Search Documents

By D. W. Fuerstenau

One of the more energy-efficient methods for size reduction, namely particle-bed comminution under high compressive loads, was employed to grind eight minerals and ores, using up to 250 MPa pressure. A new approach based on the self-preserving character of the ground product size distributions and a linear energy-reduction ratio relationship is proposed for analyzing this mode of size reduction. The grind ability of the material when comminuted in a particle bed is about one-half that of the single-particle crushing mode, which is in agreement with previous estimates of the relative efficiencies of energy utilization based on direct measurements of surface area produced. The loss of efficiency may be attributed to energy dissipation by particle interaction phenomena in compressed beds.

Jan 1, 1993

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

By M. J. Hart

There are no formulas that guarantee success when it comes to obtaining zoning approval for mineral aggregate mining. Local land use decisions often times represent the most controversial issues faced by community. Public awareness, concern, willingness to get involved, sensitivity to the environment and probably most importantly fear of change only begin to describe the atmosphere in which local land use decisions are made. Add to this the public hearing process which is quasi judicial, adversarial, and unfortunately not designed for resolution of disputes and it is not difficult to see the need for an alternative to present methods. Hopefully, some day we will have a process that will do away with or at least minimize unnecessary, unproductive and unmanageable community conflicts.

Jan 1, 1984

The vast coal resources of North Slope, Alaska can be expected to attract substantial interest because the nearly flat lying coal beds of the coastal plan are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large scale coal mining and reclamation operations have not been carried out in the arctic The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the interrelationship between the problems due to permafrost and factors in reclamation of post mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1986

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By R. S. Saunders

Congress, under the Nuclear Waste Policy Act of 1982, as amended, charged the U.S. Department of Energy (DOE) with the responsibility for safe and permanent disposal of high-level radioactive waste in a geologic repository. The waste will consist of spent fuel from commercial nuclear generating plants and reprocessing activities. Under direction of this law DOE is currently evaluating Yucca Mountain in Southern Nevada as the candidate site for a potential high-level radioactive waste repository. Presidential, Congressional and State of Nevada approval are needed for repository construction to proceed after successful completion of site characterization and recommendation of the site to Congress. The DOE will submit a license application to the Nuclear Regulatory Commission (NRC) to construct the geologic repository. Following successful construction DOE will update its license application to operate the repository.

Jan 1, 1993

By J. James Eidel

Geological interpretations generally require projections from direct observations at the earth's surface. Crustal projections include mineral deposits as well as the geochemistry of the crust and its fluids, structure and tectonics. Drilling offers opportunities for verification of the required projections, and is thus a required step in furthering crustal understanding. Like any new science, the direct observations that drilling provides commonly generate major surprises and stimulate totally new ideas. Drilling is costly. There are many critically important scientific problems with societal and potential economic benefits in mineral deposits which have not been drilled because the holes are difficult to justify as economically sound risks for private capital. Such holes, however, are highly justifiable research goals for government because of the significant new opportunity for ore deposit insight and exploration that they afford. The earth science community is prepared with excellent drilling projects for research in mineral deposits.

Jan 1, 1985

By Gerrit V. R. Goodman, Fred N. Kissell

The Bureau of Mines has evaluated the effectiveness of the safety elements used to prevent tunnel methane explosions. These fa1l under the general categories of better ventilation, better gas monitoring, reducing ignition sources, and improved worker training. For this evaluation, a technique called fault-tree analysis was used to analyze questionnaire responses from 27 tunneling experts. This analysis allowed us to rank the effectiveness of each safety element, and indicates where money is best spent to reduce the chance of a methane explosion. Results indicated that large decreases in the explosion hazard only take place with the simultaneous application of several elements. Most of these involve a human component - the everyday vigilance and awareness of those working underground.

