Search Documents

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By R. T. Torrie, J. R. Mernagh, D. B. Chambers

l, INTRODUCTION Uranium mine and mill workers are exposed to external gamma and beta radiation fields from radioactive ore. In the past the average uranium content of ores mined in the United States and Canada ranged from about 0.1% to 1.0% U308 with pockets of much higher grade ore. Holiday (1973) reported that radiation surveys in the U.S. uranium mines found mean gamma "radiation rates ranged from 0.20 to 0.70 mrem/h. Such radiation rates cause relatively insignificant exposures." Others also concluded that the external gamma radiation fields associated with uranium mining did not result in significant worker exposures (Federal Radiation Council, 1967; Simpson, S.D. [et al], 1959) Gamma exposure levels in most modern-day Canadian uranium mines are reported to be low with average annual exposures estimated to be less than 1 rem/a (Frost, S.E. [et al], 1981). However, two developments are taking place which affect the potential significance of external radiation fields in the uranium mining environment. The first development stems from the most recent system of dose limitation developed by the ICRP which is intended to limit the workers' overall risk from exposure to ionizing radiation through the adoption of a sum rule (ICRP 26, 1977) which combines external and internal radiation exposures. In the case of exposure to radon daughters the sum rule will have the effect of reducing the annual exposure limit below the recommended limit by an amount that depends on external radiation and other sources of internal exposure such as the inhalation of ore dust (ICRP 1980). The Atomic Energy Control Board of Canada (AECB) is reviewing this subject and is expected to produce its recommendations shortly. Irrespective of the form of the sum rule eventually adopted by the AECB, it is clear that the net effect of the sum rule will be a collective reduction of the individual dose limits for individual exposure pathways. The second factor is the increasing development of high grade uranium deposits in Northern Saskatchewan. Some of these ore bodies have an average ore grade of 1% to 5% U308 or greater. Since the potential external radiation fields increase in proportion to the ore grade, it is apparent that increased effort in radiation protection planning is required in order to develop safe yet workable methods for mining and milling such ores. This paper is intended to provide information which can be of assistance in the formulation and development of a mining and milling plan. The principal focus of the paper is source identification and the design of radiation protection measures to limit external gamma radiation exposure. The exposure of workers to external beta radiation fields is also discussed. The paper is organized as follows: - Section 2 deals with source characterization. - Section 3 discusses the effects of finite source size and distance (i.e. geometry effects). - Section 4 presents selected data that are useful in evaluating shielding requirements. - Section 5 discusses the potential beta radiation fields. - Section 6 discusses practical data requirements for worker exposure scenarios. - Section 7 presents a variety of work exposure calculations. - Section 8 is a summary of this paper. 2. SOURCE CHARACTERIZATION This section develops the basic formulae for estimating the fluxes and doses from external gamma radiation. The calculation of the radiation flux due to a distributed source (i.e. a linear, area or volume source) as a function of distance assumes that any distributed source can be treated as a summation of point sources. [ ] Uranium ore contains radionuclides from both the decay chains of U-238 and U-235. In this paper the radioactive daughters are assumed to be in secular equilibrium with the uranium parent. (If natural thorium were present in the ore in significant quantities, the gamma rays originating from Th-232 would have to be added to the gamma rays from the uranium series). In all, there are over 50 separate gamma rays (as well as alpha and beta particles) emitted from the U-238 and U-235 radioactive decay series (USHEW 1970). The total

