Search Documents

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Y. Maeda

Kosaka Smelter is a copper smelter located at the nothern part of Japan? and has been treating. complex sulfide concentrates using flash smelting technology for a long time. The flash smelting technology has an advantage in the point of controllability of matte grade and heat balance in the reaction shaft. But the disadvantage of this process, is that the dust generation ratio is high compared with other smelting process such as injection smelting technology. This reason why is that the flash smelting process is the oxidation process for the fine sulfide concentrates applying flash reaction in the oxygen enriched stream In addition of this disadvantage, the sulfide concentrates contains much volatile impurities is resulted the dust; eneration ratio more. This paper outlines the recent improvement of the flash reaction in the furnace and the behavior of impurities in Kosaka Smelter.

Jan 1, 1998

By Jorge Alberto Soares Tenório, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Franco Alves Lavacchini Ramunno

"The traditional process for recovery of metals from waste electric and electronic equipment (WEEE) usually involves pyrometallurgical processing. However, the application of this technology to processing waste printed circuit boards (WPCBs) might lead to the formation of dioxins and furans, due to thermal degradation of flame-retardants and polymeric resins present in the board substrate. Therefore, this paper proposes a hydrometallurgical route for the recovery of copper. The acid leaching behavior of copper has been investigated at three different temperatures (25°C, 50°C and 75°C) with and without the addition of an oxidizing agent (hydrogen peroxide - H202). The dissolution kinetics for acid copper leaching was calculated based on chemical analysis by ICP-OES (Inductively Coupled Plasma - Optical Emission Spectroscopy). At 50°C with 1 mol/L H2S04 added 10 mL H202 (30%) each half hour under pulp density of 1 g I 10 mL, 100% of copper was extracted after 3 hours. The dissolution kinetics of copper with H2SO4-H2O 2 followed 1 - (1 - X)113 =Ket, i.e. chemically controlled reaction model.IntroductionThe information regarding the generation of waste electric and electronic equipment (WEEE) are still difficult to obtain because the estimates should take into consideration the historical production and sale of various products and the rate at which they reach the end of their life cycle, whose duration depends on the behavior of consumers [1]. Thus, the estimated overall WEEE generation varies between 25 and 50 million tons each year, which corresponds to more than 5% of all municipal waste generated [2], and this amount will increase at a rate of 3 to 5% per year, approximately three times faster than other individual types of waste [3].Printed circuit boards (PCBs) are essential parts of electric and electronic equipment (EEE), being found in virtually all electronic products, as well as in weapons systems [4]. A PCB is a basic component, which consists of a board where copper tracks are deposited. While the board behaves as an electrical insulator, the tracks connect electrically the various components attached to the board [ 5]. In addition to glass fibers, paper and resins, the PCBs contain significant amounts of metals, such as copper, iron, nickel, lead, stain, silver, gold and palladium [6]. In general, the weight fraction of metal is around 28% and the remainder of the boards is composed of plastic (19%), bromine (as flame retardant - 4%) and ceramic material (49%) [7]."

Jan 1, 2014

The effect of change in slag composition upon metal losses to the slag and the relationship between slag composition and slag matte separation was investigated at 1400°C. The synthetic slags containing CaO, MgO, SiO2,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Precious Group Metals) from the Merensky Reef of South Africa. The matte with a grade of 9.3% Cu and 16.0% Ni was a typical electric furnace product. The results indicated that the Cu and Ni solubility in the slag increases with the increase of the basicity ratio and CaO and MgO contents of the slag. At constant CaO/MgO ratios the rise in basicity decreases the metal losses. When FeO and SiO2 contents of the slag are kept constant, the substitution of MgO with CaO decreases the metal losses. The relationship between slag composition and matte-slag separation was found to depend primarily on the basicity ratio and the FeO content of the slag. The net effect comes from a strong interaction of the two in such a way that increasing basicity and decreasing FeO contents deteriorate the clean separation of the two phases.

Jan 1, 1994

By Patrick R. Taylor

Ilmenite concentrate and methane are fed to a non-transferred arc thermal plasma reactor to produce a powder that is primarily TiC and Fe. This material has promising characteristics for powder metallurgy applications. Free energy minimization plots were used to predict the feasibility of the reaction. An estimate of the optimum molar ratio between the ilmenite concentrate and methane was made based on the mineral composition. Argon-helium mixtures were used as plasma gases. The effects of power input level, carrier gas flow rate, powder feeding rate, and methane-ilmenite molar ratio were studied and the behavior of the system characterized. Two different powder injection angles were tried. A mathematical model to describe the temperature profiles in the reactor was formulated and solved. The product has been characterized by x-ray diffraction and atomic absorption. A conversion of 97 % of Ti to TiC was achieved. It was found that minor amounts of titanium oxides, iron carbide and free carbon are also present. TEM and SEM were used to study the morphology.

