Search Documents

By Jose Carlos D’Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano, Helio Marques Kohler

Nowadays the most important Direct Reduction - DR processes in shaft furnaces has to deal with carbon fines precipitation and DRI carburization issues. Based in a cooperative research program joining Catholic University (PUC-Rio) and SAMARCO Mining Co, a project dealing with pellets reduction and those two phenomena was established. This work analyzes kinetically the three reactions mentioned before, considering typical values for the operational variables temperature, flowrate, pressure and gas composition, parameters commonly used to control the DRI formation in the Reduction Zone - RZ of the shaft furnaces. From laboratories experimental results, the kinetic equations for those reactions were established and, using the superposition principle, generated a specific global kinetic model for the iron oxide reduction and the soot formation. Finally, using those experimental results and applying a planned statistical factorial analysis for the experiments, the numerical coefficients for each equation were calculated and the correlation factor determined for the proposed global kinetic equation.

Jan 1, 2015

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By QinGuo, Shenghui Guo, Lei Li, Jinhui Peng, Linqing Dai, Libo Zhang

The ferrous removal process after carbothermic reduction of chromite fines with microwave heating combined with leaching was investigated. Under the following conditions: Reaction temperature: 1150 , Reaction time : 40min, Semi coke ratio: 12% , the iron content of the reduction product : 13.05% . Metallization achieved was 52.7%. Reduced chromite was leached with 8% of H2SO4 and FeCl3 aqueous solution. The results show that: the recovery rate of chromium can reach 88.06%, the mass ratio of chromium to iron is 3.5:1 for leaching 30 minutes with 8% of H2SO4; the recovery rate of chromium can reach 88.91%, the mass ratio of chromium and iron is 2.56:1 for leaching 4h at room temperature with FeCl3 aqueous solution (100g/L). The leaching time of latter is longer but can realize the circulation effectively and reduce the waste liquid processing problem.1

Jan 1, 2016

By D. K. Panda

The behavior of single drops with gas evolution at the interface is of interest because this is one of the important reactions that occur in oxygen steelmaking vessels, where a large amount of iron-carbon drops are dispersed in an oxidizing slag. The carbon dissolved in these drops, reacts with the slag to form CO, which is evolved as a gaseous phase. A room- temperature model was used to study the nature of this type of reaction including the effect of various factors such as viscosity and the presence of surface active impurities. Experiments were done for reacting drops over a wide size range to observe various regimes of behavior. Large single drops were levitated in a counter current flow to produce a sufficiently long residence time to allow the study of the various stages in the reaction. The emphasis of this work was to obtain photographic evidence of a high quality to describe all possible modes of behavior, and so a lot of effort was given to developing and perfecting experimental techniques.

Jan 1, 1994

By Y. A. Chang

The objective of the present study is to evaluate and compile the relevant phase equilibria and thermodynamic data reported in the literature for the ternary system Cu-Fe-S. It is hoped that the results presented here will be useful to practising engineers and scientists in industry who are attempting to improve continually the existing processes of copper extraction and refining. At the same time, the present work will undoubtedly reveal the lack of some basic data which are important for the improvement of our existing extractive processes. Lastly, this work will also show that the development of theoretical models for the alloy phases in the Cu-Fe-S system is essential before complete consistency between the phase equilibria and the thermodynamic data can be achieved.