Jan 1, 1981

By H. Hoberg, M. Langen, B. Hamacher

Since the term "abandoned hazardous sites" was first coined in the 1978 environmental report of the Council of Environmental Specialists, a number of different types of technology has been developed in the Federal Republic of Germany for the remediation of contaminated soils /l/. At former sites of the mining industry, such as metallurgical and coking plants whose soil has been contaminated by organic and inorganic pollutants over decades of industrial activity, there is an exceeding necessity for soil remediation. Also, many former locations of metal processing works, battery factories or scrap yards have been contaminated in particular by heavy metals. Wet mechanical soil decontamination has proven successful over the past 10-15 years in the purification of these soils The process goal is the enrichment of the pollutants in certain plant products and the separation of a pollutant concentrate from the decontaminated soil. Table 1 lists the steps of the highly advanced wet mechanical soil decontamination process to achieve this process goal. Table 1 lists both the name of each process step and its goal in terms of a direct separation of the pollutant or the preparation of the soil for subsequent separation steps. For the separation of heavy metals, density sorting and separation techniques utilising flotation were specifically used. The use of chemical auxiliaries such as acids and lye is limited to special cases because these in themselves produce additional environmental impact and the economical effficiency of these techniques compared to conventional methods is lowered by supplementary process steps for water purification. The subject of this presentation is to consider how soil decontamination processes can be effectively improved through a description of the material properties of soils contaminated by heavy metals, and through carrying out basic investigations about the adsorption of heavy metals. Soils of different origins, especially those from former mining and metallurgical sites, were used for the experiments.

Jan 1, 1995

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner's vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By T. Panhorst

Evaluation of through-deck blasthole sample reliability at the Lone Tree gold mine revealed a non-systematic bias in the sampling system. Ore is primarily hosted within the Powerline fault zone. Clay gouge, present in the fault zone and typically enriched in gold content, forms agglomerates during blasthole drilling leading to a segregation error during sampling. Replicated samples split from blasthole cuttings piles show through-deck samples to be either significantly enriched or depleted by 1.5 standard deviations or more from the mean gold content of their respective cuttings pile quality of through-deck samples correlates strongly with quantity of clay present.

Jan 1, 1999

By Neilson Rudd

Many deep well waste disposal. operations have adopted the technology of the petroleum industry but fail to make full use of the knowledge and experience upon which this technology is based. Inexperience in subsurface exploration commonly leads industrial personnel to an over simplified understanding of the complex subsurface rock/fluid environment and overly optimistic "degree of exploration /adequacy of knowledge" ratios. Several fundamental differences between disposal and petroleum production are discussed. In particular, the evolution of understanding of the subsurface in relation to degree of exploration is demonstrated by summarized case histories of such other forms of subsurface fluid exploitation as oil pro¬duction and underground gas storage, tracing subsurface interpretations from the initial exploratory concept to that of fullest development. Evolutionary changes in interpretation and their significance as applied to deep well disposal are stressed.

Jan 1, 1971

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By D. J. Torpy

With copper at its host depressed price in several years, producers are looking at every opportunity to cut costs in order to continue operating. Some of the measures that have been applied by different companies include reduction in manpower, high grading, and in some cases partial shutdowns. The most beneficial cost cutting measure implemented by Southern Peru Copper Corporation was to steepen the slope of the final pit limit from a conservative 37 degrees to an average of 48 degrees. By doing so, substantial cash outlays were saved. Southern Peru Copper Corporation (SPCC) operates two open pit copper mines and concentrators in the southern part of Peru, about 150 kilometers from the Chilean bordar. The Toquepala Mine went into production in 1960 and the Cuajone Mine in 1976. Both mines use shovel, truck and train operations. The trains, which haul ore to the crusher or waste to the dumps, are loaded either directly by shovels or by a transfer system. The Toquepala Concentrator treats an average of 43,000 tons per day and the Cuajone Concentrator an average of 55,000 tons per day. Concentrates are shipped via a 200 kilometer railroad to the port city of Ilo where the SPCC smelter is located. The annual production in the smelter from both mines is 290,000 tons of blister copper.

Jan 1, 1987

By A. D. Rovig

Metallurgical evaluation of autogenous grinding of Anaconda's Berkeley Pit ores indicated that tonnage throughput increases, at a finer flotation feed size, were possible by converting autogenaus mills to steel ball mills. In addition, initial test work showed that the improved grind resulted in slight recovery gains in subsequent flotation processing.

