Search Documents

By Milos Krofta, Donald B. Aulenbach, James P. Van Dyke

INTRODUCTION An innovative Ø.1-MGD (378.5-m3/day) biological and phyicochemical wastewater treatment system at Hancock, Massachusetts, USA, has been treating the domestic sewage generated from the four-season Jiminy Peak timeshare resort since 1985. The influent raw sewage is collected and equalized in an equalization tank, then biologically treated by two rotating biological contactors (RBC). A portion of the RBC effluent is discharged to a secondary sedimentation tank to simulate conventional waste treatment by a conventional RBC system. For parallel treatment the remaining portion of the RBC effluent is discharged to an innovative Sandfloat (SASF-8) clarifier to simulate a two-stage biological and physicochemical treatment by RBC-Sandfloat. Both secondary sedimentation effluent and Saandfloat effluent are later combined together and discharged to a tertiary sand filter and two UV disinfection'units for final polishing. The operation and performance data of Jiminy Peak plant in the period of May 1985 to March 1988 was fully documented in the Lenox Institute technical report No. LIR/Ø3-88/292 (391 pages, March 1988). This report presents only background information and complete plant data in the period of April 1988 to January 1989. Dr. Lawrence K. Wang and Mr. James P. Van Dyke have been the Consulting Engineer and Director of Special Projects, respectively, for the Jiminy Peak Project since 1985. (Key Words) Innovative and Alternative Technology, Rotating Biological Contactor, Sandfloat, Dissolved Air Flotation, Sedimentation, Tertiary Filtration, Ultraviolet, Disinfection. BACKGROUND INFORMATION Jimmy Peak, Inc., Hancock, Massachusetts, has designed and constructed a secondary wastewater treatment system consisting of preliminary/primary treatment facilities, two rotating biological contactors, a dissolved air flotation clarifier, a secondary sedimentation clarifier, a sand filter and two ultraviolet (UV) disinfection units. Total average wastewater flow is approximately Ø.1 ) (378.5 cubic meters per day). In accordance with the Consulting Engineer's preliminary design, the total wastewater stream is initially collected and equalized by an equalization tank, and then biologically treated by rotating biological contactors (RBC). Part of the RBC effluent is diverted to a Krofta Sandfloat (SASF-8) for physicochemical clarification in order to simulate an innovative RBC-Sandfloat two-stage waste treatment system. The remaining part of the RBC effluent is diverted to a sedimentation tank for secondary clarification in order to siumulate a conventional secondary RBC-sedimentation waste treatment system for the purpose of parallel comparison. Both Sandfloat effluent and sedimentation effluent are later combined together and discharged to the subsequent sand filter and UV disinfection unit for final polishing. Figure 1 shows the flow diagram of Jiminy Peak Plant. The Massachusetts Clean Waters Act (M.G.L.c.2l,s.26-53) was amended by Chapter 246 of the Acts of 1973 to authorize the Massachusetts Department of Environmental Quality Engineering (DEQE), Division of water Pollution Control, Boston, Massachusetts, to regulate discharges into all waters of the Commonwealth of Massachusetts, including groundwaters. The DEQE regulates discharges through the issuance of discharge permits which impose limitations on the amount of pollutants which may be discharged in the effluent, together with monitoring and reporting requirements and other conditions to insure adequate treatment of all liquid wastes prior to discharge. The DEQE reviewed the application submitted on behalf of Jiminy Peak, Inc. for a permit to discharge sanitary wastes from the Jiminy Peak secondary wastewater treatment system located off Brodie Mountain Road, Hancock, Massachusetts, and subsequently developed the conditions contained in the Groundwater Discharge Permit No. Ø-188. More specifically, Jiminy Peak, Inc. (i.e. the permittee) has been authorized to discharge into the ground from the Jimmy Peak secondary wastewater treatment facilities for which the Permit No. Ø-188 was issued, a treated effluent

Jan 1, 1989

By Richard H. Olson

Talc is currently mined in the U.S. in six major districts. The size and depth of the ore bodies and their mineralogy dictate the types of products manufactured and the mining and processing methods which must be employed. The geology of the major deposits is well known and will be but briefly discussed The major emphasis will be placed upon the past history of the districts, the size and depth and configurations of the ore bodies, the ore mineralogy, and how all of these factors govern the types of mining and processing operations which may be employed in each of the districts.

