Search Documents

By F. L. Wilke, J. Fabian, D. Oravec

The task of production planning in ore mining is primarily con¬cerned with the removal of ore blocks within planning periods spread over the life of the mining operation. The investigation of this problem in the past resulted in the introduction of computer based optimizing techniques for production scheduling and se¬quencing. Although these techniques succeed in computing an "optimal" mine output for one planning period, they usually fail in composing a practical and feasible mine plan over the periods in concern. This paper describes conventional production planning based on operations research and the capabilities of a knowledge-based approach. An example of a planning system for the Slovak under¬ground iron ore mine Nizna Slana will be presented. By combina¬tion of these two techniques this system should improve the qual¬ity of planning procedures.

Jan 1, 1996

By R. E. Brewer

Pilot scale flotation tests were conducted with a 1-ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pct of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated using the column. The tailings were first water leached at approximately 600 C, and the water-leached tailings, which contained approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH and sodium sulfide addition on gold flotation recovery and redox potentials were examined. maximum gold recovery, 36 pct, was achieved at pH 8.5 with a sodium sulfide addition of 0.18 lb/st.

Jan 1, 1989

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By J. van der Walt

In hot deep mines the ventilation and refrigeration requirements are determined primarily by the magnitude of the various sources of heat, and where in the mine they arise. Refrigeration is expensive, and in order to ensure that it is utilized effectively and at the lowest possible operating costs it is important that careful attention be given to the selection of plant, and how the cooling is to be distributed. The paper outlines the essential features of the highly effective strategy that has evolved in recent years in cooling deep mines in South Africa.

Jan 1, 1980

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

"The seventh annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held last February at the SME Annual Conference & Expo in Phoenix, AZ. A total of 21 students entered the poster competition. The students were required to submit one-page abstracts, which were reviewed by the judges, after which they prepared posters to display their work. A panel of judges went to each student and listened as the student explained his/her research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. Recognizing the effort required to participate, the MPD provided monetary rewards to all participants. First place received $1,000; second, $500; and third through seventh, $200. All remaining entrants received $100 each. The winners have their abstracts published in this issue of Mining & Metallurgical Processing. As in past years, there were separate levels of competition for undergraduates and graduates.Now for the winners:Graduate winnersJoseph Halt won first place for research on the use of additives to starch binders to create iron ore pellets. Vivek Agarwal received second for working on using solvent extraction to concentrate lanthanum. Jordan Rutledge placed third for utilizing tannins to depress calcite in fluorite flotation. Fourth through seventh places were Vu Truong, Jacob McDonald, Hunter Sceats and Doug Schriner.Undergraduate winnersLaura Nugent won first place for using high-frame-rate cameras to follow bubbles as they moved from the pulp to the froth in flotation cells. Taylor Graham earned a second-place finish by researching how to acid leach low-grade manganese carbonate.Although its cliché to say everyone’s a winner, everyone can benefit from attending the MPD Student Poster contest. All the students were able to display their work to potential future employers, and industry professionals could talk to the up-and-coming engineers. Next year, there will be another competition for more posters and networking, so get ready to attend.Thank you to all the students for participating; Lisa Schlink for chairing the session; the judges, Aaron Noble, Debra Switzer, Mohammad Rezaee, Nick Gow and Ren Bryce, for evaluating the abstracts and posters; and the MPD sponsors for supporting the competition. This has only been successful with the input of all three groups. Engineering iron ore pellets to reduce their dustinessJ.A. Halt and S.K. KawatraGraduate student and professor and chair, respectively, Department of Chemical Engineering,Michigan Technological University, Houghton, MI, USAIntroductionIron ore pellets are hard spheres made by agglomerating iron ore concentrate and binders. Pellets are the preferred ironbearing feed for blast furnace ironmaking. Starch has been proposed as a binder because it has good adhesive properties, does not contaminate pellets and is relatively cheap. However, starch binders typically lead to weak pellets with rough surfaces, and these can cause high levels of dust within process equipment and when pellets are handled and shipped (Halt and Kawatra, 2014). Our research shows that by adding a small quantity of other additives, pellets made with starch binders become smooth and strong. The newly designed binder leads to significantly lower levels of fines when pellets are handled."

