Search Documents

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By A. T. Yu

Technology and economies of scale have, in the past decade, brought about the emergence of giant vessels. Meanwhile, to answer the need for rapid dispatch, as a means of combating the proportionately far greater demurrage charges, shiploading and unloading speeds have soared (Ref. 1, 2, 3). As the loading and unloading rates have dramatically increased, so has the cloud of dust grown in unbearable proportions. It not only has threatened to be a real menace to machinery and men, but in certain instances has also seriously jeopardized fish and marine life (Ref. 4). In an era when ecology is king, dust in shiploading and unloading can no longer be shrugged off as a mere public nuisance, and its control is now duly recognized as of grave concern to all. Even if public outcry were not a problem, from the operator's own parochial point of view, dust can adversely affect productivity and the well-being of the operating personnel. Without adequate control, it can also result in costly equipment maintenance, particularly when the dust is micronic in size, and abrasive. The Hierarchy of Control Techniques Given the great fortune of not yet having to deal with gas and odors, in the jargon of pollution control, our problem is confined to having to control "particulates" only. To deal with "particulates", the myriad of dust control techniques can be utterly confusing to those who are not entirely well versed in the methodology. Our analysis of what is available to date results in the following hierarchy of logical preferences: 1. Prevention 2. Removal 3. Suppression 4. Containment 5. Dilution Since it deals with the root cause, prevention always outranks the cure. Once the dust is generated, removal nips it in the bud. Only when dust removal is

Jan 1, 1972

By R. V. Ramani

In this paper, the application of the concepts of reliability engineering to the evaluation of longwall system performance is illustrated with data from an operating longwall face. A number of cases are analyzed to highlight the impacts of longwall equipment, geological conditions and outby haulage on systems reliability and availability.

Jan 1, 1988

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By Osvaldo A. Bascur

Standards and technology for bringing information to the desktop have greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure cooperative effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and database layers are emerging in successful client/server applications, the three-tier architecture.

Jan 1, 1996

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By W. W. Atkinson

This paper describes some concepts developed in a geologic data recording system at the Victoria, Nevada breccia pipe-skarn copper mine. The recording system is not fundamentally new, but represents expansion of earlier ideas. The paper is based on the philosophy that a high quality geologic data base is necessary and that it should be complete, clear, standardized, neat, quantitative, and readily useable. It may be multi-colored or simply black and white. Graphic, descriptive and quantitative recording of data is essential. A format for core logging is presented and discussed and as well as a multiple overlay system for recording data gathered in surface mapping.

Jan 1, 1983

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By W. C. Lacy

Traditionally Australia has been a leader in underground mining methods with world standards being established at Mount Isa, Broken Hill, Kalgoorlie, and Mount Lyell. With decline in higher-grade reserves and discovery of a multitude of near-surface oxide gold de-posits attention has shifted to bulk mining of low-grade gold ores by open pit methods, heap leaching and activated carbon recovery of gold values. The paper examines historical change in mining philosophy and the economic effects of isolation.

Jan 1, 1993

By A. Warren Wilson, Hugh R. Wilson

This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1986. Echo Bay Mines' Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle. The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that total containment was no longer applicable and therefore studies were undertaken to characterize the tailings, to evaluate the effectiveness of natural degradation of contaminants in the tailings pond and to determine what additional treatment steps would be necessary to meet the requirements of the mine's Water Licence. These studies indicated that arsenic and cyanide concentrations in the tailings pond decant water would not meet Water Licence discharge limits unless certain measures were under taken. As a result of this work, in late 1984 a decision was made to create a two-ponds-in-series system and the necessary civil work was started in 1985. In addition, a series of dykes were constructed to contain the solids portion of the mill tailings in a confined area of the first pond. To remove cyanide, the ponds are operated in a sequential fill and decant mode to take maximum advantage of natural degradation. For arsenic removal, a chemical feed system was constructed for iron salt addition to the decant stream from the first to the second pond. Decanting of the ponds is accomplished by means of a series of 500 mm (20 inch) Sclairpipe syphons.

