Search Documents

By David W. Evans

"Induced hydraulic fracture of strata during roof bolt installation is a potentially prevalent, but masked phenomenon within the underground coal industry. Previously reported resin testing programs (McTyer et al., 2014) examined the relationship between resin mixing effectiveness and varying bore hole diameter. The methodology employed within this earlier test program facilitated a further critical area of research – the measurement of back pressures generated within the bore hole during standard rock bolt installation practices. Experimental data has indicated that fluid resin can be pressurised to levels where it exceeds the compressive strength of the strata, inducing hydraulic fracture within the immediate area of the bolting horizon. The routine cycle of roof bolting serves to propagate this effect, progressively fracturing and delaminating the roof during mine advancement. This masked phenomenon can lead to a perception of difficult ground conditions - mining efficiencies and costs are therefore affected, with increased needs for additional support subsequently required to restabilise the inadvertently damaged roof.Further analysis of the parameters associated with resin bolt installation has now been conducted, assisting in the development of an empirical relationship between bore hole pressure, bore hole diameter and bolt insertion times. This relationship has been analysed for 15:1 ratio resins and 2:1 ratioresins, within 28mm and 30mm boreholes. Further to this, load transfer performance has been comparatively assessed for both 28mm and 30mm boreholes, suggesting that for 2:1 resins, acceptable resin mixing and load transfer can be obtained within a 30mm bore hole. The combination of 2:1 resins, utilised within a 30mm bore hole, may well provide the optimal solution to reduce the risk of hydraulic fracture in weaker strata during resin bolt installation.INTRODUCTIONA growing number of industry papers have previously investigated areas of concern associated with the performance of cartridge style resins in roof bolting, predominantly focussing on the effects of plastic film gloving, inadequate resin mixing and the pressurisation of resin within the bore hole. These three effects have a critical influence on the load transfer of the steel bolt element, through the cured resin and into the surrounding strata.Gloving occurs due to the plastic film of the resin cartridge partially encasing or wrapping around the steel roof bolt element – a known phenomenon over many years (Pettibone, 1987). The plastic film creates regions of discontinuity between the bolt, cured resin and borehole, reducing effective load transfer into the strata. Experimentation conducted into the effects of bolt ends fully encased by plastic film (Pastars and MacGregor, 2005) revealed that load transfer can be reduced by 85 to 90% in worstcase occurrences. It is also known that the aggregate filler size used within the resin can assist in shredding and breaking up the plastic film – this effect was observed in a previous study on resin mixing effectiveness (McTyer et al., 2014)."

Jan 1, 2015

By Raj R. Kallu

Underground gold mines in Nevada are typically hosted in geologic zones with a wide range of geotechnical properties ranging from blocky competent rock to faulted and highly altered soil-like material. Geotechnical engineering design in weak rock utilizes rock mass classification systems as inputs to both empirical and numerical methods. The most common rock mass classification system utilized in the gold mines of Nevada is the easy-to-use Rock Mass Rating (RMR) system; however, in practice it is difficult to apply in weak to very weak rock masses. This paper attempts to improve the sensitivity of RMR in weak rock masses by utilizing W-RMR?a modified procedure for calculating RMR?and evaluates its performance against other methods of determining RMR for predicting in situ moduli. In-situ rock mass moduli were determined using a portable plate loading device (PPLD), and these data were used to quantify the improved sensitivity of the modified RMR versus existing classification systems. The PPLD was designed for performing rapid and economical in-situ deformability tests in a mining environment. Tests were performed at eight sites yielding thirteen rock mass moduli measurements. Statistical analyses indicate Detailed-Discontinuity RMR-89 and W-RMR provide the best correlations to the in-situ moduli compared to other methods of calculating RMR.