Jan 1, 1996

By L. I. Rosato

A novel hydrometallurgical process for the recovery of silver and gold from neutral leach residue that is based upon leaching with thiourea, is described. Laboratory and pilot plant studies have shown that 80-90% of the silver and 60-70% of the gold can be recovered by:? ( i) leaching zinc calcine with 'Spent electrolyte at pH 2.0-3.0 to generate a precious metal-bearing zinc ferrite residue, (ii) leaching of the thickened zinc ferrite with 3-5 g/L thiourea in a six stage carbon-in-pulp circuit, (iii) elution of silver and gold from the loaded carbon with a thiourea- butanol solution, (iv) thermal regeneration of the stripped carbon and (v) recovery of the precious metals from the pregnant eluate by cementation with zinc dust. The reasons for adopting the thiourea CIP leach and the preferred operating parameters for each process step are presented. The requirements for the destruction of any thiourea transferred to the zinc circuit are outlined, and the results of an integrated one tonne/day pilot plant operation at Canadian Electrolytic Zinc are given.

Jan 1, 1990

By Wei Gao, Qing-cai Liu, Cun-fang Lu, Jian Yang, Hinmi Zheng

"The mode of occurrence of sulfur and mercury in 57 Chinese bituminous coals have been examined using X-ray fluorescence spectrometry (XRF), X-ray diffraction (XRD), and Zeeman atomic absorption mercury spectrometer. Mercury levels in coal are related to the geographic location of the coals and types of the coals. A synthesis of result indicated that most likely occurrence modes of mercury in high-sulfur and high-mercury coals are in solid solution in pyrite. Our study from 57 coal samples showed that most values of mercury concentration in coal varied from 100 to 1000 ng/g with an average of approximately 500ng/g, and mathematical model about correlation between mercury and sulfur was gained by mathematical statistics. This is apparent that mercury and sulfur vary concomitantly from coal data (table 3) , the high correlation between them in all coals at confidence of 95% ( a=0.05 ) .1. INTRODUCTIONThere contained about one trillion ton abundant coal resources in China. As a leading level of proven coal reserves in the world, the coals mainly distributed in north China and northwest China, especially in Shanxi, Guizhou, Shanxi provinces and Inner-Mongolia autonomous region. At the same time, China has the largest production and consumption of coal, and has the output of coal nearly accounted for 37 percent of the world's production. Coal-fired power plants are the major source of energy generation in China, and the proportion of coal combustion is up to 75 percent in the total energy configuration. Therefore, the mercury pollution caused by coal-fired has become a topic of wide-spread discussions since 1990. The contamination of mercury of human activities accounted for 10 to 30 percent [1], and the mercury emissions of coal-fired flue gas has made the greatest contribution to the pollution of atmosphere[2] In the past 30 years, the global increasing concentration of mercury pollutant in atmosphere maybe result from coal combustion[2]. The mercury emissions caused by coal-burning has become the main reason of China's mercury pollution, and the characteristics of mercury pollution is closely related to China's energy configuration, additionally, the features of mercury pollution have changed from the point pollution in 1970's to diffused pollution today[3]. Mercury can be found in various types of coals, and it is evaporated into gas phase during the combustion process."

Jan 1, 2011

By Hu Long

In this, the first systematic study of the oxidation of orpiment (As2S3) in sulfuric acid solution under oxygen pressure at temperatures above 170°C, the effects of retention time, temperature, particle size, oxygen partial pressure, the concentration of sulfuric acid and pulp density were evaluated. The effects of cupric and ferric ions on the oxidation rate of As(III) to As(V) were also examined. The products of oxidation are As(III), As(V), SO42- and elemental sulfur. At temperatures ranging from 170 to 230°C, most of the arsenic was found to be in the trivalent state, and oxidation to As(V) with oxygen was very slow. This was confirmed by attempting to oxidize a synthetic arsenious solution. However, the rate of oxidation of As(III) to As(V) is rapid in the presence of ferric ion. Elemental sulfur was found at all temperatures investigated, which can be further oxidized to sulfate at high temperature.