Jan 1, 1991

By Alfred Weiss, Andrew E. Nevin, Thomas J. Neil, O&apos

As Edward E. Runyan, 1983 AIME President, in an interview excerpt in ME, June, p. 607, stated, "...the AIME Transition Committee has recom¬mended to the AIME Board that each Constituent Society be allowed the option of separate incorporation, whereby each could become its own separate legal entity." Background The American Institute of Mining Engineers (AIME) was formed in 1871 by 22 engineers in Wilkes-Barre, PA. Although originally a mining organization, it became a home for metallurgists, iron and steel industry people, and for the individuals in the expanding petroleum engineering profession. There are now four Constituent Societies: Society of Mining Engineers, located in Littleton, CO, 29,000 members; Society of Petroleum Engineers, located in Dallas, TX, 47,500 members; The Metallurgical Society, located in Warrendale, PA, 10,000 members; and Iron and Steel Society, located in Warrendale, PA, 6,500 members. Each of the four groups has grown and continues to serve the specific and/or diverse needs of its membership. As the needs and requirements of their industries and professions change, each of the Societies has perceived and initiated programs that serve their constituency rather than AIME as a whole. Therefore, each Society has recognized an increasing need for autonomy to better augment their own programs. An AIME Ad Hoc Transition Committee, with Robert Merrill, AIME Past President, as chairman, made a number of recommendations pertaining to AIME operations that were approved in October 1982 by the AIME Board of Directors. One of the recommendations was to endorse separate incorporation of the Constituent Societies on an individual-society-option basis. The AIME Board commissioned a task force of Constituent Society representatives to develop specific revisions to the AIME Certificate of Incorporation and the AIME Constitution and Bylaws. This was done to allow separate incorporation and to reflect the decentralized structure of the Institute. The SME-AIME Board of Directors subsequently approved the recommendation of SME Working Party #69 that SME pursue separate incorporation. Meanwhile, Working Party #69 continues to work with the other Constituent Societies and with the AIME Task Force on Reorganization to determine the form and substance of the separate incorporation. Why Incorporate? George Webster in The Law of Associations quoted Chief Justice Marshall's (1819) definition of corporation as: "A corporation is an artificial being, invisible, intangible, and existing only in contemplation of law. Being the mere creature of law, it possesses only those properties which the charter of its creation confers upon it, either expressly or as incidental to its very existence. These are such as are supposed best calculated to effect the object for which it was created." SME-AIME attorneys, Davis, Graham & Stubbs, have pointed out that the status of an organization operating as an unincorporated association is always unclear. At present, SME-AIME administers assets of almost $3.5 million (mainly property and inventory) but technical ownership and ability to enter into contractual relationships resides with AIME. However, the operation appears to outsiders (particularly those with whom SME-AIME does business) to be an independent operation which would be expected to be a legal entity in its own right. Advantages of Incorporation Liability. Because of legal ownership by AIME of all assets of the Constituent Societies, those assets are subject to the claims of any of the creditors of AIME or any of its constituent parts (i.e., the other societies). Liabilities can be those usually encountered in business but also encompass special risks, which could develop if there were a careless and erroneous publication of material that might be used in practice or if standards are improperly established. The recent US Supreme Court decision in American Society of Mechanical Engineers, Inc.,

Jan 10, 1983

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By Christopher E. Dianora, Matthew Sorrell, Eileen Test

"Constructed between 1939 and 1945, the Rondout-West Branch Tunnel (RWBT) portion of the Delaware Aqueduct is 45 miles (72 km) long. The New York City Department of Environmental Protection (NYCDEP) first identified suspected areas of leakage from the RWBT in the 1990s. A $1 billion project is underway to mitigate the leakage through the construction of a bypass tunnel around the area of most severe deterioration, a 2.5-mile (4 km) section located beneath the Hudson River. Two shafts, 800 and 900 feet (244 and 274 m) below the ground surface, are being sunk to support the tunnel construction. The deep shafts will be subjected to high groundwater pressures and have been designed to accommodate multiple tunnel portals. This paper discusses the engineering decisions and analyses leading up to the final design. INTRODUCTION Project Background The New York City Department of Environmental Protection (NYCDEP) provides over 1 billion gallons (3.7 billion liters) of water to over 9 million residents of the City of New York and surrounding communities each day. This water is stored in upstate reservoirs and conveyed to the City via a system of aqueducts and tunnels. Water is delivered to the City almost completely by gravity and consists of three systems: the Croton, the Catskill, and the Delaware. The Delaware System is the largest of the three and supplies between 50% and 70% of the City’s daily water supply. In the 1990s, the NYCDEP discovered leaks in the central 45-mile-long (72 km) portion of the Delaware Aqueduct known as the Rondout-West Branch Tunnel (RWBT). The leaks release between 15 and 35 million gallons per day (MGD) (132.5 million liters per day) and are concentrated in two areas near Wawarsing and Roseton, New York. As part of the Rondout-West Branch Bypass Tunnel and Wawarsing Repairs Project (Bypass Tunnel Project), the leaks in the Wawarsing area will be repaired by grouting from inside the existing RWBT, and the leaks in the Roseton area will be mitigated by constructing a bypass tunnel parallel to and 1,750 feet (533 m) north of the leaking portion of the existing RWBT. Two deep shafts will be excavated on either side of the Hudson River: Shaft 5B in Newburgh and Shaft 6B in the Town of Wappinger."

