Search Documents

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil. One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester. Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e .? in flash combustion mode. The velocity. temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data. this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Lv Guozhi, Niu Liping, Shi Guanyong, Liu Yan, He Jicheng, Du Yanjun, Dou Zhihe

"We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The alloy prepared in different process conditions was characterized via XRD, SEM, OM and TEM and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that there are three distinct regions: copper-rich regions, chromium-rich regions and the inclusion regions. Inclusions are mainly in the form of stomata and Alz03 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Adding Na3AlF6 and heating agent can effectively reduce the inclusion content in the alloy.1 IntroductionIn recent years, with the development ofhigh power vacuum and high-pressure technology ,the CuCr alloy contact material which has many advantages gradually replaced the traditional W-Cu and Cu-Bi series alloy contact material, and become the first choice of material in high-voltage and high-power vacuum switch contacts['-3l. The traditional powder metallurgy method, infiltration method and vacuum arc melting method[4-SJ are using metal Cu powder and Cr powder as raw material by casting molding, and have disadvantages such as high production costs, complicated process, poor product density and low yield, especially in the large size alloy ingots[9-12l. At present, the world regards CuCr alloy new preparation technologies as the first place, and how to achieve a large size the CuCr alloy ingot preparation has become a hot research of CuCr alloy[3l. Zhang Ting-an and Dou Zhihe[l-3l who are supported by national natural science fundation of china successfully successful developed new technologies and core equipment to prepare large-size copper-chromium alloy through aluminum thermal reduction-secondary refining method, and obtained two national invention patents. The method includes two key steps: one is get CuCr alloy consumable ingot by Thermit-SHS with electromagnetic stirring, the other is to refme the CuCr alloy ingot to remove the pores, inclusions and other defects by electroslag remelting technology to get dense and uniform CuCr contact material. The preliminary study results show that means of electromagnetic stirring evidently inhibit effect of alloy ingot macrosegregation during the electromagnetic casting stage, but there are still microstructure defects such as alumina inclusions and pores in the alloy ingots. Therefore, Zhang Ting-an et al refer new ideas of using the electroslag remelting to refine Cu Cr alloy ingots and effectively remove the defects of the ingots such as pores and inclusions [3l _ At present, there is no report of study on the electroslag remelting refining processes of CuCr alloy (the refining slag, remelting current). This article will research mode of occurrence and distribution law of inclusions in the large-size CuCr alloy ingots by Al Thermit-SHS under magnetic field stirring action and provide a theoretical basis for chosing refining slag to remove inclusions by electroslag refining. Meanwhile the article analyses the effect of reduction conditions of Thermit-SHS on the types of inclusions, mode of occurrence and distribution of regular inclusions in alloy ingot, and refer theory for inclusions regulation in the large-size alloy ingots."

Jan 1, 2013

By James R. Craig

The slags generated during gasification of petroleum coke are heterogeneous and con-sist of many different phases. These phases are important because their physical properties affect the operability of gasifiers and because they concentrate many elements that are present in the petroleum coke feed in only minor to trace quantities. An understanding of the chemistry and physical nature of these slag phases is necessary to predict behavior in the gasifier and in considering the ultimate use or disposal of the materials. Slags typically consist of silicate glasses, calcium-silicates, free iron-nickel metallic phases, iron sulfides, and aluminum oxide spinels enriched in iron, chromium, and vanadium. The partitioning of elements among these phases has been analyzed and will be discussed.

Jan 1, 1989

By Daniel S. Gwinner

The tolling, or processing for a fixed fee, of aluminum drosses to recover the metal units is a common practice in the Aluminum Industry. The Dross Toller is acting for the owner, and since most dross processes result in material going to landfill, it is important for the owner of the dross to insure that the toiler is processing the material and handling waste disposal in an environmentally responsible manner. The paper discusses the Dross Toiler Audit Program, first from the Reynolds Metals Company perspective. Included are the reasons the company deems it necessary to audit and a description of the items covered during the audit. Finally, there will be a discussion of the audit from the Tollers perspective - what the Toiler can expect when the auditor arrives.

