Search Documents

By Diler Katircioglu-Bayel

This manuscript aimed to examine the impact of operating parameters on the wet grinding of talc in a vertical-type stirred media mill. Within the scope of the research, the effects of operating parameters including media filling ratio, solid mass fraction, grinding media size, and grinding time were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw), and energy consumption (Em). As a result of the present research, the following optimum grinding test conditions were determined: 65% media filling ratio, 40% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. After determining the optimum grinding conditions, the Box–Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio was found to significantly affect the decrease in d50 compared to the other two parameters. Furthermore, the minimum d50 size was also achieved under optimum grinding conditions.

Aug 12, 2020

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By S. Mukusha

Electronic spreadsheets are the most common and readily available software applications for analyzing and modeling quantitative problems. Spreadsheets can offer a vast array of opportunities for the analysis and modeling exercises encountered in the field of geomechanics. This study explores the potential for using spreadsheets of in the practice geomechanical engineering. The study also examines some of the barriers to widespread use of spreadsheets. Best practices and guidelines for overcoming potential pitfalls are discussed and highlighted through a case study.

Jan 1, 2000

By Chris Tattersall, Tomyuki Kudo, Peter Raleigh, Nestor Garavelli, Steve Redmond, Michael J. Lehnen

Twin bore running tunnels driven approximately 4,500 route feet by a Mitsubishi Heavy Industries (MHI) EPB Tunnel Boring Machine link the West Portal and East Portal on this complex Light Rail Project. One third along the way, the TBM arrives at the Beacon Hill Station which is the deepest underground “binocular” station of its kind in North America and then “walks-across” the station to be re-launched on the other side to complete the drive. This paper discusses briefly the layout and design considerations but then focuses more deeply on the approach by the Contractor to drive and supply the tunnel. The paper addresses the approach used to launch, re-launch and recover the TBM and touches briefly on muck volume control and monitoring plus settlement monitoring and the performance achieved. Also of interest is a unique solution to a difficult launch situation involving a secant pile tieback wall designed with several rows of double I-beam steel walers spanning the eye at the West Portal under the I-5 freeway.

Jan 1, 2007

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By J. S. Young

During 1975, the Reclasource Corporation constructed and commissioned a plant for the recovery of mill scale, coke breeze, blast furnace dust, blast furnace sludge and basic oxygen furnace dust at the site of Crucible Alloy Division, Midland, Pennsylvania. The Reclaform Process was employed as the criteria for plant design. This Process takes the solid in-plant fines as listed above, commonly found in integrated steel mills, sizes and forms them through the use of a carbonaceous binder briquetting system and cures the binder through a final heat-treating step. 15,000 tons of Reclaform briquets have been tested in the Crucible blast furnace in several campaigns structured to assess material handling properties, burden feasibility and finally culminating in an iron and carbon assessment campaign. Data are presented from the records of the blast furnace operation and conclusions are drawn that both iron and carbon utilization have been demonstrated.

Jan 1, 1977

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By Laszlo Toth

A feeder is used to control the gravity flow of bulk solids from storage areas, like a bin or a stockpile. For this type of application, it is important to select a proper drive that can fulfill all of the demands put on it. High starting torque capacity, variable speed and the ability to handle frequent starts and stops are some of the demands that the drive must be able to meet. The following is a comparison of the most common type of drives used today for feeder applications. When a feeder is started, the breakaway torque may reach as high as200% of the running torque. The accelerating torque usually is set to protect the carrying element of the feeder, like the belt for the belt feeder and the carrying chain of the apron feeder (Fig. 1).

Jan 1, 2003

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

By J. Kretschmann, A. Müterthies, T. Rudolph, C. Yang, P. Goerke-Mallet

Catastrophic failures of dams and tailing storage facilities (TSF) have triggered the development of integrated ground monitoring concepts for hazard assessment, risk management and public safety. These concepts are based on knowledge and expertise of persons technically responsible for TSF. The aim is to combine this implicit and explicit knowledge with the data of in-situ- and remote sensors. Risk management for TSF must include a comprehensive monitoring program that integrates data from ground based-, air-borneand satellite-based sensors. Researchers at Technical University Georg Agricola (THGA) in Bochum, and EFTAS, Muenster, Germany, are fusing a variety of sensor data to enhance the capability and performance of TSF monitoring to ensure public safety downstream of TSFs. This paper describes the variety of sensors implemented in numerous research projects. It gives an outlook in terms of planned satellite missions with innovative equipment like hyperspectral sensors. The implementation of the data of these sensors in the analysis will increase the understanding of spatio-temporal impacts of mining activities. Future opportunities are explained by a datacube approach.

Mar 2, 2022

By J. -F. Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

Jan 1, 2011

Characterization of ore and waste-rock material using automated quantitative micro-mineralogical techniques (e.g., QEMSCAN® and MLA) has the potential to complement traditional acid-base accounting and humidity cell techniques when predicting acid generation and metal release. These characterization techniques, which most commonly are used for metallurgical, mineral-processing, and geometallurgical applications, can be broadly applied throughout the mine-life cycle to include numerous environmental applications. Critical insights into mineral liberation, mineral associations, particle size, particle texture, and mineralogical residence phase(s) of environmentally important elements can be used to anticipate potential environmental challenges. Resources spent on initial characterization result in lower uncertainties of potential environmental impacts and possible cost savings associated with remediation and closure. Examples illustrate mineralogical and textural characterization of fluvial tailings material from the upper Arkansas River in Colorado.

Feb 27, 2013