Jan 1, 2016

By M. R. Shahan, W. R. Reed

A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports, or shields. The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances. This paper will outline the design parameters for the development of the system, as well as describe baseline testing of coal and limestone dust. Results show the average instantaneous respirable dust concentrations that occurred during simulated shield advance. Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device. INTRODUCTION During longwall mining, miners can be exposed to respirable dust that is generated during the advance of hydraulic roof supports or shields. National Institute for Occupational Safety and Health (NIOSH) researchers have conducted numerous surveys of longwall mining operations, benchmarking the operating practices and dust control measures in use. It has been determined that the shields are responsible for 27% of the respirable dust that is generated on the longwall face [1]. The dust generated by the shield advances ranks second, next to the longwall shearer which is accountable for 43% of the respirable dust generated on the longwall face. The respirable dust generated during the advance of the shields can be a significant contributor to the respirable dust exposure of the mining personnel operating at the longwall face, especially since some of this dust is generated in the walkway. Control systems designed to reduce the dust levels generated during the shield advance have the potential to greatly reduce the respirable dust exposures of the personnel downwind of these activities. One control technology to decrease the dust generated by the shield advances would be to apply a layer of foam to the forward shield-roof interface prior to the shield advance [2]. The blanketed layer of foam would interact with the material located on the top of the shield during the advance, preventing a portion of that dust from becoming entrained in the mine air. This layer of foam would be applied using a foaming nozzle located on the longwall shearer body that would spray foam on the roof surface as the shearer passed. Substantial laboratory work has been completed to determine the feasibility of this type of foam application. NIOSH engineers have classified the various characteristics of foaming agents, using foam expansion ratio and drainage as important properties, as well as developed the mechanical systems required to apply the foam safely to the mine roof [2, 3]. The construction of an apparatus that could simulate the mechanical interaction between the dust-laden shield top and mine roof was necessary to adequately test the hypothesis that foam could be an appropriate control. A team of engineers designed and constructed a shield dust simulator system allowing for in-house testing prior to a full-scale field investigation.

Jan 1, 2019

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By F. L. Pirkle

A heavy mineral deposit about 1.6 km (1 mile) in length, 0.13 km (0.08 mile) in width and averaging about 3 m (10 ft) in thickness is exposed approximately 130 km (80 miles) east of Denver, along Interstate 70, in Elbert county, CO near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium ridge. The dominant heavy minerals, accounting for about 70% of the total heavy-mineral suite by weight, are ilmenite, garnet and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Ga. Thus, Titanium ridge provides evidence that heavy-mineral accumulation models for late cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2012

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012

By L. Zhou, L. Yuan, D. Bahrami, Y. Xue

Underground mine accidents, such as mine fires, remain a health and safety risk to mine workers. Researchers at the National Institute for Occupational Safety and Health (NIOSH) are developing a data-driven, predictive model for characterizing the location and size of unknown underground fires. This study examines applying a machine learning-based model to predict fire size and location in a large underground metal mine based on hypothetical scenarios on the model performance. The results show that the size and location of an unknown fire can be determined with over 80% and 90% accuracy, respectively, and potentially help to reduce the risk of hazardous conditions for emergency response.

Feb 1, 2024