Jan 1, 1995

By Pedro Morales

At present the Codelco´s smelter & refinery business have growing complexities, concentrates with lower copper grades, higher impurities contents, and environmental restrictions which have lead to refocus the Codelco business, not only by considering the isolated developments for each of the Codelco´s Smelt & Ref complexes, but also as an integrated corporative complex scheme which improve the economy of scale, optimize the synergies, and include new technologies for higher productivity and lower operational costs. Accordingly, for the 2008-2012 period, Codelco have prepared a Development Plan integrated to the smelters and refineries business units that improve its single potentialities of and include the advances for the Teniente Converter [1] and Continuous Converting [2] Technologies, and also include the concept of uncoupling the smelting process from the converting process allowing a higher operational flexibility, and a better control of its contaminants. Thus, processing the white metal generated in the Teniente Converter unit of the smelter A into the smelter B has comparative advantages. These changes in the business concept allow an overall increment of the smelting capacity by processing only white metal as a final product through a very marginal investment in this way the total or partial conversion of the white metal into blister copper is eliminated allowing to use the available gas capture-treating capacity, and available acid plants for increase smelting capacity as well.

Jan 1, 2006

By Chuan-fu Zhang

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. XRD pattern of precursor precipitated at pH=9.0 is different from that of ß-CoC2O4?2H2O precipitated at pH=1.0 which indicates that the precursor powders are one type of cobalt complex. According to the results of element analysis and IR spectra, it can be inferred that the composition of the precursor is [Co(NH3)x]C2O4?H2O(x=1.2?..6) formed by the coordination reaction at pH=9.00 in the Co(II)-C2O42--NH3-NH4+-H2O system. It?s found that the fibrous cobalt powders greatly inherited the morphologies of the precursors. Many factors could affect the formation of the fibrous cobalt precursor powders, such as the initial Co2+concentration, pH value and so on. The SEM images show how they influence the morphologies of the precursor powders. By adding proper surfactant, the dispersion of the precursor powders would be improved. At last, the final product-fibrous cobalt powders which are about 0.3~0.5min size and 40~60 in aspect ratio were produced by thermal decomposition of fibrous cobalt complex at 400~500°C in the weak reducing atmosphere.

Jan 1, 2006

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By G. Richards

The Trail smelter of Teck Metals Ltd. produces about 90,000 tonnes of lead per year through two stages of refining following KIVCETTM smelting. Bullion from the KIVCET furnace is first treated in a pyro-refining plant in preparation for Betts electrorefining which makes 99.99% pure lead. Pyro-refining consists of number of integrated unit operations to remove primarily copper, arsenic, antimony and tin. The operation of this plant to meet the specifications for electrorefining requires attention to bullion management and selective use of reagents. The processes used for pyro-refining are reviewed in terms of chemistry and control.

By J. M. Casas

This work presents the development of an ionic equilibrium model and its use to simulate the distribution and concentration of chemical species (speciation) in sulfuric acid - cupric sulfate solutions in the 0-2 pH range, 0.1-10 gpl copper concentration range and 15-45°C temperature range. The model consists of a set of equations which represent the equilibrium relationships for the ionic reactions and the mass balances for the components present in the system. The effect of ionic strength was taken into account by correcting the equilibrium constant in concentrated solutions. Several species can be formed at different pH and temperature values, the principal being: HSO-4, SO42-, CuSO4(aq), Cu2+, and H+ in order of increasing solution acidity. Simulations show that concentrations are highly dependent on pH. The sulfuric acid speciates mainly as bisulfate ion (HS0-4) and hydrogen ion (H+) at pH values lower than 1. The model presented in this work can be applied to predict and analyze the solution composition in electrolytic copper processes such as electrowinning, electrorefining and electrodialysis, as well as the purification of various industrial solutions.

