Search Documents

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

Updating the openpit vehicle transportation network has the problem of being time consuming and low precision. To address this problem, a high-precision road network model construction method for unmanned vehicles in openpit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3+C (DeepLabv3+Concat) is presented, and the road information extracted by the DeepLabv3+C network is used to construct a three-dimensional model of the openpit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicles meeting in openpit mines, a vehicle meeting strategy is proposed. This strategy is used to guide the navigation of unmanned vehicles in openpit mines. At the end of the study, vehicle running simulation was carried out on the road network model using Unity, a 3D visualization simulation software. The high-precision unmanned road network model of openpit mines studied in this work can further promote the construction and development of smart mines by acting as a high-precision map for unmanned vehicles.

The past decade has seen remarkable progress by the railroads both in equipment and concepts in the handling of dry bulk. materials. While such shipments have always been an important part of the traffic handled by the railroads I little was done to improve the efficiency of handling or toward attempted optimization of equipment design before 1960. Several developments at about that time turned attention to this important segment of railroad traffic. One was the construction of a successful coal slurry pipe-line. Another was the promise of substantial economy in electric power transmission by ultrahigh voltage systems and finally, came the growing technological and economic feasibility of nuclear fuel electric generating plants. Each of these developments was a threat to the coal traffic of the railroads --the most important single commodity they handled in terms of revenue and tonnage. By the mid-1950's I Southern Railway management had become most concerned with its growing investment in freight car equipment and the declining revenue productivity of the capital employed. Additionally I there was substantial concern with the loss of business and potential losses in the area of the railroad's greatest economic advantage --bulk commodity movements. In 1958 a small team was established to study this problem. They arrived at two conclusions. The first conclusion was that within limits of maximum gross allowable weight on rail the lowest unit net capacity cost of investment came at maximum allowable gross weight per car unit. The second conclusion was that with a high degree of utilization costs per weight unit transported could be reduced to the pOint where

Jan 1, 1971

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By J. M. Keane

Critical to successful dump and heap leaching for copper is an adequate testing program for evaluation of the applicable parameters. This paper deals with testing methods to establish best conditions for dump and heap leaching of copper so that commercial operations can proceed on a rational basis. Discussion is also offered of ore occurrences suitable for dump and heap leaching.

Jan 1, 1985

By J. R. Beeder

Minerals Engineering Company (MECO) is a relatively small, promotionally oriented mineral exploration company founded in Colorado in 1948 during the height of the uranium boom. The company has been: 1. in uranium exploration and production 2. a drilling company 3. a manufacturer of Geiger counters 4. a major tungsten producer 5. then dormat for several years and 6. now we are back into exploration on a broad scale. We have been in underground lead and zinc production in the 1970's but we are now involved primarily in "wheeling and dealing" in mineral exploration. The company has had diverse interests in the past and we are presently diversifying to some extent into oil and gas ventures.

Jan 1, 1979

By Ronald Ludchak

Since coal has been designated as the short-term answer to the threatening world energy crisis, improved surface mining techniques, along with improved extraction and handling equipment, are needed to increase the amounts that can economically be mined by open pit methods. A dwindling supply of low cost oil and gas have dictated a major rethinking of our energy sources and their use. New methods for open pit coal mining have to be found to increase coal production and to meet more stringent reclamation laws. Modern twin-engine elevating scrapers can play a vital role in meeting these needs. They are readily available, with short delivery times, from several experienced manufacturers of earthmoving equipment. Recent developments of the elevator system have extended its working range to include many of the materials commonly encountered in open pit mining. The paper deals with the advantages of using twin-engine elevating scrapers in the performance of various mining tasks. These tasks range from utility work to the major task of using the scrapers as a primary stripping toot and, of even more importance, a stripping- reclamation tool for, with scrapers, the overburden can be moved and redeposited in the same strata sequence or soil horizon as in its natural state. A recap of current applications of the elevating scraper will be presented, along with proposed uses.