Jan 1, 2014

By Dennis R. Dolinar

Roof falls, even of supported roof, still constitute a major hazard in underground mines. However, associated with any fall or instability is a pattern of roof movement. Therefore, the National Institute for Occupational Safety and Health, Pittsburgh Research Center, has been conducting research into the development of practical extensometer systems that can be used to measure this displacement and to determine if a roof fall may occur, thus increasing miner safety. For extensometers to be used in the detection of potential roof falls in coal mines, an understanding of the movement and displacement rates that will lead to roof failure is required. Because roof falls are unpredictable, it is often very difficult to obtain this information. Therefore, in a coal mine in the lower Kittanning seam in Pennsylvania, a room widening experiment was conducted to intentionally cause a roof fall while roof movement data was collected. In this experiment, two adjacent rooms 5.5 m (18 ft) wide supported with 1.5 m (5 ft) resin-grouted bolts and instrumented with extensometers were widened to 9 m (30 ft). In one of the rooms, 3.6 m (12 ft) cable bolts were installed as supplemental support. In the room with no additional support, a roof fall occurred 72 h after the room was widened. Much of the 3 cm (1.2 in) of movement in this room resulted from the instantaneous and transient response to mining with displacement rates up to 7.6 cm/d (3 in/d) being measured. This was followed by a steady state displacement phase with a rate of 0.43 cm/d (0.17 in/d). Just 12 h before the fall, movement deeper in the roof caused the rate to accelerate to 1.1 cm/d (0.44 in/d). The roof in the room with the supplemental cable support did not fall even though the total roof deformation was over 7.6 cm (3 in). Significant roof movements and strains in the cabled room were detected to a depth of 3 m (10 ft) while maximum cable loads were over 180 kN (40,000 lbf). Essentially, the roof was in postfailure with the cables maintaining the material, while roof stability was indicated by a steady state displacement rate of only 0.025 cm/d (0.01 in/d) at the end of the test.

Jan 1, 1997

By Stephen C. Tadolini, Anand Bhagwat

"Intrinsic supports installed in mines with limited seam or mining heights have always proven to be difficult when the required support length is longer. To date, three solutions have been used to ensure that the correct length bolt is installed to achieve the required anchorage or to maintain immediate roof material: combination bolts, milled-notch bolts, and hot-notch bolts. The combination bolts use threaded sections and couples, which can be screwed together to form the required length. The primary bolt of choice, to minimize costs and achieve the desired support, has been milled- or hot-notch rebar bolts. These notches can be placed at strategic (required) locations along the bolt axis, so the bolt can be successfully bent and straightened during the installation process. However, these notches can reduce the strength of the bolting system; special reductions are detailed in ASTM F432-13 (2013). Technical advances in steel rolling and forged heading processes have led to the development of a deformed rebar bolt termed, the BORE bolt, which stands for Bendable Oval REbar. The BORE bolt can be bent at any location and straightened during the bolt installation cycle. This support exceeds the minimum designed capacities described in ASTM F432-13 and meets the yield and tensile strength requirements of a full diameter no. 6 rebar bolt. The profile and shape also reduces the resin annulus during the installation process to enhance mixing and shreds the cartridge film to help eliminate glove fingering.INTRODUCTIONThe height or depth of competent strata material, in the immediate mine roof, can be greater than the developed mine openings heights. This is especially true in coal mine openings where 50% of the minable seams in the US are less than 50 inches (132 cm). When this scenario occurs, it can be difficult to insert steel bolts in a solid single length. Figure 1 illustrates what difficulties can be experienced when a roof bolter operator is working and supporting a thin seam coal mine. There are three viable options currently available. Lengths of the bolt can be threaded and a steel coupler can be used between the sections to reach the required depth of anchorage. These systems, called “coupled bolts,” usually require a larger diameter hole to facilitate the larger coupler diameter and can be anchored with an expansion shell, resin, or a combination of both. To ensure that the coupler will develop the tensile capacity of the bolting system, required by ASTM 432-13 Standard Specifications for Roof and Rock Bolts and Accessories (2013), the threaded bars should be completely rotated and engaged into the coupler. Premature failures can occur when the threads “strip out” if not inserted completely."

