable abrasion wear resistance. Studies revealed the complex influence of test parameters, such as grit size and applied normal load, on the abrasion wear process for polymers. In this study, the abrasive wear behavior of several polyurethanes and rubbers were investigated at room temperature according to a rotary drum abrasion method (DIN 53516). Wear tests were carried out at 26 cm/s test speed and load value of 5 N and 10 N. Corundum paper grit varying from 60 to 400 mesh were used as an abrasive surface. After each test the mass loss of the pin was recorded and the wear rates were calculated from wear volume. The wear surfaces were investigated by scanning electron microscopy.

Jul 31, 2018

By Thorsten Müller

In order to increase the production of Advanced High Strength Steel (AHSS) as well as to fulfill the growing expectations of various industries served, steelmakers must have wide- ranging know-how in terms of plant technology, operation, processes, quality control and, last but not least, know-how for AHSS including certification procedures. MET/Con is highly focused on the production of coated AHSS with tensile strengths higher than 600 MPa. Common heating and cooling technologies are unable to handle high alloyed steel grades – pre-oxidation and rapid cooling technologies have been developed to face these new challenges. MET/CON and Drever International have the knowledge to produce newest steel grades with these technologies.

Jul 30, 2018

By Jochen Wans

BCT® - Belt Casting Technology is the new horizontal near-net-shape casting process to produce flat steel products. BCT is the revolutionary leap in casting technology, designed for the production of special and conventional steel grades. Within a partnership between Salzgitter Flachstahl GmbH and SMS Siemag AG, the worldwide first caster is now in operation. SMS Siemag AG (in cooperation with Salzgitter Flachstahl GmbH) has erected the first industrial-scale casting machine located at Peine steelworks. The lecture will start with an overview about the highlights of the BCT® process with regard to the mechanical engineering aspects, while the second part will present current commissioning results and operation experiences. Since December 2012, the BCT plant is running. Up to March 2015 more than 90 casts have been carried out, 26 with FeMn-alloys. Never before flat steel was casted in dimensions of 1000 mm * 15 mm and with casting speeds more than 14 m/min.

Aug 16, 2017

By Kenneth Williams

Economic drives dictate the exploitation of formerly less attractive ore bodies located close to or even beneath the water table. These ores can cause handling problems and expensive downtime of processing equipment due to their increased adhesive characteristics and are colloquially termed as “wet and sticky” ores. In order to gain a better understanding of the causes of poor handleability, experimental test methods for wall and inter-particle adhesion within bulk solids samples were developed and validated. The results confirmed that adhesion of bulk solid to equipment surfaces is mainly governed by capillary pressure. It can therefore be described using the Young-Laplace equation, which implies that adhesion is primarily dependent on the interfacial water between bulk material and the adhesion partner. Accordingly, the governing material parameters of adhesion are its capillarity and permeability, as these two characterize water transport to or from the interface of the adhesion partners. Furthermore a threshold for the classification of a material as wet and sticky based on the measurements of adhesion has been proposed.

Aug 17, 2017

By Jônatas Venancio Barbosa, Dagoberto Brandão Santos, Túlio Magno Füzessy de Melo

In this work, the mechanical and metallurgical behavior of titanium added ultra-low carbon (ULC-Ti) steel under hot and warm working conditions was studied by means of dilatometer compression tests. Double compression schedules were performed at temperatures between 700°C and 1000°C, inter-pass times of 0.5-100 s, and deformations of 0.5 and 0.3 in the first and second stages, respectively, with strain rate of 1 s-1. The analysis of the flow curves obtained allowed the evaluation of the softening characteristics of the steel. The softening and microstructure features indicate different restoration mechanisms depending on the temperature range. Static recrystallization with rapid microstructure restoration is observed at temperatures within the austenitic and intercritical field. Strain induced boundary motion and recovery mechanisms apparently control the restoration process in the ferrite region. In general, flow stress curves showed dynamic recovery behavior. Only the deformation in the intercritical region produced a peak in the flow stress curves. Isothermal holding tests associated with single hit compression indicated the presence of dynamic strain induced transformation, accelerating the softening kinetics at the intercritical region.

Oct 1, 2019

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By Waleska Campos Guaglianoni

With the growth of nanoscience and nanotechnology, the synthesis of nanostructured oxides has received a special attention. Metal oxides are widely used in the manufacture of microelectronic circuits, piezoelectric devices, fuel cells, catalysts, filters and bactericides systems. These metal oxides represent a large class of semiconductor materials suitable for photocatalytic processes. In recent years, new materials of this class such as TiO2 and ZnO have been developed due to their photo-catalytic abilities to degrade various environmental pollutants. This work aimed to evaluate the photocatalytic activity of zinc oxide previously synthesized by combustion synthesis in solution using citric acid as fuel and different reasons fuel/oxidant. After synthesis, the powders were subjected to heat treatments at different temperatures and photo-catalysis. The photocatalytic activity was evaluated by the degradation of a solution of methyl orange in a photochemical reactor of UV illumination, after which the transmittance of the samples measured with the assistance of a spectrophotometer. To analyze the results, a commercial zinc oxide was used as standard. The products of combustion synthesis in solution showed that photocatalytic activity varied according to the ratio fuel/oxidant and as a function of heat treatment. The results showed a higher photocatalytic activity for the products obtained with disabilities fuel in the reaction and heat treated.

Aug 8, 2018

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By Emanuele Osto

In late 2013, the installation of the world's first application of a break-through technology for rail hardening was started at Baogang Iron & Steel (Group) Co. Ltd. in Inner Mongolia, China, one of world's leading rail producers. The "Injector Dualphase Rail Hardening" (idRHa+) system was developed by Primetals Technologies and Centro Sviluppo Materiali S.p.A. (RINA-CSM) a Technical Center headquartered in Rome, Italy. Baogang was a key partner, providing its large expertise of premiumrail producer, including its experience with existing offline technologies. With a design based on thermal, mechanical and metallurgical models, idRHa+ can apply customized cooling protocols, so to obtain the desired microstructure and hardness distribution across the rail head, with a high degree of accurateness and operation flexibility. idRHa+ can be installed in inline or offline configurations. During 2014, the system was successfully commissioned at rail mill #2 in the city of Baotou, Inner Mongolia, and entered the regular commercial production. This paper gives an overview of the key concepts behind idRHa+'s design, the progression of its commissioning and testing till the ramp-up to consistent industrial operation. Derived from idRHa+ research and experience, other water-cooling technologies are available for different applications such as: quenching & tempering of medium-large sections, control of distorsion of merchant bars, quenching of stainless grades for improving the resistance to corrosion.

Aug 16, 2017

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Johanna Alegría-Ortega

Cr/CrN bilayer coating was deposited on AISI 440C by Cathodic Arc. The composition and structure of the Cr/CrN coating were investigated by scanning Electron Microscope, X-Ray Diffraction and X-ray Photoelectron Spectroscopy. The results show that crystal structure obtained was CrN phase with preferred [220] orientation. The hardness and adhesion of coating also were studied. The evaluation of erosion-corrosion (EC) on 440C bare and coated with Cr/CrN was performed by carrying out wear tests using a slurry jet with impingement angle 90° at 4 and 8 m/s. Corrosion, erosion and synergism wear rate were evaluated following the procedure described in ASTM G-119-09. This study presents that the synergism wear rate exceeds 40% of the total mass loss for coating and 60% of mass loss for the 440C, being the most aggressive wear component. The increase in impact velocity generated a rise in mass loss for both 440C bare and coated. The Cr/CrN coating offers better corrosion and erosion–corrosion resistance under all the tested conditions.

Aug 8, 2018