Jan 1, 1984

By E. Allen Wendt

It is both a great pleasure and something of a challenge for me to have this opportunity to address a gathering encompassing such a wealth of expertise in the minerals field, It is particularly challenging because I have been asked to turn your attention from the relatively glamorous subjects of gold and money to the more mundane questions of our International commodity policy and the place of buffer stocks in that policy. However, these questions may be of more immediate importance for our economic interests at home and Abroad. I can testify that the problems affecting international commodity markets and the possibility of international action To resolve those problems are matters of real concern to Washington as well as to your industries,

Jan 1, 1978

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990's to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998

By Max B. Holfeltz

[Many factors impact the selection of one mining method over another for deep seated, thick seam coat deposits. Generally if an operating mine is recovering coal at high volumes from thick seams then a truck/shovel fleet is required for coal loading. The next consideration is how to remove the associated burden. If an operation has relatively small amounts of burden associated with the coal then a truck/shovel fleet may be employed for burden removal simply to standardized the entire mine equipment concept. On the other hand large amounts of burden associated with the coal can justify employment of draglines for burden removal. Specific economic, productive, and physical factors contribute to the final decision.]

Jan 1, 1983

By Thomas R. Kuesel

In simpler times, construction was a cooperative undertaking. The frontier tradition of barn-raising is the construction equivalent of the academic ideal of a single student seated on a log with Horace Greeley. In a more complex world, ideals become more elusive. Still, it was only a generation ago that toll revenue bond financed projects generally involved a team composed of investment bankers, engineers, and construction contractors, who all shared a common objective -- to create something useful, at minimum cost and in minimum time, with fair compensation to all involved. In an increasingly contentious public climate, the team has too frequently been splintered into separate camps of owners, engineers, and contractors, who have lost the old objective of creation and have, under the guidance and control of the lawyers, substituted two new primary objectives: 1. To protect one's own skin. 2. To detect and punish culpable negligence of one of the other parties. This process has become so ludicrous that a number of thoughtful observers from all of the camps (including even some lawyers) have come to recognize that there must be a better way to undertake construction works than to use them as wrestling arenas. The road to improved contracting methods starts with mutual understanding of each other's problems and viewpoints. To this end, discussions such as this RETC session make a useful contribution. To

Jan 1, 1983

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By Robert T. DeGavre

I have been asked by the Society of Mining Engineers to present a paper on Inco Limited's Indonesian nickel project as a case study in the financing of large overseas mining projects. I welcome this opportunity It is a story worth telling not only because the project itself represents a significant human achievement but also because there are certain important lessons that can be derived from our experience in financing the project. The paper will be divided into four sections: (i) a brief history of the project, (ii) a critical appraisal of the project's financing plan in terms of the goals that we sought to achieve, (iii) some comments on certain factors underlying the relative success of the financing plan, and (iv) the contributions that the engineering staffs must make to a successful financing plan. The paper will not present a technical assessment of the project since Inco Limited has been asked to submit a series of papers on this subject at the International Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979.

