Search Documents

By M. J. Collins, L. C. Trytten, K. R. Buban, I. M. Masters

Both pressure leaching of zinc concentrate, in an autoclave, and atmospheric leaching, in stirred tanks, have been employed in the expansion of zinc production at plants employing roast-leach-electrowin technology. These direct leaching methods result in the conversion of the sulphur in the feed to the elemental form, rather than to sulphur dioxide, decoupling zinc production from acid production. Atmospheric and pressure leaching methods are also readily implemented over a wide range of production rates. In choosing the best technology for expansion, capital and operating costs, zinc recovery, byproduct quality and the compatibility of recycle streams with the existing refinery must be compared. Leach testwork with several zinc concentrates using both methods has been performed by Dynatec. Recent results are presented, along with a discussion of their implications for process selection.

Jan 1, 2000

By Mingming Zhang

This paper describes the aluminum electrowinning in a batch recirculation cell system using 1-hexyl-3-methylimidazolium chloride and aluminum chloride (ionic liquids) as electrolyte at low temperatures. The technique proposed to deposit aluminum from ionic liquid electrolyte was a three-component electrolytic cell system. Ionic liquid electrolyte was circulated between electrolytic cell and electrolyte reservoir by ceramic piston pump. Two different anodes were used in the electrowinning and it was found the extruded carbon anode had better electrochemical stability and reusability. The cell performance variables studied were the current density and current efficiency as a function of aluminum ion concentration, electrolyte flow rate and applied cell voltage during batch recirculation operation. Results indicated that the current density was directly proportional to the applied cell voltage, initial electrolyte concentration and electrolyte flow rate. Under batch recirculation operation at applied voltage of 3.5 V and temperature of 80-90°C, 80-90% current efficiency of cathodic aluminum deposition can be achieved when flow rate is 20mL/min and initial concentration is 10 mol/L.

Jan 1, 2006

By Roberto Parra

The selective reduction smelting of Cu2O in Cu2O-FeOx-SiO2 melts has been studied at laboratory level, using as a feed a dead roasted calcine from a copper concentrate. The purpose of the study was to evaluate the kinetic and mechanisms of the indirect reduction with CO and the direct reduction with graphite from 1260°C to 1350°C. The reduction rate by CO was found to be 10-2 to 10-1 mole Cu2O m-2s-1. The graphite reduction macrokinetics for FeO and. Fe2O3 containing melts, was found to be a first order reaction with respect to the Cu2O concentration, with a kinetic constant of 104 to 10-3 s-1. The reduction rate was not sensitive to temperature nor to stirring, in the range studied. The measured reduction rate is almost one order of magnitude larger than the observed rate for the direct reduction of FeO.

Jan 1, 1999

By Suzzann Nordwick

Over the past decade, significant advances have been made in the development of sulfate-reducing bacteria (SRB) technology to treat acid mine drainage (AMD). Bench-scale testing, field demonstrations, and engineered applications of SRBs for the treatment of AMD will be presented. Designs include an in situ bioreactor installed in the subsurface workings of the Lilly Orphan Boy Mine in 1994, the SRB bioreactors installed at the Calliope Mine from 1998 to 2001, the integrated biological reactors built at the Surething Mine in 2001, and the ongoing development of a replaceable cartridge system. SRB technology benefits include the reduction of dissolved metal ions to insoluble metal sulfides and the neutralization of the AMD resulting from the production of bicarbonate from the oxidation of organic nutrients. This paper will address engineering design criteria including the selection of organic media and system permeability and complete mitigation of AMD. Research was funded under Interagency Agreement No. DW899388-70-01-1 between the US EPA and the US DOE and was conducted by MSE Technology Applications, Inc., through the National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405) at the Western Environmental Technology Office located in Butte, Montana.

Jan 1, 2003

By P. S. Seryogin

R & D works supported by industrial-scale tests, which were carried out by joint efforts of the OAO Gipronickel Institute and MMC ?Kola? engineers, have accomplished with the production of 90?95% metallized nickel powder in tube furnaces (NPTF), with its ?active fraction? (AF) to be further used for decopperization of nickel electrolyte by cementation. Consistently positive results obtained in the course of the lab and industrial experiments have allowed the Severonickel Combine management to effectively replace all activated nickel powder (ANP), which was then employed for cementation, with the AF, having activity over 80%, and eventually shut down the entire operation of gaseous reduction. Ever since the developed technology has been implemented, its annual economic effect exceeds 2 ml. dollars.

