Search Documents

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

By J. C. Johnson

Underhand mining with cemented mill tailings for backfill has proven to be a safe and effective alternative to conventional overhand mining for rockburst prone mines. The ability of the cemented sandfill to survive a rockburst shock wave without failing has been observed at mines in the Coeur d?Alene Mining District many times in the last twenty years. To better understand the dynamic loading of this commonly used support material the National Institute for Occupational Safety and Health (NIOSH) performed laboratory experiments using a split Hopkinson Pressure Bar (SHPB) to quantify the maximum stress and energy absorption of cemented mill tailings from the Galena mine. Cylindrically shaped cemented backfill specimens aged 28 days were placed in the split Hopkinson pressure bar testing apparatus and a dynamic load was applied. The measured peak dynamic compressive strength of the cemented sandfill was 10.6 MPa (1540 psi) and is approximately twice the static unconfined compressive strength (UCS) of 5.5 MPa (800 psi). These test data showed about 95% of the initial energy was reflected away from the backfill and only 5% of the energy was absorbed. This may help to explain why backfilled stopes could withstand seismic events up to 3.5 Richter magnitude (Ml). When a compressive rockburst wave impacts a stope a large amount of the stress and energy is reflected away. The reflected wave is a tensile wave which creates tensile cracks and spalling in the entire wall of the stope. The backfill supports the damaged wall rock and holds it in place. Some of the stress and energy of the rockburst is transmitted into the backfill and because the backfill is being dynamically loaded it has a strength that is twice its static value and absorbs a substantial amount of rockburst energy. Although mining in deep underground mines is an extremely hazardous occupation, the use of underhand mining with cemented backfill for static and dynamic ground control increases the safety of the workers.

May 1, 2007

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By M. Lu, E. Broch

Abstract: The formation and mechanism of rock cavern roof arches are studied and effects of rockbolts reinforcement are evaluated. It is concluded that a self-supported roof arch may be formed by the excavation. To stabilize such a roof arch, fully grouted rockbolts are effective. Tensioned cable anchors may have a negative influence on the arch stability. Zusammenfassung: Die Formation und der Mechanismus von Deckenbögen in Bergkavernen wird studiert und der Effekt von Verstärkung mit Bergbolzen wird bewertet. Es wird festgestellt, dass die Exkavation einen selbst-stützenden / freitragenden Deckenbogen formen kann. Eingegossene Bergbolzen sind effektiv um einen solchen Deckenbogen zu stabilisieren. Spannkabel können unter Umständen eine negative Einwirkung auf die Stabilität des Bogens haben. Résumé: Le mécanisme et la formation de voûtes dans les cavernes rocheures sont étudiés et l'effet du renforcement par boulonnage est évalué. Nous arrivons à la conclusion qu'une voûte autosupportêe peut être formée par excavation. Des boulons entièrement scellés par coulis de bêton s'avèrent efficaces pour stabiliser de telles voûtes. Les tirants d'ancrage peuvent quant à eux nuire à la stabilité de la voûte.

Jan 1, 2003

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By V. Arslan

The primary advantage of using oxalic acid is in the formation during leaching of soluble complexes that are both photo-chemically and microbiologically degradable. In this study, chemical leaching and bioleaching methods were used for quartz sand. Using the ANOVA-Yates test technique, the effects of solids rate, temperature and oxalic acid rate were investigated using chemical leaching experiments. Solids rate and temperature were effective parameters on the chemical leaching. After the tests, the removal of Fe2O3 increased to 97.02%. Finally, the iron content decreased from 0.315% Fe2O3 to 0.0094% Fe2O3 in the leached quartz sand. The effect of pulp density was investigated on the bioleaching experiments. The bioleaching of iron oxides by Aspergillus niger resulted in removal of 47.70% of the total iron in the quartz sand, and suggested that this strain has not a good ability to remove iron impurities from quartz sand in comparison with chemical leaching. The iron content decreased from 0.315% Fe2O3 to 0.164% Fe2O3 in the bioleached quartz sand.