Jan 1, 2016

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By J. M. Mutmansky, B. Kolonja

A PC-based simulation model using the software packages SIMAN and CINEMA was developed to simulate and animate truck-shovel operations. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. Statistical analyses were performed, and appropriate theoretical distributions were fitted for various time events in the truck-shovel cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an optimal dispatching strategy to produce an equilibrium between the quality and quantity of production.

Jan 1, 1995

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By R. J. Sweigard, R. V. Ramani

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on final land use plans. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mines. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1987

By B. Denby, D. J. McMlarnon

During the ongoing research into the possible applications of Virtual Reality in underground operations, the AIMS Research Unit has developed a user-interface driven program which enables a user to input the geometry of underground mines, and add equipment and working processes in order to produce an accurate simulation of their operation. This paper describes the main features of this system (VR-MINE). Virtual Reality is a field which has grown out of three dimensional computer graphics techniques, and allows a user to move freely around a model held within the computer's memory. Movement around this model is carried out by the use of intuitive peripherals such as joysticks, with the user's view from their position within the model being produced in real time on a computer monitor or other device (such as a headset). This enables a user to interact with any three dimensional model and see the results of their actions immediately. VR-MINE is broken into two separate programs, both running under Microsoft Windows 3.1 or above. The first, the editor, allows the user to develop the mine layout and add equipment and personnel. The mine geometry is considered to be made up of various types of objects, for example a straight roadway segment which can be inclined, a junction roadway segment, and a turning segment. The geometry can then saved into a file to be loaded in by the second program of VR-MINE, the viewer. This generates a real- istic representation of the mine, with undulating floors and walls. It also has the ability to display multiple windows on the mine at the same time, which are arranged interactively. The simulation occurs within this program, with the user traversing the model in real time to examine possible areas of improvement in operations. This paper gives a number of examples of how the AIMS Re- search Unit has applied this technology to a range of underground mining scenarios to improve the safety of workers in the under- ground environment. The application discussed include computer graphics and Virtual Reality systems to training, risk analysis, visualisation, simulation, accident investigation and major hazard planning.

Jan 1, 1996

By R. Herrera-Urbina, D. W. Fuerstenau

A large number and a wide variety of chemical reagents are used in flotation processes for wettability and Eh control, particle agglomeration/dispersion and bubble stability. A historical account of the use of flotation reagents through the years since flotation was introduced as a viable and economic process for the concentration of sulfide minerals is given and a review of old and modern postulates of their interaction with minerals is presented. Although the results of surface and colloid chemistry studies with well characterized mineral/flotation reagent systems have advanced our understanding of the role played by these chemicals in the flotation process, many questions remain unanswered. Moreover, new flotation reagents are needed to solve the challenge posed by the treatment of problematic-type ores and fuel deposits that have increasingly become the source of our raw and energy materials. Because of the depletion of high-grade and relatively easy-to-process ores, flotation scientists and engineers are confronted with finding more specific and selective flotation chemicals to effectively and economically concentrate minerals. The development of new flotation reagents is vital for cleaning fine coal and processing polysulfide, polymetallic ores, and mixed oxide/sulfide ores.