Jan 1, 2006

By David Hughes

The paper covers the utilization of on-line analysis in process control of solvent extraction in nickel leach solvent extraction processes in Finland and Australia and in copper heap-leach and solvent extraction in Chile. The goals of and requirements for controlling the solvent extraction stages of the processes are reviewed. The applications at three plants are compared. The development of the technology used is reviewed and design considerations are discussed. Requirements for on-line control and analyzer performance are compared. A new generation of analyzers and its effect on the set-up process of a project is introduced.

Jan 1, 2003

By Jaeheon Lee

Gold-copper alloys are shown to form during the cementation of gold on copper in a solution containing 0.25M [S2O32-] at 25oC. The alloy composition is strongly dependent on the initial Cu:Au ratio in solution and ranges from Au3Cu to AuCu3. XPS results for Au, Cu, S, and O are reported as a function of depth through an entire deposited film with an initial solution containing 20 ppm [Au] and 30 ppm [Cu]. The deposit contained about 20 atomic % gold and was predominantly Cu3Au. Underpotential deposition (UPD) theory is discussed as a mechanism for explaining the formation of these alloys. Several other systems that produce alloys during contact reduction/cementation are also discussed.

Jan 1, 2003

By O. Morfín

The most probable source of Pb contamination in the perennial reach of Aravaipa Creek, Arizona, has been determined using Pb isotope ratios and total metals analyses of samples collected from the ephemeral and perennial reaches and mine wastes located in the Aravaipa Mining District . Previously, elevated levels of Pb, Cd and As in fish in the perennial reach of Aravaipa Creek, a protected wilderness area,, were assumed to be due to off-site transport from abandoned flotation tailings piles located at Klondyke, Arizona upstream of the wilderness area.Our work replaces this inference with isotopic data that allows us to confirm this hypothesis. The Pb/Zn deposits of the district were mined between the late 1890s and the late1960s, with the most significant ore production coming from one deposit in a rhyolite dike swarm on the Western front of the Santa Teresa Mountains, a granitic pluton of Cretaceous-Tertiary age (~65 ma). Mineralogy has been well constrained across the length of the lode system: Pb and Zn sulfides predominate in the NW sector, and a mixed suite of hypogene/supergene Pb sulfide and Pb oxide minerals comprises the majority of its SE corner. Total metals analyses and comparison of metals ratios serve to constrain the source and transport of certain metals within different parts of the system. Pb isotope ratios in samples, obtained by ICP-MS analysis, define two distinct contributors. The first end-member (208Pb/204Pb = 38.513 to 38.721 and 207Pb/204Pb= 15.550 to 15.598) is characteristic of the mixed, oxide/sulfide ores at the SE end of the deposit. A second end-member (208Pb/204Pb = 38.855 to 38.946 and 207Pb/204Pb = 15.610 to 15.625) characterizes samples taken from the NW, purely Pb sulfide end of the lode. Pb isotope ratios from perennial reach sediments are closely correlated with ratios given by samples from the Klondyke tailings site and by Pb sulfide samples from the NW sector, the primary source of ores processed at Klondyke.

Jan 1, 2003

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008

By Zhang Qin

Dolomite is main impurity mineral in phosphate ores. In practice of phosphate ores production, the grade of concentrates is only containing P2O5 31-32%.In this study, even the increasing of floatation reagent consumption and decreasing of floatation recovery, economic performance is estimated high according to the decreasing of H2SO4 consumption in subsequent production of phosphate fertilizer and the increasing of products value. In floatation stage, influence factor include the synergism impacts of floatation collector, the stages, time, concentration of ore pulp, which were discussed respectively in this paper. Raw material is characterized by mineralogy, chemical analysis, the grain size analysis and milling test . The results show that the grade of concentration can reach to P2O5 36% by deeply de-magnesium oxide from phosphate ores by floatation , which yield a high added value.