Jan 1, 2009

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

By Paul N. Freeman

This paper describes the in-situ performance of two IFS powered support installations at Betws and Penallta Collieries in the South Wales Coalfield, United Kingdom. Intensive monitoring of all powered support functions, strata movement, support/strata interaction and coal seam disturbance permitted an extensive evaluation of powered support performance for all periods of the mining cycle. The influence of support design, support rating, face design, proximate strata and scam section upon support and operating performance are discussed. In-situ performance is compared to design specification and to the requirements of Production Instruction 1982/6. Aspects which show significant variation are highlighted. Particular attention is drawn to the precise analysis of support/strata interaction in the form of canopy and base loading profiles. This illustrates the influence of support rating and configuration in determining the interaction of the canopy and base with the proximate strata. Extensometric monitoring of the coalface highlights the potential zones of disturbance within the seam which allied with support position monitoring provides an accurate basis for theoretical considerations of support loading. Conclusions are drawn, the application of which may enhance the performance and operation of IFS supports in thin to medium sections.

Jan 1, 1992

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By D Craw

The Rise and Shine Shear Zone is a mineralised low angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. Rocks from the shear zone obtained from recent drillholes are unweathered and facilitate paragenetic studies. There is a progression of mineral deposition from semiductile foliation-parallel shearing, to subsequent folding, and brittle fracturing. Sheared rocks are dominated by microshears containing fine grained hydrothermal muscovite and rutile that has recrystallised from metamorphic muscovite and titanite respectively. Euhedral pyrite occurs within segregations in the schist and is locally brecciated by the shears.   Arsenopyrite occurs within microshears and is intergrown with hyrothermal muscovite. Fractures within relatively undeformed schist are filled with ankerite, siderite, chalcopyrite, sphalerite and galena and these veinlets also crosscut the microshears. Locally the schist is folded and zones of brecciation, silicification and vein deposition overprint the rock. Vein quartz and albite predominate and arsenopyrite and gold infill breccia matrix and crosscutting veinlets. Sulphide deposition began in the later stages of metamorphism with pyrite deposited in quartz-albite segregations. Subsequent shearing caused brecciation of some grains and accompanied deposition of arsenopyrite ¦ gold and rare sulphides along foliation-parallel microshears. Minor amounts of chalcopyrite, sphalerite and galena were then remobilised in ankerite veins that crosscut the shears. In areas of high strain, arsenopyrite was then deposited as euhedral grains in veins and breccias. Synmineralisation deformation caused the brecciation of some grains and gold was deposited infilling fractures in the arsenopyrite. The paragenetic sequence shows gold mineralisation occurred in two distinct sets of structures (semiductile and brittle) that formed at different times in the formation of the shear zone.

Jan 1, 2006

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

Fresh coal refuse was sampled at 21 US mines. Five of the sites were drilled, sampled and tested more extensively. Field tests included Standard Penetration tests, and in-situ density determinations. Laboratory testing included specific gravity, gradation, maximum, and minimum density tests, as well as 9-inch) drained triaxial tests, 9 and 10-inch, permeability tests, slake-durability tests, and accelerated slaking tests. Some refuse sites had significantly lower shear strengths and permeabilities in old, slaked or weathered material than in fresh refuse. Testing did not show useful correlations between strength and permeability changes and other material properties which could serve as "predictors". Testing of refuse under "accelerated slaking" conditions showed promise as a comparative tool and as a potential means of preparing artificially aged samples for evaluations of long-term behavior. The state-of-the-art in slaking research, and the implications of slaking on coal refuse disposal, and on practical methods of managing slaking, were also studied.

