Search Documents

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The phosphorus journey begins with the extraction of primary phosphorus in the form of phosphate in apatite through openpit mining and, in some rare cases, underground mining methods. The ores are processed in beneficiation plants to remove impurities before the phosphate rock concentrate is either sold on the open market or converted into phosphoric acid in downstream chemical production facilities by the wet acid process or thermal phosphorus routes. These can in turn be converted into fertilizers, as well as used in the food and electronic industries. The advent of the EV battery has given rise to a new use for purified phosphoric acid in the production of lithium ferro phosphorus (LFP) cathode material for EV battery cathode assemblies. The production of LFP relies on raw materials such as lithium carbonate, lithium hydroxides, iron salts and purified phosphoric acid.

Feb 1, 2024

By Thomas Pea, Heiner Kontrus, Jérôme Steinkühler

In tunnel condition assessment, the trend is towards comprehensive 3D measurement combined with high quality image texture to document and quantify damages to the tunnel surface and to create a cohesive data base of the structural conditions throughout its lifespan. The faster such measurements can be made on site, the less it impacts traffic conditions of the highly sophisticated subway systems. The Dibit high-speed 3D scanning system which is based on Photogrammetry and LiDAR technology enables data acquisition in tunnels at a speed of up to 60 mph. Given the high rate of speed the system can operate, tunnel shutdowns can be drastically reduced, and tunnel safety increased. The photorealistic texturing of the 3D-model allows the identification and analysis of smallest material damage (e.g., cracks ≥0.3 mm wide). The publication illustrates technical details and 3D results of the innovative system from measurements that were performed in the subway tunnels of the Bay Area Rapid Transit System in San Francisco, CA (total length 66.23 km).

Jun 13, 2021

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By Richard Giffen, Boris CARO VARGAS, Terrence Carroll

"This paper takes an in-depth look at the $72 million design-build Norris Cut project, which includes the replacement of an existing 54-inch waste water sewer main to Fisher Island under the Norris Cut Channel. Tunneling through one of the country’s most unpredictable geologies created unique challenges in both the design and construction phases of the project. The paper presents the geotechnical and structural design considerations for the 100-foot deep secant piled TBM launch shaft in the highly permeable Fort Thompson formation limestone and sands. The structural design effort also included the design of the tremie slab, thrust wall and design of the largely unreinforced launch shaft to resist asymmetric loading from partial ground freezing. The retrieval shaft was designed as a deep soil mixed shaft and is thought to be the deepest soil-mixed shaft in Miami. From a construction perspective, this paper discusses the unique challenges of building two shafts with two different techniques and will compare some of the constructability aspects, costs and equipment schedule-considerations related to the use of two separate techniques. INTRODUCTION Nicholson Construction Company (NCC) was awarded a $72.1 million Design-Build contract to replace an existing force main from the Virginia Key Central District Wastewater Treatment Plant (CDWWTP) under the Norris Cut Channel to Fisher Island. The location of the project is shown in Figure 1. The project involves replacing an existing 54-inch diameter pre-stressed concrete sewer force main with a 60-inch diameter fiberglass force main. Arup USA, Inc. (Arup) is the lead designer for Nicholson on this design-build project. Arup is providing design services for the TBM launch and retrieval shafts, segmental tunnel lining, the fiberglass pipe, and the horizontal directional drill component. Miami-Dade Water and Sewer Department currently owns and operates the existing 54-inch sanitary force main that transmits sewage collected from Miami Beach and Fisher Island to the CDWWTP for treatment and disposal. The existing force main was subject to a condition assessment in December 2011 which revealed structural deficiencies in the pre-stressed concrete pipeline."

Jan 1, 2016

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By John Kuyt, Zili Li, Michael Mooney, Michele Mangione

"INTRODUCTIONTwin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world. A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a betterunderstanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This paper discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link Project OverviewThe Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with over 7km of twin-bore road tunnels, two lanes each, with several caverns, interchanges, and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a Public-Private Partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5m double-shield Herrenknecht TBMs [1]. The TBMs were used in EPB-type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1 m diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in a 9 segments + 1 key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis [2]. Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Jan 1, 2016

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023

By William C. Peters

"A large proportion of the earth's surface is blanketed by young sedimentary formations and by recent lava flows. How many Guanajuatos lie concealed beneath the rhyolitic capping of the Sierra Madre of Mexico? How many Kirkland Lakes are under the drift cover of the Canadian Shield? How many Wilunas are still hidden by the alluvium of the desert of Western Australia? How many ore deposits lurk underneath the basalt-covered plateaus of the Columbia River region? If erosion at Goldfield, Nevada, had stopped 100 feet higher, probably no ore would have been exposed. How many Goldfields are still awaiting discovery?" --Hugh Exton McKinstry, 1948

