Search Documents

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By R Adofo

Underpinning the mining process is a continuum of prediction, specifically of tonnes, grade and recovery from exploration to grade control, through short-term mine design, to mining and processing. The interdependence of one activity on the other is so strong that it can be difficult to partition the activities and determine where there are issues, if any. Reconciliation is the process that compares the predictions of the various estimates to the actual product produced at the end of the production chain. Quite often, an attempt to understand the variances from one measuring point to the other creates a ‘wicked problem’.This study outlines the benefits of incorporating the principles of ‘systems thinking’ into the mining reconciliation process, by constructing a framework within which reconciliation is effectively managed. The philosophical base for any variances between successive links in the reconciliation chain cannot be attributed purely to the statistical variance between the predicted and the actual grades achieved, but should include the interrelationships between the technical and managerial professionals involved. Systems thinking, as an interdisciplinary approach, draws its ideas and concepts from a variety of disciplines, and in so doing can exploit their different strengths.The study described in this paper offers methodologies to analyse the task, in advance of developing a technical solution. Two systems thinking methodologies, Grounded Theory (GT) and Soft Systems Methodology (SSM) were employed. These methodologies, are geared towards dealing with relationships and interactions between individual parts and the whole. The GT coding in the study specified that the key activity that would drive the reconciliation process is through an effective reconciliation meeting, and the competencies of a ‘reconciliation team member’ This team member should be a good communicator and enjoy challenges, be open-minded and transparent, and have a broad perspective of the mining process and relationships across the different activities.CITATION:Adofo, R, 2017. A systemic approach to managing the Mine to Mill reconciliation process, in Proceedings Tenth International Mining Geology Conference 2017, pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Jan 1, 1882

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

This paper forms the second of a series, in which it is proposed to communicate the results of an extensive research into the influence of alloying elements on the physical properties of lead, now being carried out in the Metallurgy School of the University of Melbourne.Some general comments on this research were made by the present writer as an introduction to the first contribution by R. S. Russell*: It was there pointed out that it was the intention to prepare lead as pure as possible, to determine its properties and then to make alloys with the various elements added singly, and in various combinations, in order to determine the effect of each. This line of action is still being pursued.It occurred to the writer, however, that this fundamental attack might, with advantage, be accompanied by a parallel investigation in which lead of commercial purity would form the basis material. In this way, using a standard *Professor of Metallurgy, University of Melbourne.

Jan 1, 1934

By O. P. Garg

"The Iron Ore Company of Canada (IOC) operations in Labrador and Quebec, in Canada, is among the largest openpit mining complexes on a world wide basis. Since the 1981-82 recession, IOC has embarked on a comprehensive cost reduction and productivity improvement program in order to survive in the world iron ore market.This paper will outline the approach used in prioritizing the cost reduction items.IntroductionMuch of the mining industry in North America is in a crisis state. Most producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC) operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectively. A company owned and operated railway links this operation with the dock terminal facilities in Sept-Iles, Quebec.In the past decade the Iron Ore Company of Canada has been one of the largest producers of iron ore products in the world. Its pellets and concentrates as well as natural ores were sold in North America, Europe and the Far East. In 1981-82, sales, particularly in North America, went into a serious decline. For almost 30 years, the gospel IOC preached to employees was ""production, production!"" There were many innovations, and millions of dollars were spent on the biggest and best equipment, on research and development, on training and developing employees."

Jan 1, 1987

Factors of importance in the ntilization of coal fines are mentioned, and the results of flotation tests on coal fines from three important coal seams in New South Wales are presented.INTRODUCTIONEconomic utilization of fine coal is an important problem in the Australian coal industry, particularly as the proportion of fines mined is increasing with progressive mechanization.While the use of uncleaned coal fines may be economic, it may be preferable to beneficiate them, but the most economic process must be selected.For beneficiating coal finer than about 28 mesh, froth flotation can be applied, but mining engineers should avoid practices that may be detrimental to flotation. Such practices include the indiscriminate use of water, particularly that containing a wetting' agent, for dust suppression. In addition, clay stemming in wet conditions may produce slimes which could adsorb on coal surfaces, while the use of oils and greases as well as the application of stone dust and chlorides in roadway consolidation may influence adversely fine coal beneficiation.This paper deals with the application of flotation to samples of fine coal from the Bulli, Greta, and Victoria Tunnel seams. In addition a discussion is given of the mineralogical constitution, size analysis, and degree of liberation of ash constituents of the various samples.COAL SAMPLESRepresentative samples of coal from the Bulli, Greta, and Victoria Tunnel seams were obtained for testing.

Jan 1, 1961

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By M. Potesser

One of the main targets in the automotive mass industry and supplying industry is the weight reduction of the vehicle for decrease of the fuel consumption. For that reason combinations of different kinds of materials and connections of, for example, steel and aluminium are developed or are already successfully field-tested. A determining factor concerning the quality assessment of the welded joint during hybrid welding is the characterization of the intermetallic Fe-Al layer regarding strength, hardness, morphology and mainly the different phases in which Fe occurs together with the Aluminum (FeAl, Fe2Al5, FeAl3.). A combination of conventional light microscopy, SEM - EDX - analysis, the usage of an atomic force microscope including a Nanoindenter and theoretical thermodynamic calculations turned out to be highly effective. Based on the attained results, the constitution of the intermetallic FeAl layer, influenced by silicon, manganese and zinc, can be predicted.