Jan 1, 2009

By P. Aguirre

Recovery of zinc, copper and nickel from electroplating waste solutions was achieved 'by using a Pulsated Percolated Porous Electrode "3PE" reactor on a pilot plant scale. Intensity - potential curves were used to study the possibility of metal removal and to define the working potential range. The present study describes the use of the 3PE reactors in several electroplating industrial units for the decontamination of their effluents. These effluents were issued from different industrial solutions such as cyanide, sulfate, chloride and Watts baths. Using the stripping curves, deposition rates and electrical efficiencies were determined as function of the metal concentrations in these effluents. Their decontamination could be achieved to the level of few ppm of metals with reasonable current efficiencies. The recovery rates of zinc and copper were about 93 and 99 %, respectively. The. treated effluents contained less than 7 and 1 % of the initial contents of Zn and Cu, respec¬tively. This process allows the recycling of the recovered metals and leads to water saving.

Feb 13, 2014

By Jan G. H. du Preez, C. Viviers, B. J. A. M. van Brecht, H. E. Rohwer, Nicole M. Sumter

"At the basis of metal ion separation lies some particularly metal ion specific chemical property which lends itself towards exploitation. This could be in the form of an anionic complex or a neutral chelate complex. In the former a cationic centre with a particularly high affinity for the complex will have to be designed. In the latter case a stereospecific chelate ligand containing the correct symmetry and type of donor atoms will have to be designed. In both above cases the ""active centre"" can be entered in a from that it can function in different media of hydrophobicity, eg a precipitant, a resin or a solvent extractant. Recent results obtained in this laboratory will be used to illustrate how the above variables can be exploited to develop improved processes for the separation of base metal and platinum group metals.IntroductionThe separation of metal ions in hydrometallurgy can be performed broadly speaking with two major aims. Firstly the separation/removal of a certain group of metal ions, either as a means of preconcentration or as a removal from effluent as part of a purification process and, secondly the removal of a specific metal ion from an industrial stream in order to produce a specific metal in a pure form. This latter operation is by far the most difficult of the two and is becoming more so in the light of the fact that the world is moving in the direction of lower grade ores and increasing pollution. Such a process can be divided into three essential parts, firstly the molecular one in which an active centre is required to obtain specificity, secondly a matrix within which this active centre must function, i.e. as part of a resin or solvent extractant and thirdly the design of the total system to optimize the realization of the operation."

Jan 1, 1996

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By T. K. Mukcherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover(1) base metals. such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By B. R. Adams

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and' surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By W. G. Davenport

A survey of world copper refining tankhouse .practices has been carried out. This paper compiles the results and examines changes in operating practices .since the similar 1987, 1991 and 1995 surveys. Continuing trends are the installation of ISA Process and Kidd Process stainless steel cathode technology, polymer concrete cells, anode preparation machines and automatic cranes. Instrumentation and automatic control are increasing, particularly for addition agent optimization; solvent extraction .and ion exchange techniques are being increasingly applied for electrolyte purification. The overall consequences of these changes have been 'improved cathode purities and enhanced tankhouse productivities.

Jan 1, 1999

By Toshihiko Emi

The quest for cleaner steel is driven by increasingly stringent requirements from the manufacturing and construction industries. Key issues are the occurrence and removal of inclusions; These are discussed in the context of the unit processes of deoxidation, refining, transfer and casting of molten steel. Process thermodynamics and kinetics are also discussed. Recent progresses achieved and problems yet to be solved are elaborated, and an integration of the unit processes into a system to produce extra clean, steels with better performance is presented.

Jan 1, 1999

By René Bustamante

The subject of this paper is a comparative evaluation of different copper smelting gas cooling techniques, using "productivity and quality" criteria. The first section presents a brief description of the operation of the radiant and the evaporative cooling systems, focusing on the differences between each other, in particular regarding. a) mass and energy balances; b) gas flow, temperature and composition; c) dust concentration and recovery. This section includes a brief discussion of the "client-server chain", i.e. the links between the cooling equipment and the down-and up-stream operations. More in particular, the up-stream server relationship impacts on the operating stability of the furnace, and in turn on furnace down-time and Cu production losses; and the down-stream client relationship affects the operation of the electrostatic precipitators, in terms of workload and cost of handling larger quantities of dust of a given dust size The second section deals with the development of indexes to measure and compare value added through the "utilization, productivity and quality" that can be expected of both cooling methods at the physical and economic levels, and the impact on the overall smelter productivity and the final cost composition of copper. The final section presents the results and includes a discussion of the comparative advantages and disadvantages of both cooling systems.

Jan 1, 1999