Jan 1, 1989

By Peter J. Huck, Yoginder P. Chugh, M. Jennings

INTRODUCTION Large areas of the United States coal reserves have been undermined by room-and-pillar mining over the past century. These abandoned mines generally cause subsidence of the ground surface many decades after mining. Reports from England (1) where there is a longer history of room-and-pillar mining indicate that mines abandoned two centuries ago may still be causing subsidence, and causing surface destruction to urban areas or farm lands that have been developed in the interim. The devastation wrought by subsidence, both in terms of property loss and societal disruption is enormous. The authors discuss here the methods by which subsidence in abandoned mines may be controlled. Two distinctly different subsidence control technologies have been developed in the U.S. for abandoned coal mines. These are referred to as (1) Point Sup- port methods, and (2) Areal Backfilling. As the names imply, point support methods are used to protect individual structures, or even individual foundation elements of structures, whereas areas backfilling techniques may be applied to protect entire neighborhoods or urban districts hundreds of acres in extent. Both point support methods and areal backfilling have specific sub-categories of techniques that may be applied under different conditions as appropriate. POINT SUPPORT METHODS Point support methods are characteristically employed by civil engineers chartered with the design of a new structure or the protection of an existing structure. The subsidence control measures are only a part of a larger project, the safety of which must be assured to a degree of near certainty. The costs of point support methods involve a large number of bore-holes and the use of expensive materials in relatively small quantities. There exist several dozen point support methods, which operate either to support the underground cavities, controlling subsidence, or to isolate the structure from the effects of subsidence if it should occur. The latter methods usually involve deep foundations through the mine opening supporting the structure on the underlying strata. Our concern will be with the former method to support underground cavities to prevent subsidence. Gravel Columns and Associated Methods Gravel columns may be placed in the mine opening using the methods shown in [Figure 1]. Boreholes are drilled through the mine strata, and gravel poured down the borehole to form a pile on the mine floor. When the tip of the pile contacts the mine roof, it is rodded down to spread the pile, and permit additional gravel to be placed. The objective is to place as much gravel as possible in the mine opening, and to achieve firm contact with the mine roof. The gravel pile acts to reduce subsidence by three mechanisms. The filling of a significant fraction of the open mine volume reduces the amount of potential subsidence simply by killing open volume within the mine. In effect, the extraction ratio has been reduced by introducing the volume of gravel. The toe of the gravel pile abuts against nearby pillars, providing lateral support and protection against pillar deterioration. In effect, the height of the pillars has been slightly reduced by burying their lower portions. Finally, some direct support is provided to the roof strata, reducing the roof span and enhancing stability. The gravel column method may be used in a variety of applications, and with materials other than gravel. For example, gravel columns may be placed in a close line around the perimeter of the building to form a continuous gravel wall. The interior of the site may then be completely filled with sand, slurry or other material. Alternatively, a lean concrete may be used in place of gravel, so that the piles achieve significant structural capacity. The grout column, shown in [Figure 2], begins with the installation of a conventional gravel column which is placed around a grout pipe that extends through the borehole into the mine opening. When the gravel column is in place, portland cement grout is injected in stages. At each stage, sufficient grout is injected to fill the interstices in the gravel to build a column perhaps two meters in diameter and a meter tall. The group pipe is then raised one meter, and after the previously injected grout has set, the next stage of grout is injected. The process builds a column of grouted gravel to the

Jan 1, 1982

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By S. A. Beeson, C. Poole

This paper describes the development of a novel selective flocculation technique for recovering phosphate values from ores containing silicate or carbonate gangue minerals. Data from initial flocculation response and reagent adsorption studies on component mineral suspensions and synthetic mixtures were used to assess the influence of various process parameters (e.g., reagent dosages, particle size, solids concentration, and conditioning regimes) on single-stage selective flocculation tests involving natural silicate and carbonate ores. In these tests a high degree of selectivity was achieved using low dosages of a low-molecular-weight cationic dispersant and a mid-range molecular weight cationic flocculant. Testwork was then extended to the evaluation of several floc recovery systems (sedimentation, hydrocyclones, and floc flotation) in a multi-stage process involving redispersion and reflocculation. Results from these tests clearly demonstrated the feasibility of producing marketable phosphate concentrates from both ore types.

Jan 1, 1999

By F. J. Menzer, E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 91,000 tonnes of ore per day and has copper ore reserves estimated to be in excess of one billion tonnes. Functional groups within the Geology Department (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct exploration and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1992