Jan 1, 2006

By D. H. Horswill

The Red Dog Mine is the world’s largest zinc mine. It is located 145 km (90 miles) north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called the Northwest Alaskan Native Association (NANA) Development Corp. NANA acquired surface and subsurface title to this resource as part of its settlement lands under the Alaska Native Claims Settlement Act. In 1982, NANA entered into a lease agreement with Cominco. Cominco is an international mining company focused on zinc. It built and operates the Red Dog Mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language and traditions are as important to the NANA people today as they were in the past.

Jan 1, 2000

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001

"In an environment of rising energy prices and mining at greater depths, cost-efficient loading and hauling equipment is essential. Conducted at an underground mining operation, this study analyzes the energy consumption and gas emissions of diesel and electric load-haul-dump machines (LHDs) with similar bucket capacities. Based on energy prices from the first quarter of 2014, results of discrete event simulation show that energy costs for diesel and electric LHDs are US$0.24/t and US$0.07/t, respectively. Also, diesel LHDs emit 2.68 kg CO2 per litre of diesel fuel, whereas using electric machines reduces the need for ventilation to mitigate engine heat and emissions and reduces energy costs.RÉSUMÉ Dans un contexte de croissance des prix de l’énergie et d’exploitation minière à des profondeurs de plus en plus grandes, il est essentiel d’avoir des équipements de chargement et de transport les plus rentables possible. La présente étude, effectuée dans une mine souterraine, analyse la consommation énergétique et les émissions de gaz de chargeuses-navettes (LHD) au diésel et à l’électricité ayant des capacités de godet similaires. En se basant sur les prix courants de l’énergie, les résultats d’une simulation d’événements discrets montrent que les coûts énergétiques pour les LHD au diésel et à l’électricité sont respectivement de 0,24 $US/t et de 0,07 $US/t. De plus, les LHD au diésel émettent 2,68 kg CO2 par litre de combustible diésel alors que les machines utilisant l’électricité réduisent le besoin de ventilation pour atténuer la chaleur des moteurs et les émissions en plus de réduire les coûts énergétiques."

Jan 1, 2015

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By P. R. Moyer

"INTRODUCTION The Federal Explosives Act (55 Stat., 863), as amended, was passed by Congress on December 26, 1941, and became effective immediately; it amended the Act of October 6, 1917 (4o Stat., 385). The purpose of the Act was to regulate the manufacture, storage, use, and possession of explosives in order to prevent sabotage and to assure that explosives and ingredients would not fall into unauthorized hands. Under the provisions of the Act, the Director of the Bureau of Mines was authorized to administer its provisions under the supervisions of the Secretary of the Interior.EXPLOSIVES-CONTROL DIVISIONTo administer the Act, necessary personnel were employed in accordance with the appropriation made from a special presidential fund and later by Congress, and the Explosives Control Division was organized as a part of the Health and Safety Branch of the Bureau of Mines constituting the fourth division of that branch. A central office was established in Washington, D. C., and field offices were designated largely at the offices of the Health and Safety Branch throughout the country, and 50 explosives investigators were employed and assigned to work from these offices under the direction of the district engineers of the eight districts into which the United States is divided by the Health and Safety Branch. The territory assigned to each investigator was based on the approximate amount of explosives stored in that area; however, smaller territories were assigned to investigators stationed near the Pacific coast, which was indicated as critical by the armed forces."

Mar 1, 1947

By Yang Jun, Qu Mei, Zheng Yao-wu, Chi Li-yuan

Due to the necessity of the prediction of blasting seismic effect around strip mine bench blasting area, the paper provides a method to predict the blasting seismic effect by employing the superposition of seed waveform at different monitoring points. The method assumes that blasting vibration waveform per hole is similar to seed waveform at monitoring point. Therefore seismic wave consists of the superposition of the waves from all of blast holes. Firstly, via sensors multiple seed waveforms can be achieved at different distances from signature hole. Then, by using the given dose and the distance, the vibration waveform of a certain blast hole can be calculated by the corresponding seed waveforms. Finally, the initiation delay time interval per hole is added to the propagation time to the predicting point. The predictive waveform at the whole blasting area can be obtained by superimposing all of the single waveforms. Considering the vibration waveform of a single blast hole changes greatly with the distance, under different distances condition the seed wave employed to superimpose is achieved from the similar distance. The experiments demonstrate that based on the method the predictive vibration waveform and spectrum are basically consistent with monitoring results around near-field blast. Compared with single seed wave method, the superposition method of multiple seed wave is more reliable to predict the duration of blasting vibration, the peak particle velocity, dominant frequency and frequency distribution.

Jan 1, 2015