Jan 1, 1981

By D C. McPhail, S L. Rogers, J Brugger

Using iron- and sulfur-oxidising bacteria to catalyse the breakdown of sulfides that host the gold is an important biological method for the pretreatment of refractory gold ores. Following this biological treatment a combination of chemical and physical methods are used for leaching (such as the cyanide process) and concentration (such as carbon-in-pulp or electrowinning) of gold. Although these methods are well accepted by industry, they harbour limitations in the processing of low-grade refractory ores, and regulatory agency/public acceptance of cyanide use. Thus, it is beneficial to industry to develop environmentally friendly, cost-efficient leaching and concentration techniques that are based on micro-organisms. This may soon be possible by adapting the results of recent regolith geoscience research, which has shown that micro- organisms are capable of driving a biogeochemical cycle of gold dispersion, transport and reconcentration in the supergene environment. The indigenous microbiota in biologically active soil microcosms from a number of Australian sites are capable of solubilising up to 80 wt per cent of the gold contained in these materials during 50 days of incubation. Studies using molecular microbial techniques have shown that a metallophilic bacterium, Ralstonia metallidurans, is present in biofilms on gold grains from a number of Australian sites. R metallidurans is capable of actively accumulating gold from solution, suggesting that the bacterium may contribute to the formation of secondary gold grains and nuggets. Identifying the biochemical and physiological pathways that lead to the dispersion and accumulation of gold in regolith, and quantifying the reaction kinetics of these processes may thus lead to the development of industrial bio-processing capacities for gold-containing ores.

Jan 1, 2007

By Guomin Jiang

Potassium ferrate is an excellent multifunctional reagent for wastewater treatment, but its preparation is crucial. The improved hypochlorite oxidation method was used to prepare potassium ferrate in this study. Iron nitrate, the preferred iron source, was added into hypochlorite solution and then the stabilization agent was added during the purification process of product. The influence of available chlorine content, iron molecular proportion, reaction temperature and reaction time on potassium ferrate preparation was investigated. The optimal condition for potassium ferrate preparation is 15% of available chlorine content , 0.6 of iron molecular proportion , 30i of reaction temperature , 45min of reaction time. The yield of potassium ferrate is about 67% with high purity (> 99%). The structure and performances of the product was characterized by XRD, EDX, SEM, TG and IR and the results show that the prepared product is consistent with the properties of potassium ferrate(VI).

Jan 1, 2010

A well known rock mass classification system has been altered slightly to address the issues found under remnant mining conditions. By detail study of the expected fracture patterns and local geology, the rock mass is classified to indicate the condition of the hanging wall prior to mining. The risk level of each mining step is evaluated by calculating input parameters for computer simulations from the actual rock mass condition. Seismic activity is catered for by the understanding that large event rates and large magnitude events reduce the quality of the local rock mass and that the rock mass stiffness should be adapted accordingly. A case study is presented to test parts of the protocol. Un système connu de classification des masses rocheuses a été légèrement modifié pour faire face aux questions posées par les conditions d’extraction de débris. Une étude détaillée des diagrammes de fragmentation et de la géologie locale permet de classer la masse rocheuse pour indiquer la condition du toit avant l’extraction. Le niveau de risque de chaque étape minière est évalué en calculant les paramètres d’entrée pour simulation par ordinateur à partir de la condition réelle de la masse rocheuse. L’activité sismique est prise en compte avec la réalisation que les taux de larges évènements et les évènements de large magnitude réduisent la qualité de la masse rocheuse locale et que la raideur de la masse rocheuse doit donc être adaptée. Une étude de cas est présentée pour tester des sections du protocole. Ein sehr bekanntes Gesteinsmassenklassifikationssystem wurde abgeändert um die Probleme zu behandeln die unter Restabbaukonditionen angetroffen werden. Durch detaillierstes Studium der der zu erwartenden Bruchmuster und der lokalen geologischen Verhältnisse wird die Gesteinsmasse in Hinblick auf die Konditionen der Flözoberseite klassifiziert. Das Risikoniveau für jeden Abbauschritt wird durch die Eingabeparameter aktuellen Gesteinsmassenkondition für die Computersimulation evaluiert. Für die Seismische Aktivitäten wird Sorge getragen durch das Verständnis, daß große Ereignisraten und Ereignisse hoher Größenklassen die Qualität der lokalen Gesteinsmasse reduzieren und daß die Gesteinsmassensteifheit entsprechend adaptiert werden sollte. Eine Fallstudie um Teile des Protokolls zu testen wird präsentiert.

Jan 1, 2003