Jan 1, 1976

By Wenbo Luo, Kang Liu, Jilai Xue

"Coal fly-ash(CFA) from thermal power plants is rich in Al2O3, which has great potential as an alternative resource for alumina production. In this work, Alz03 contained in the coal fly-ash was extracted using an acid sintering-leaching process. This process was enhanced by aid of power ultrasound during the leaching. The recovery rate of Al2O3 was increased with ultrasound, compared with the similar process without ultrasound under the identical operation conditions. Leaching temperature can be lowered by about 10-l5°C and the processing time reduced by about 50%. The process kinetics were investigated in details for a better understanding of the fundamentals on the effects of power ultrasound. The obtained results demonstrate the potential application in reducing processing energy and increasing production rate.Introduction Coal fly ash is a typical solid waste generated from coal combustion in thermal power station. Vast amount of CF A accumulation lead to serious environmental problems such as air and water pollution, cropland occupation, radioactive contamination, etc. However, CFA is rich in Al2O3 and SiO2 content, so that it has a potential use as recourses for alumina and silica production [1]. Aluminum industry, especially in China, has made a rapid expansion in recent years accompanying with a large amount of bauxite consumption, resulting a urgent demand to develop secondary alumina resources like CF A to maintain a sustainable development of aluminum industry that faces grim challenge [2].Acid leaching is an efficient technology to use in alumina extraction from CF A. Since the particle of CF A is not naturally existed mineral but was formed in molten state at high temperature, the internal Al-O-Si bonds are so strong to separate alumina from the ash particle. Because of this reason, the direct acid leaching [3-6] operated at ambient temperature has low extraction efficiency, approximate 30% to 40%, which is attributed to self inhibition effect from CaS04 generated by reaction between CaO and H2S04 [7-8]. High pressure leaching can efficiently decompose mullite to release A12O 3 content in the fly ash particles, but this requires autoclave material having strong acid corrosion resistance, high temperature (100°C-300°C) and pressure (1.0MPa-2.SMPa) resistance while its operating security is low and its acid consumption is large [9]. Concentrated acid boil process is conducted at near acid boiling point (200 °C - 300 °C) in 4 mouth flask wrapped by electric heating jacket with high mass ratio of acid and ash to achieve high Al203 recovery rate from CFA. Its disadvantages are similar to the high pressure leaching technology except no-pressure, and also the operating solution at nearly boiling point acid may easily spill and splash with additional acid loss and potential safety hazard [10]."

Jan 1, 2014

By Zhang Yongzhu

In hydrometallurgical processes of PGMs separation and refining, differences between 1-PGMs (Ru;Rh;Pd) and h-PGMs(Os;Ir;Pt) in thermodynamics and kinetics have been observed. The successful practice in the separation and refining of PGMs in China, is mainly based on the following two kinetically extraction sequences of: (1) for the extraction of PGMs complexes in different configurations with coordination mechanism (AuCI,) -> (MCl6)2-> (MCl4 )2-> (MCI6) 3- , and the substitution rate for h-PGMs complexes with higher effective nuclear charge Z' is much more slow than that of I-PGMs. and (2) for the extraction of PGMs in different configurations with oxonium (or ion -exchange) mechanism (AuCl4)-> (MCl4)2--> (MCl6)2-> (MCl6)3- and the extraction of h-PGMs complexes with low surface charge density is more fast than that of I-PGMs complexes. In view of atomic structure theory, the similarity of atomic radii and chemical properties and difficult separation of PGMs resulted from the Lanthanide Contruction between 5th period (1-PGMs) and 6th period (h-PGMs). The differences between h-PGMs and 1-PGMs are due to the loss shielding of 4f subshells on 5d electrons for h-PGMs with higher nuclear number, which makes h-PGMs have a higher Z' (effective nuclear charge) and strong attraction for outer space electrons. As a result, h-PGMs metals and complexes are thermodynamically more stable and kinetically more inert than the corresponding 1-PGMs. The differences between h-PGMs and 1 -PGMs in aspects of elements properties, complexes, hydration, substitution and redox reactions , are discussed.

Jan 1, 1993

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

By Mikhail Mikhaylenko

Natural and technogenic sources of rare earth elements (REE) and other rare and scattered metals are remarkable for their chemical diversity. The pregnant solutions going to processing for the valuable metals have very complex compositions. Both targeted elements and competing impurities are present in the solutions in different chemical forms. Thus processing of such materials demands application of different technological tools addressing numerous specific tasks on the way to the final product. Screening work was undertaken to identify the best resins among developmental and commercial products addressing typical cases in the hydrometallurgy of scandium and REE. The cases outline typical sources of scandium and REE, such as streams of TiO2 production, extracted phosphoric acid, barren uranium solutions and others. Specially designed ion exchange resins can be effective tools.