Jan 1, 2018

By S. J. Jung

The goal of this research is to demonstrate how optimization methodology can be coupled with the finite element method for greater stability of underground mine openings. As a result of increasing mining depth and intersection of geologic discontinuities, mining environments are becoming more complex. Current design procedures are rapidly becoming inadequate. In this research, the finite element method has been coupled with optimization criteria to design more stable and safe underground openings

Jan 1, 1993

By Dale A. Didcoct

Through the combined efforts of the C. S. Bureau of Mines, the coal industry, and Burrell Construction and Supply Company, New Kensington, PA, a steel fiber reinforced concrete crib block to improve coal mine safety in the area of roof control has been developed and is currently in use commercially. The development objective was to improve health and safety conditions with a stiffer, stronger, nonflammable roof support at a competitive cost. During the time this method of roof control has been in use in the mining industry, it has proven to be both functionally and economically effective.

Jan 1, 1982

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By Thomas Lautsch

After a short description of geology and gateroad roof support technology in the German coalfields the development of roof bolting as primary roof support is presented. Based on geotechnical parameters, different strategies used for roof support at depths of 3,300-4,600 ft. are explained. Strict quality management and a strict monitoring program are part of the entry development. A number of recently finished developments are described such as the introduction of standardized bolts and accelerated resin systems. An outlook of future goals is presented. The paper concludes with a comparison of roof control systems at RAG's mines in the US and Germany.

Jan 1, 2000

By Syd S. Peng

A total of 209 cases of subsidence data over longwall panels in 16 US coal seems have been collected and built into a subsidence database. The database is developed under MS Windows environment. It uses a very user-friendly menu driven system. The empirical formulae for a number of commonly used subsidence parameters have been derived from those collected subsidence data.

Jan 1, 1995

By Khaled Morsy

Longwall mining is one of the most widely practiced underground coal mining method. The behavior of the longwall gob is very critical in the understanding of the complex ground response to longwall mining. In the limited data available, the values of gob moduli used in numerical modeling ranged from 1,000 psi to over 300,000 psi. Such a wide variation in moduli would greatly affect the results of the numerical analysis. A better understanding of the behavior of the gob will allow numerical models to be more accurate for simulating longwall mining conditions. In this study, a gob model based on the Terzaghi's model was incorporated into the comprehensive finite element package, ABAQUS, to simulate the loading behavior of longwali gob material. A case study was used to verify the proposed gob model.

Jan 1, 2002

By Herryal Z. Anwar

In recent years, many both mining and civil engineering projects are developed in the area which may be categorized unstable, such as fractured and jointed rocks or "water sensitive rocks". For example, in underground coal mining, in which the floor strata normally consist of weak shale, the problem that may arise in roadway is floor heaving. In this case cement injection in borehole appears to be an economically effective method in order to make roadway more stable. This method may be also applied in the projects in which the constructions are laid on fractured and jointed rock. Nevertheless, the successful cement injection is much dependent on the water-cement ratio and the injection technique. This paper discusses the application of cement grouting to improve the ground stability in longwall mining, the laboratory experimentation of cement grouting and the method of floor injection.

Jan 1, 2000

By Brian Clifford

A wide range of different cablebolt systems are available and in use in hard rock and coal mines around the world. The birdcaged cablebolt was initially used in UK coal mines in conjunction with rockbolts in the late 1980's. More recently other cablebolt configurations have been used. Innovations in cablebolt design in the UK have been driven by a demand to find a system as effective as the birdcaged cable, but which can be installed more rapidly and offer immediate support. A laboratory short encapsulation pull test (LSEPT) has been developed for both rockbolt and tendon systems which measures bond strength and stiffness in rock and assesses the full range of potential failure modes. This test is now used along with conventional 'gun barrel' and shear tests to provide full assessment of bolt and tendon performance. This test may be incorporated into a new performance based British Standard for rockbolts and long tendon systems. This paper describes the performance of some of these systems as being applied to UK and South African coal mines.

Jan 1, 2001

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Chris T. Franke

The Waste Isolation Pilot Plant is a deep underground facility mined in bedded salt interspersed with persistent clay inter- beds. The clay seams delineate beams of salt above and below the excavations which strongly influence excavation performance. This paper reviews available rock mechanics information relevant to improving drift stability by removing the roof beam. Conceptual deformation mechanisms, relevant field data, and numerical analyses were used to investigate the effects of mining the roof of the excavations along a clay seam. Finally, a case study that applies the results of this investigation is presented.

Jan 1, 1997

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999