Jan 1, 1987

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By F. Harold Weber

On July 13, 1967 the San Bernardino County Planning Commission approved publicly a request by American Smelting and Refining Company for a zone variance to conduct a silver mining and milling operation in the Calico district, southern California, Coincidentally, on July 14 the U.S. Treasury halted its sales of silver, and the U.S. free market price quoted rose immediately from $1.30 to $1.77 per ounce. In its request to the commission Asarco stated that about 13,500 to 15,000 tons of rock would be moved daily by surface mining, including 7,000 tons of ore. The ore would be crushed to minus three-quarters inches and the silver recovered "by a chemical process." The grade of the ore was not given, but the company said that it might also recover barite as a byproduct, The operation would employ 150-160 people. Additional activity in the district includes exploration programs by Superior Oil Company and Calico Silver Mines, Ltd. History and production: In retrospect, as the price of silver began to rise in 1961 from 91 cents an ounce, and as Asarco began its exploration program in late 1964, a new era for an old bonanza silver district would seem to have begun. The Calico district has been mined for silver only on a very, very small scale since 1882 to 1896, when an estimated $12 to $20 million (perhaps 15 to 20 million troy ounces) of that metal was produced from the 50-odd mines of the district and vicinity. These mines include the Silver King, Oriental, Waterloo, Garfield, Odessa and Waterman (which is about 8 miles west of the district). Much smaller-valued amounts of barite, gold, lead, and copper also have been produced from the ore deposits of the district; and from 1884 to 1907 the region yielded about $9 million worth of borate minerals.

Jan 1, 1967

By Richard H. Johnson

White Pine Copper Company began operating a plant designed to recover copper matte particles from its discarded reverberatory furnace slags in April, 1972. Seasonal operation, generally the months of April through November, continued through October, 1974, shutting down due to feed exhaustion. White Pine reverberatory furnace slags contained economically recoverable amounts of copper for a variety of reasons. Among them: 1. White Pine concentrates yield extremely high matte grades (65+% Cu) and viscous slags. The viscous slags hinder matte settling causing matte "prill" entrapment in the slag 2. White Pine's total refined copper output is accomplished through fire refining requiring special techniques for impurity removal, especially small amounts of nickel introduced from purchased pyrite and chalcopyrite fluxes. These special techniques result in high-copper slags, refractory to smelting, being reintroduced into the reverberatory furnace. 3. Furnace bottom build-ups resulting in mechanical matte entrapment through the formation of "dams" hindering matte flow. 4. Occasional concentrate fluxing and furnace atmosphere control problems.

Jan 1, 1975

By J. R. Evans

In order to patent an industrial mineral placer mining claim, it must incorporate an economic deposit. Each ten acre parcel is evaluated for its mineral -in -character nature. Nonmineral -in -character parcels cannot be patented. Economic concerns include: claim locations, dummy locators, common variety nature, "excess reserves," and environmental constraints. Also, geologic and mineralogic studies, sampling and testing procedures are vital. Mining, milling, processing cost, and taxes must be evaluated. Product marketability analysis is necessary before starting any cash flow or discounted cash flow study. Valid data is essential to evaluate an economic industrial mineral deposit.

Jan 1, 1997

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By A. C. Bigley

Before going into this subject, I would very much like to call to your attention some past history on patents granted by the United States Patent office that involved ammonium nitrate. On February 10, 1885, a patent was granted to Russell S. Penniman. "The object of this invention is to securely protect ammonium nitrate against deliquescent and to maintain it in substantially its normal disintegrated condition, so as to afford a new product suited for ready use in the manufacture of high explosives, and enable the immediate admixture thereof with any of the well known explosive substances or compounds heretofore employed. 'Whether the nitrate be thus granulated or otherwise reduced to a granular or divided condition, it is then thoroughly mixed with about twelve (12) percent of the fluid or semi-fluid carbonaceous protecting medium, which forms a readily applied jacket or coating for the granules of nitrate and also serves as a carbonaceous element in such explosive compounds as it may thereafter be employed in."

Jan 1, 1958