Jan 1, 1974

By Randall J. Weege

Nickel laterites throughout the world are similar in their gross aspects, but vary significantly in detail. The deposits occur in two separate and distinct geologic settings --those formed over ultramafic rocks which were mechanically emplaced, and those formed over ultramafic rocks that were intruded as melts. The source of the primary nickel in the parent rock may occur both as ionic replacement in silicate lattices and as nickel sulfides. Factors controlling the degree of laterization and nickel enrichment are dependent upon the parent rock characteristics as well as chemical and climatic conditions. Two chemically and physically distinct zones (oxide and saprolite) are commonly present in the laterized rock, but one or the other may be extremely thin or absent. Cobalt and copper may be present in recoverable amounts. Geologic, geophysical and geochemical methods are all utilized in exploring for these deposits. These methods are compared, evaluated and illustrated in the paper. Drilling patterns and ore reserve calculations are also discussed. In contrast to many ore deposits, processing costs are much higher than mining costs. The most efficient processing method is directly dependent upon the chemical composition of the ore. This variation in the chemical and physical characteristics of nickel laterites requires a detailed test program of the metallurgical response to representative samples and blends of ore. Detailed laboratory and bench-scale metallurgical tests are necessary prior to a full scale pilot plant test.

Jan 1, 1978

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By H. G. Kok

The concept of mobile crushers is not new. Since their introduction about twenty-five years ago, mobile crushers have continued to gain widespread attention. Mobile crushers reduce minerals in the open pit mine to sizes which can be transported by belt conveyors thereby reducing or eliminating the need for truck haulage. Truck haulage is costly, often representing as much as 50% of the total mining cost. More than 80% of the cost of truck haulage is for fuel and lubricants, tire replacements, and operators' wages, and it can be anticipated that the cost of these items will continue to increase at a steady pace. Compared to truck haulage, transportation by belt conveyor is more energy-efficient, less labor-intensive, and less subject to inflation. Therefore, mobile crushers, used in conjunction with belt conveyor systems, offer one of the most effective available methods of reducing energy consumption and mining costs,

Jan 1, 1980

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By H. W. Judges

A 16.5-kt/day underground molybdenum mine is being developed at Questa in Northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. A gravity block caving method has been selected for mining the ore. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. The shafts are being sunk under contract and the conveyor decline is being driven by Molycorp. The driving of the decline began in February, 1979 with a 10-man mining class. By the first of May, enough men had been trained to begin a continuous operation and by March 1, 1980 the face had reached the 1500 m mark. The heading is being driven with trackless rubber-tired equipment using a three-boom drill jumbo, 2.7 m3 LHD units and 7.3 m3 trucks. Ground support has been by rock bolts and wire mesh, followed by Fibercrete. A 16.5-kt/d underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. The new $200-million underground project will revitalize mining and milling activity at Questa, where small scale underground mining first began in 1920. Large scale open-pit mining was initiated in 1965 but now, because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. The company expects full capacity - 9 Gg of molybdenum per year - to be reached in 1984.

Jan 1, 1980

By Julián Ortiz C., Clayton V. Deutsch

Indicator simulation allows specification of different continuity of high and low values through the use of grade thresholds. The sequential implementation of indicator simulation has been widely used, but the problem of order relation deviations remains a significant drawback. A new procedure for "Hierarchical Indicator Simulation" is introduced that avoids order relations and offers greater flexibility than the conventional sequential approach. The new implementation simulates all locations at the largest threshold and then considers decreasing thresholds in turn. All nodes with grades that are above the previous threshold are excluded from the domain of the current threshold and therefore, they are not used as conditioning data. The probability of being above or below the threshold is calculated using simple indicator kriging using all conditioning data in the domain, thus the covariance structure is preserved. The theoretical framework of this new approach is fully developed. Practical implementation details are discussed. Application to a copper deposit shows the advantages and drawbacks of the method. Finally, the possibility of incorporating multiple-point statistics is discussed.

Jan 1, 2002

By J. M. Rebstock

Recent re-classification of crystalline silica as a potential human carcinogen has resulted in a new limit of 0.1% free silica in bulk powdered minerals. Detection of silica at this level can be expected to severely challenge or exceed the capabilities of existing protocols for x-ray diffraction, the traditional method for free silica determination. Automated SEH-EOS analysis provides an attractive alternative method, with direct analysis of individual particles for the determination of the concentration of free silica, and a direct measurement of silica particle sizes. This paper will discuss automated SEH analytical procedures, sample preparation, and statistical considerations.

Jan 1, 1990