Jan 1, 1999

By Kuniaki Murase

Cadmium telluride (CdTe) semiconductor has been well investigated as a CdS/CdTe heterojunction solar cell material since its band gap is suitable for energy conversion from sunlight into electricity. In this paper a new electrochemical processing of thin-layered CdTe using basic aqueous electrolytes is reviewed from the standpoint of thermodynamics using a potential-pH diagram. The cathodic electrodeposition of the stoichiometric CdTe with a flat surface morphology took place at more positive potentials than that of the Nernst potential for the bulk-Cd deposition and at more negative potentials than that for the hulk-To. In this potential region deviation from the stoichiometric composition of eleetrodeposited CdTe was controllable by the Cd(II)/Te(IV) concentration ratio, pH, or concentration of complexing agent for Cd2+ ions of the electrolytes, The deposition behaviors for ammoniacal media were well accounted for by the potential-pH diagram of the Cd-Te-NH3-H2O system devised by a combination of those of the Cd-NH3-H20 and the Te-H2O systems, Diagrams for other complexing agents, ethylenediamine and diethylenetriamine, were also constructed to investigate and discuss the electrodeposition conditions regarding the corresponding media.

Jan 1, 2003

By E. Gutierrez-Miravete

A computational method for the simulation of mold filling processes is described. The method is based on the representation of the flowing or deforming medium as a collection of mutually interacting parcels of material. Instantaneous positions of individual material parcels are calculated by numerical integration of the dynamic equations, subject to appropriate initial and boundary conditions. So far, the method has been used to produce qualitative simulations of some flowing and deforming systems encountered in mold filling technology, and our findings are summarized herein. In all cases, individual material particle motions can be followed in detail, allowing critical examination of potentially problematic mold design features.

Jan 1, 1992

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By Xuewei Lv

An intelligent recognition and quantification system for the micrographs iron ore sinter was developed in the current paper. The average distribution parameters in a gray histogram of minerals by a Gaussian gray distribution model were obtained. The feature curves of the gray histogram of two minerals were achieved by combining the two density functions. The feature indexes, such as the number and position of the peaks and the valleys of two minerals in different ratios, were quantified by differentiating the distribution functions. This algorithm is able to extract the feature of the minerals adequately and accurately for recognizing the composition and phases of the minerals intelligently.

Jan 1, 2009

By V. Yahorava

Mintek has developed a non-destructive Resin-in-Leach method for the recovery of Rare Earth Elements (REE) from phosphogypsum (PG) waste dumps. However, PG from different sources was found to be highly variable in terms of REE recovery and physical properties. Development of a pre-treatment process was initiated to improve the robustness of the current REE recovery process in order to render it effective for any type of PG. Extensive research into the mineralogy of REE associations with PG revealed that the majority of REE are trapped inside phosphogypsum clusters which inhibits their recovery. Hydrothermal treatment of PG-containing slurry was found to result in re-crystallisation of gypsum with the release of REE phases encapsulated in it. This process was tested on various PG samples and subsequent REE recoveries improved from 5 to 80%. This approach carries a large potential for unlocking value associated with gypsum dumps worldwide.

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Wen-Ming Chien, Vamsi Krishna Kamisetty, Amrita Mishra, Ivan Gantan, Prathyusha Mekala, Dhanesh Chandra