Jan 1, 1969

By Peter Johnson, David Barber, Lachlan Henderson

"Within underground portions of metro rail networks the traditional approach to a design fire has been to assume a worst credible railcar fire and develop ventilation and egress measures for life safety. This approach is being challenged as a rail network approach to design fires becomes a more practical and realistic approach. The network approach is based on utilizing an in-depth hazard analysis, to understand ignition and fire load sources in tunnels, above and below the floor of the railcar and within stations, and then utilizing a quantitative risk assessment to determine sets of fire scenarios. The process allows small, medium and large fires to be considered, with the consequences also being quantified. The selection of design fires has a significant influence on fire protection measures within a metro network and hence, is a major cost input. The rail network approach provides more robust decisions on fires, based on the hazards present. INTRODUCTION A fire within a rail car or one that occurs as part of a rail system can threaten the lives of users, maintenance staff and emergency services personnel. Fires in metro systems are rare events but can have severe consequences. As a result, any analysis of a potential fire must be thorough and rigorous and address not only regular accidents and small fires, but also very low probability, high consequence scenarios. The fire safety design process for a tunnel and station must start with the design engineers, contractor and operators making a number of key decisions related to fire protection measures, which may have significant cost considerations. One of the key aspects that influences the required fire protection is the design fire and the design fire scenarios, which is a key input for analysis. This paper provides an overview of the author’s experience in designing fire protection measures for rail networks in Europe, Australia and NZ, where a risk based framework is used to develop design fires and scenarios for the whole rail system – trains, stations and tunnels. This system wide approach is innovative, challenges the norms, but provides significantly more informed outcomes. The range of design fires will include small fires that may halt the network, larger fires for smoke hazard system design and significant post-flashover fires to assess the structural response."

Jan 1, 2016

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By M. Li, J. K. Thompson, A. S. Azman

"Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Office of Mine Safety and Health Research (OMSHR) of the National Institute for Occupational Safety and Health (NIOSH) developed a useful tool to estimate the hearing loss due to occupational noise exposure in a systematic way and evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software. INTRODUCTIONPeople regularly exposed to noise can develop hearing loss at different levels of severity depending on a number of factors. The resultant hearing loss can affect one’s ability to understand speech, learning, acoustic signal perception, or appreciation of music. Hearing loss caused by overexposure to noise has long been recognized in literature. However, it still does not get serious attention by those working in noisy environments because the loss of hearing ability is a gradual process and workers are often unaware until the damage becomes an apparent problem. In the United States, occupational hearing loss is one of the most common work-related illnesses. Depending on the definition of exposure and impairment, in 2012 the National Institute for Occupational Safety and Health (NIOSH) estimated that there are between 5 and 30 million workers in the U.S. who are exposed to noise levels at work that put them at risk of hearing loss.4 In the mining industry, noise-induced hearing loss (NIHL) is particularly severe due to the fact that heavy-duty machinery is widely used to improve production efficiency, and this machinery can generate much higher-level noise than the permissible level defined by regulation. As a result, the mining sector has the highest prevalence of hazardous workplace with high noise exposures (76%) among all industrial sectors."

Jan 1, 2015

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By D. L. Monroe

Technical service is assuming an increasingly important role in the sale of asbestos fibre,, Manufacturers are examining raw materials more closely than ever before in order to, obtain the most efficient usage in their processes. Asbestos is one of the more difficult materials to evaluate and consequently has been are of the last to be subjected to evaluation. The main problem encountered in the evaluation of asbestos fibre is that minor differences in grade and texture are not shown up by chemical analysis, and are identified only by specialized physical analyses or actual production use. However, such minor differences become more critical as manufacturing processes are made more efficient, and many purchasing agents and plant chemists are applying a closer scrutiny to their supply of raw asbestos fibre. Many processes have been formulated around grades and qualities of asbestos fibre, which were standard some time ago, but which may now be subject to modification and improvement.

Jan 1, 1959

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

By KAGAN BENZESIK, OMUR CAN ODABAS, SELCUK KAN, Onuralp Yucel

In this study, domestic molybdenum disulfide (MoS2) concentrate was roasted in a chamber furnace and then in a rotary kiln. The behavior of the roasting process was examined in both furnaces, and which type of furnace is more advantageous to use in mass production was investigated. It is theoretically possible to roast in a chamber furnace, but a major problem was observed when the amount of concentrate was increased in the chamber-furnace experiments. The problem was solved by using a rotary kiln. This study improves the understanding of the roasting of  MoS2 concentrate and presents a different perspective to the industry, showing that rotary kilns can also be used for roasting.

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023