Jan 1, 1978

By Wei Li

Carbothermic reduction kinetics of ilmenite concentrates catalyzed by sodium chloride and the microwaveabsorbing characteristics of the resulting reductive products were investigated; the reduction degree of the reaction was deduced to be . Results show that the activation energy is 112.03 kJ/ mol when NaCl is used as catalyst, lowering to 23.11 kJ/mol for the final stage activation energy using sodium silicate as a catalyst. There is a sharp change in the reduction rate constant at temperature ranges of 1,223 K - 1,273 K and 1,373 K - 1,423 K. Microwave-absorbing characteristics of reductive products were measured by the method of microwave cavity perturbation. It was found that microwave-absorbing characteristics of reductive products obtained at temperatures of 850° C, 1,100° C and 1,150° C show sharp changes. Through X-ray diffraction (XRD) characterization, it was found that the formation of Fe occurs at a temperature of 900° C during the reduction process of ilmenite concentrate. The decrease of FeTiO3 content results in the decrease of microwave-absorbing characteristics, while the increase of Fe content gives rise to the increase of microwaveabsorbing characteristics. The decreasing trend is larger than the increasing trend, which is the main reason for the sharp changes in the microwave-absorbing characteristics of reductive products at the temperature range of 850° C to 900° C. When the decreasing trend is smaller than the increasing trend, it becomes the main reason for the sharp changes in microwave-absorbing characteristics of reductive products at the temperature range of 1,100° C to 1,150° C. Kinetics results show that sodium chloride can catalyze the carbothermic reduction of ilmenite, and microwave-absorbing characteristic investigations indicate that microwave heating can be used in the carbothermic reduction of ilmenite.

By J. Pereyra, M. DeMarco

"INTRODUCTION It can be vital that bolted joints holding subassemblies together remain secure. Bolts should resist the loosening effects of vibrations and dynamic loads yet need to be easily removable during maintenance. When a threaded fastener is subjected to vibration, the rapid movement causes a lowering of friction against the threads and a subsequent loss of preload. The loss of preload allows the fastener to vibrate loose and possibly fall out. As the diameter of fasteners increase desired preload becomes increasingly more difficult to achieve. Input torque requirements for achieving proper bolt preload is exponentially related to any given fasteners diameter. This means that specialized tooling or bolting practices are usually required to attempt the tightening of fasteners to reach their required preload. Traditional methods can cause problems with joint integrity and do not provide consistent bolt load across the bolted surface. BOLTED CONNECTIONS A failed critical bolted joint can lead to high maintenance costs, machine downtime, and risk to worker safety. Control of the clamp load in a bolted joint is vital. However, when faced with a problem joint, it is not surprising that the design engineer will not have an answer if asked about the clamp load. Torque calculations must always be based on the existing conditions that often are vague. Unless all parameters are correct, the calculation will be unreliable. Examples of parameters are: • Thread condition of the fasteners • Hardness of contact surface • Material (steel, aluminium, copper, etc.) • Extra friction from a locking fastener • Extra friction from an adhesive • Lubricant on the thread • Type of bolt head (flanged, regular or serrated) • Surface coating of the bolt • New or reused fastener During tightening, bolts are subjected to both tensile and torsional stress. The total stress in a bolt can be calculated using the formula: Total stress = vsx2 + 3txy2 In order to maximize the desired tensile stress (sx) it is vital to minimize the torsional stress (txy). Tensile stress (clamp load) is achieved when the bolt is axially elongated. Unwanted torsional stress (twisting) in bolts arises during tightening due to thread friction. High thread friction increases torsional stress and causes yielding at lower clamp load levels than normal. A lubricant is necessary to minimize the malign torsional stress. However, many commonly used bolt-locking systems are based on increased thread friction (deformed nuts, adhesives, etc). To minimize thread friction and concurrently safely secure the joint has often incorrectly been considered impossible. The use of locking systems that increase thread friction is the single most common reason why the full capacity of bolted joints is not utilized. The following example illustrates the problem."

Jan 1, 2015

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

By S. D. Rosenthal

"This paper will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia, and the journey within academia going into the second year. INTRODUCTION As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. Mining Engineering degree in May of 1982, my first job with Utah International in the Farmington area took me back to my home state of New Mexico. Some of you will remember that the early 1980’s was not a period of prolific opportunities for mining engineers; given low commodity prices, especially for copper (for example, Anaconda Company had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton). Gold was taking off in the mid to late 1980’s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia so after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma copper purchase, Beanup and HBI) and was reviewing assets and staffing so internal opportunities became scarce. Employees were encouraged to ‘leave the company and find work elsewhere.’ So, off I go to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, Arizona, and a posting with Phelps Dodge (now Freeport McMoran). After 12+ years without living close to snow we moved to the Denver area in a new position with Newmont Mining Corporation. Along the way I became a Professional Engineer (Nevada) and completed a Masters in Project Engineering and Management. After 11 years with Newmont, I moved to Butte, Montana where I accepted a position as Assistant Professor of Mining Engineering."