"The phase equilibrium and characterization studies by using high temperature X-ray diffraction (XRD) and differential scanning calorimetric (DSC) methods have been performed for binary organic thermal energy storage materials. The organic thermal energy storage materials undergo a solid-solid state phase transition before melting which stores large amounts of thermal energy. Two materials [tris(hydroxymethyl)aminomethane(TRIS) and 2-Amino-2-methyl-l, 3- propanediol(AMPL)] were used for this study. Binary samples of AMPL-TRIS were prepared to perform high temperature XRD characterization and DSC studies and the binary AMPL-TRIS phase diagram was developed. The high temperature solid-state phases of AMPL and TRIS were characterized as a disordered BCC structure. It was found there is virtually no solubility of TRIS in AMPL or vice versa below -75 °C. The maximum solubility of TRIS in AMPL is 11% TRIS at 75 °C. The eutectoid transformation was shown at 19%TRIS-81%AMPL composition and at a temperature of 75°C. Lattice expansion calculations on single phase of TRIS and AMPL have been performed.IntroductionThermal energy storage materials can store a large amount of heat due to the presence of thermal transitions from the orientationally ordered to disordered phases occurring before melting. These molecules (such as amine and alcohol derivatives of neopentane) can reorient as a whole about the central carbon atom to form orientationally disordered crystals (ODIC) and their spherical shape makes them reorient relatively easier. Thermal energy storage materials are becoming increasingly important as a renewable energy resource. These molecules undergo large changes in enthalpies at solid-solid transitions. The presence of these compounds with large enthalpy changes are identified as potential thermal energy materials and some of die applications are solar cell systems [1-3]. Binary mixtures have been found as a way to adjust the transition properties in addition to pure compounds [4]. Tris(hydroxyrnethyl)aminomethane (TRIS, C(CH2OH)3NH2) and AMPL, CH3C(CH2OH)2NH2) are two important thermal energy storage materials."

Jan 1, 2012

By Farzaneh Sadri

After water leaching of an acid baked REE concentrate, impurities such as Fe, Al, Th, and Cu are removed by neutralization with different reagents such as NaOH, Mg(OH)2, MgCO3, CaO, and CaCO3. Among these chemicals, lime (CaO) and limestone (CaCO3) are the preferred reagents due to their low costs. However, because of calcium sulfate dihydrate (gypsum) precipitation, they are not so common in industry. One of the disadvantages of gypsum precipitation is the adsorption of REE to the precipitates, losing a fraction of REE to gypsum which is hard to recover. In this paper, batch and continuous conditions in the impurity removal process using limestone are investigated and the differences between these two processes are examined. Based on the experiments, REE uptake by gypsum significantly increases in continuous processes, and different gypsum morphologies are observed.

By Neale R. Neelameggham

"Ferrous and non-ferrous metal industries are used to handling several billion tons a year of ore bodies, fuel and fluxing agents by mineral processing techniques and varieties of extractive metallurgy ""Reduction"" processes. Metal industry know-how can be applied to meet the challenge of Reducing CO2 in the atmosphere. Processes for generating alloys of carbon and hydrogen by Reducing the CO2 and water mixture, [carbonated water or water vapor] called Soda, to easily stored fuels are normally endothermic. The processes are similar to generation of hydrogen alone from water which is also endothermic. But hydrogen is more difficult to store than compounds [or alloys] of carbon and hydrogen. This recycling of CO2 and water are possible by using other forms of energy by innovative carbon capture methods.Thermodynamic Diagrams developed for Soda [CO2 and H2O] - metal reactions provide hints for using low cost unused stored energy in un-recycled metallic waste for thermal conversion. Choices for conditions for the electrochemical approaches [using solar - wind - hydropower] are also discussed.INTRODUCTIONIn 2006, I was reading some of the arguments put forth by learned scientists on the benefits and lack of benefits of bio-fuels. I found that the arguments rose partly from the differing system boundaries that were chosen by one versus the other. Some part of the argument may have been based on political climate or atmosphere rather than the analytical science. This situation is seen when scientists discuss which came first - the chicken or the egg, the fuel or biological matter, the oxide or the element, and so on.Then I thought –[just like many of the learned persons participating in this symposium] that common fuels - regardless of them being simple hydrocarbons or oxygenated hydrocarbons or carbohydrates - can all be made from the respective oxides of carbon and hydrogen by simple chemical reductions efficiently carried out in an economical fashion. This is the systematic approach we take when designing a chemical or metallurgical process facility."

Jan 1, 2008