Jan 1, 1999

By P. Henry

A novel electrochemical cell has been developed for the recovery of MnO2 from residue of pyrolusite ore leading loaded with Fe, Al Ni, Co and Si impurities, This new process can be considered as an alternative to the traditional methods : S02, H2O2 or bioleaching. It has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. Electrochemical characterization and kinetic studies have shown that MnO2 is effectively leached by electrogenerated ferrous ions at high current density from a pulp containing less than 5 g8 Fe. The chemical reactions are : Cathode (inox) : 2F23+ + 2e ? 2 Fe2+ Bulk: MnO2 + 2 fe2+ 4H+ ? Mn2+ + 2 Fe3+ + 2 H2O Anode (Pb-Ag) : H2O ? ½ O2 + 2H+ + 2e Global: MnO2 +2H+ Fe2+ = Mn2+ + H2O + 1/2 O2 The catholyte (MnO2 pulp) circulates upward in the expanded mesh cathode separated from the sulfuric acid solution anolyte by a separator which shows high mechanical resistance, low porosity, low potential drop, and reasonable cost. Laboratory and mini-pilot tests have led to the construction of an OT crating pilot plant (100 kg/hr) able to leach more than 95% of Mn, Ni, Co at 1000-1200 A/m2, 50°C with high faradic yield (> 95 %) and low power consumption (3.2 kWh/kg kWh/kg &4D). New applications like the treatment of spent Zn-Mn batteries, polluted soils, spent catalysts and oxide ore (cobalt, nickel) with electrogenerated redox species are now investigated at a laboratory and mini-pilot scale.

Jan 1, 2000

By V. A. Luganov

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°C and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 550 DC with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilitc. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By Drew Sinha

Success of the environmentally benign semiconductor manufacturing depends on the cost-effective integration of the principles of reduce, recover, reuse and recycle from source material to final product disposal. Increasing demand combined with current shortage of polysilicon provided unique opportunities to recover the silicon waste, caused by various defects, in wafer manufacturing process. Current practices relating to recovery and reuse of waste silicon produced, from crystal growth process to finally polished and epitaxially deposited silicon wafer, at Mitsubishi Silicon America is presented. Future plan to recycle the process generated silicon fines produced during the intermediate steps of the wafer manufacturing process such as grinding, slicing, lapping and polishing is also discussed.

Jan 1, 1998

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By J. P. Evans

The modem 'copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system 'can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By J. L. Watson

The composite nature of titanomagnetites found on the west coast of the north island of New Zealand is an important parameter in the beneficiation of the black beach sands for export to Japan. To investigate this composite nature, borehole and plant samples from the Waipipi Ironsands Ltd property were subjected to a series of separations in heated Clerici solutions at densities varying from 3.2 to 4.6 g/cc. The resulting density fractons were analyzed magnetically and a set of distribution curves for composite grains proposed. In addition the experi¬mental data was plotted to produce titanomagnetite sand 'washability curves" which illustrate the possible problem areas in beneficiation that may arise due to composite titanomagnetite grains. From this data a set of guidelines are suggested for interpreting the curves in terms of ease of gravity concentration. The composite nature or liberation of titanomagnetite grains is shown to favor high and low grade composites with few intermediate compositions being isolated. The relationships between grain size, borehole depth and liberation are examined and related to beneficiation procedures for the black sand deposit.

Jan 1, 1982

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single- stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-SiO2. The special studies have been conducted in the Gintsvetrnet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting. as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By Yan Beygelzimer, Alexander Spuskanyuk, Victor Varyukhin

"A cellular model of the plastic deformation of polycrystalline aggregate is proposed and comprehensively described. Representative volume element (RVE) of a solid body, that is being deformed, is described as a population of interconnected units that, in turn, can consist of lower scale level units. Sliding along the various allowed sliding systems deforms simple units, which do not have an internal structure. For consideration of stress distribution within the limits of components, the approach of self-consistent field is used. Rotation of units and moment stresses connected with it are taken into account. Results of computer experiments are analyzed.1. IntroductionMicromechanical models of polycrystals are a link between the research of plastic deformation on micro and macro levels. Computer simulation of inelastic strain of polycrystals has found a great deal of interest as well. Despite the fact that this approach does not allow to obtain macroscopic constitutive relationships that are used in deformed solid body mechanics, it clarifies essential features of the phenomena in many aspects. First of all, it concerns effects stipulated by interdependence of micro-level and macro level of plastic deformation processes. Also, with the computing mechanics, instead of constitutive relationships, the adequate computer models can be used. Broad possibilities for computer simulation of various processes are opened by cellular automata approach. By means of numerical experiments, the cellular automata allows to study the macro behavior of the whole ensemble of cells depending on the local microscopic laws that define evolution of each cell and its interaction with the closest environment.We propose a mathematical model of a polycrystalline aggregate (the cellular model) based on a self-consistent scheme and on the interaction law similar to the one by Berveiller and Zaoui [1]. Our original solution is the self-similar structure of cellular automata that allows modeling of the fractal nature of real materials (Figure 1). The goals of this work are to present the major structures and relations of cellular model of polycrystal and to test this model for its adequacy as for describing known effects and dependencies. Identification of the model and its application for studying of concrete polycrystals are put aside for the future research."

Jan 1, 2001