Jan 1, 2015

By W. Rocher

The Minera Ojos Del Salado (?MINOSAL?) concentrator is located 20 kilometers southeast of Copiapo, Chile and processes copper ore provided by its Santos and Resguardo mines at a capacity of 4,200 tip (4,620 stpd). Phelps Dodge acquired the majority interest in MINOSAL in 1982. The principal incentive for this purchase was the exploration potential of the property. At that time, the concentrator plant was a small, antiquated installation with a capacity of 674 t/d (740 stpd). In 1982, the majority of the ore was produced from the Santos and Resguardo mines, but custom ores of copper, silver, and gold were also treated. The acquisition occurred at a crucial time in the copper business, since the price had fallen to nearly $0.50 per pound. In 1985, Phelps Dodge purchased the outstanding interest in MINOSAL and acquired 100% of the property. Today, after numerous improvements and two expansion projects, the concentrator is an interesting combination of old and new equipment. The regrind mills, for example, have been in service for about 50 years, while the ceramic concentrate filter represents the latest technology.

Jan 1, 1993

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By Rob Herr, Irwan Halim, Heather Marsh

This project will expand sanitary sewer within the City of Columbus. It consists of 2.5 mile long, 72-inch finished diameter pipe grouted inside 10.8-foot diameter tunnel excavation in shale. This paper describes the multi-faceted geotechnical exploration to minimize the underground risks. The tunnel will cross below a buried valley with minimum cover of highly weathered rock. The risk mitigation to cross the valley includes contingencies and cost allowances. Provisions to prevent impact on adjacent groundwater resources will be described. Latest construction updates will be provided including contractor alternate shaft support and pre-excavation probing to mitigate tunneling risk below the valley.

Jun 23, 2024

By B. H. Kim, S. J. Schatzel, K. M. Ajayi, G. S. Esterhuizen, D. W. H. Su, Z. Khademian

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a Discrete Fracture Network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A Fracture Flow Code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.03 m3 /s, significantly lower than the average inflow of 0.92 m3 /s for a shallow-cover mine (145 m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk

Mar 2, 2022

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the important parameters influencing gold recovery. The model was used to direct modifications to plant operating practice. The cyanide-dosing strategy was changed to reduce gold losses from preg-robbing and to cut reagent consumption. A finer grind was achieved without capital investment. The density in the carbon-in-leach circuit was lowered, and tighter control was exercised over the plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz ($9.64/g) gold, and concomitant reagent cost savings of $55,000/ month.

Jan 1, 2000

By John C. Ruckmick

Elemental sulfur deposits generally can be classified as either volcanogenic or biogenic. The latter can be divided into biosyngenetic and bioepigenetic deposits. Essentially all economically important sulfur deposits are bioepigenetic replacements of anhydrite or gypsum in basins containing evaporites and hydrocarbons. Anaerobic bacteria utilize the oxygen of sulfate ions to oxidize hydrocarbons to C02 and reduce the sulfate to H2S. Sulfur deposits are formed by concomitant and subsequent oxidation of the H2S. These bacterial systems can operate on enormous scales, producing deposits containing over 200 million tons of elemental sulfur. There are no known "old" sulfur deposits; almost all known deposits are younger than Miocene and most are still actively forming today. Therefore, it is probable that, with burial and time, sulfur deposits are converted to sulfide deposits. Perhaps more important, bacterial oxidation of hydrocarbons and resultant production and trapping of large quantities of H2S appears to be the logical explanation for the location of many important metal sulfide deposits such as the Mississippi Valley type lead and zinc deposits.

Jan 1, 2013