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Huimin Zheng, Jian Yang, Chun-ling Yao

"Mercury in flue gas of coal-fired plants was concerned as another serious pollution when sulfur dioxide pollution was controlled now. The adsorbent made from fly ash by thermal precipitation sulfur to remove mercury in fuel gas from coal combustion plant, SEM, BET, TGA and other measurement methods were used to characterize the effect on surface morphology, sulfur distribution and specific surface. High temperature deposition furnace was applied to increase sulfur content in fly ash based adsorbents produced in lab. The study found that sulfur attached to the adsorbent surface, mesopore and microporous structure, increasing its sulfur content of adsorbent. Sulfur was filled in interspace as small molecule S2, S5, increased their surface area and enhanced their adsorption capacity. The specific surface area increased by thermal precipitation sulfur, and specific surface area which increased with increasing temperature.1. IntroductionThe mercury emission caused by human activity has accounted for 10%-30% of total mercury emission all over the world[11, and the emission from coal-fired power plant have a huge proportion of these emission caused by human activity. Active carbon microstructure and surface morphology play an important role in its adsorption capability, which offers the potential for controlling environmental pollutant, such as sewage, fuel gas, atmosphere and et al [2,31, because it is a material with high specific surface area that long been considered as an excellent adsorbent. At present, include activated carbon, fly ash, calcium-based sorbents and other novel adsorbents. The adsorption capacity and production cost were very important in the process of mercury removal by adsorbents, so the mercury removal has focus on developing adsorbents of highly-efficient. In particular, the waste of metallurgical from coal combustion and the others have a significant advantage about the cost, and they have the highly-efficient in mercury removal after modified to enhance their adsorption capacity, such as fly ash of coal-fired. Apart from specific surface area, element content, pore structure, and surface morphology of activated carbon have great effect on its adsorption ability. Compared to adsorbents without modification, active carbon impregnated with other elements, such as chlorine, sulfur, bromine and et al. had more excellent characteristics to remove specific pollutants."

Jan 1, 2011

By Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro, Thiago Samarão Motta

This work has as its objective to characterize ceramic bodies formulated with ornamental rock waste and two different clays to produce ceramic paver. Specimens were made by uniaxial press-molding at 20 MPa and then fired at 950 and 1050oC respectively. The determined technological properties were: plasticity, dry bulk density, linear shrinkage, water absorption and flexural rupture strength. The results showed that the type of the clay has strong influence on the properties of interest for heavy clay ceramics. The investigated waste must be incorporated in small amounts to avoid increasing in the porosity of the ceramics.

Jan 1, 2015

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By Guangliang Wu, Dong-chang Huang, Xin-bin Liu

High temperature mechanical properties of 50Cr5MoV roll steel was investigated by Gleeble 1500 thermal simulator testing machine The morphology, composition and microstructure of fracture surface were observed and analyzed by OM, SEM and EDS The results are indicative of that, there are two brittle temperature zones of 50Cr5MoV roll steel at the temperature of 600°C~950°C and 1300°C~1450°C, respectively. The section shrinkage rate is less than 60% The fracture mode changes from mixed ones dominated by intergranular to toughness transgranular one with the increase of temperature at the range of 650°C~1300°C. The fracture is along the solid--liquid phase at the range of 1300°C~ melting point It is crucial to formulate the 50Cr5MoV casting technology, to prevent the cracks and improve the quality of 50Cr5MoV roll steel.

Jan 1, 2016

By Theodore Ineich

The “BIOMOre” project aims to prove the technical feasibility of indirect in situ bioleaching of sulfide minerals contained in a deep underground deposit, by bringing together the disciplines required to make a success. The underground location in Poland was provided by project partner KGHM inside an operating copper mine. Key components of this project were the design and construction of a pilot plant, and its operation in an underground environment. This project also included a ∼250 t (100 m3) fragmented rock reactor hydraulically connected to the pilot plant. The pilot plant consisted of several tanks and pumps, a fluidised bed ferric iron generating bioreactor containing immobilised acidophilic iron oxidation biomass, and all the required instrumentation and utilities. Before the bioleaching phase could start, the rock reactor had to be flushed continuously firstly with water to remove chloride salts that are corrosive and also harmful for the bacteria used in the bioreactor, and secondly, with sulfuric acid solution to react with the carbonates present in the ore matrix. This paper summarizes the design, construction, commissioning, and operation of the pilot plant.

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016