Jan 1, 1975

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By Edmund C. Bitzer

The unit costs of dry crushing, within the efficient reduction ranges of equipment now available, are considerably less than those for the reduction of the same material in the same size range by wet mills using grinding media. This is a commonly recognized fact which cannot be disputed; still we find considerable imbalance in costs between the crushing and grinding sections of many operating mills. In other words, there are many instances where more reduction could be accomplished in the lower cost area of dry crushing. In addition, equipment is now available which enlarges this area and makes it possible to consider much finer crushing than has been heretofore economically feasible. There has been a tendency for the past two decades to utilize wet rod-¬milling in the reduction step. This actually amounts to a fourth stage of crushing in a size range formerly served by roll crushers which have fallen from favor on account of high operating costs, Some investigations have indicated that there is not sufficient difference in the operating costs of rolls and rod-mills to give a clear cut advantage to either method, There has for some time been a need and an opportunity for a dry crushing process to improve costs in the range now served by these two systems.

Jan 1, 1965

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By A. Bruynesteyn

Many papers 'have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

With mine activity dating back to 1792, the Lehigh Valley, about 80 km (50 miles) northeast of the historic Allentown/Bethlehem steel mills and about 160 km (100 miles) northeast of Philadelphia, PA, defined early-day coal mining. Coal mining began just nine years after the end of America?s Revolutionary War. The high-carbon, clean-burning anthracite coal that was hand-dug from the Pennsylvania hills fueled the steam engines that powered the Industrial Revolution, helping build early steam ships and even the first automobiles. Around 1910, at the peak of the U.S.?s early mining effort, there were more than 250,000 men working underground ? 10,000 of them in the Lehigh Valley.

Jan 1, 2012

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

By Per H. Fahlstrom

The story of the Aitik mine begins in the early thirties. At that time blocks of low grade chalcopyrite impregnations were found in Swedish Lapland not far from the present mine, some 40 miles north of the arctic circle in the vicinity of the iron ore field at Gällivare. The ore prospect was viewed upon several times. By means of geophysical studies and an extensive diamond drilling programme during the end of the fifties and the beginning of the sixties a huge low grade ore body was discovered under the muskeg overburden. In 1965 55 million tons of ore with 0.5 % Cu was known to a depth of 160 ft. In 1970 the ore reserves had increased to 165 million tons with 0.40 g, Cu at a depth of 400 ft. Decision to develop the mine and to start production at an annual production of 2,2 million tons was made in 1965. A mine and concentrating plant, the A section, went on stream in 1968. In 1970 decision was made to expand the production with 3,3 million tons pr year. A second section of the plant, the B section, went on stream during the end of 1972 and the beginning of 1973 The production in the initial plant has been increased to 3,1 million tons pr year and during 1974 the combined A and B sections are expected to treat' about 7,2 million tons of ore. The two sections will treat 10,000 and 13,000 tons per day.

Jan 1, 1974

By D. M. Urich

This paper is a follow-up on a previous paper presented at the A.I.M.E. Meeting in Chicago, Illinois, on February 17, 1965, by Mr. D. Kelly Campbell. Mr. Campbell's paper was presented prior to the operation of the Eveleth Taconite-Company's Plant, and this paper outlines and reports on the operation and performance of the Plant after the first nineteen months of operation.

Jan 1, 1967

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By J. M. Duke

Significant resources grading less than about 1 % nickel occur in magmatic sulfide deposits of two types. In the Mt. Keith type, extensive zones of disseminated nickel sulfides occur in the central portions of certain synvolcanic dunite-peridotite sills of komatiitic affinity in Archean greens tone terranes. In the Duluth type, disseminated copper-nickel sulfides occur near the basal margins of intrusions of flood basaltic affinity associated with intracontinental rifting. In both types, the parent magmas became saturated with sulfide following the onset of fractional crystallization and the separation of the immiscible sulfide melt was accompanied by the precipitation of a relatively large proportion of silicates. The abundant silicate crystals impeded the coalescense and accumulation of the sulfide droplets with the resulting formation of large but low grade deposits.

Jan 1, 1982