Search Documents

By J. S. Gardner, J. J. Zaluski

I. INTRODUCTION West Virginia has a long history of coal production.1 The state at one time led the nation in total coal production, while at the same time coal from West Virginia constituted one quarter of total U.S. coal production.2 In more recent years, however, West Virginia’s level of coal production has been reduced in comparison to that of other states due to the high relative cost of producing coal in the state.3 Another blow to the producers of coal in West Virginia is the action known as Bragg v. Robertson.4 In 1998 various individual plaintiffs, as well as a conservation group known as the West Virginia Highlands Conservancy, filed a civil action under a provision of the Surface Mining Control and Reclamation Act of 1977, Pub. L. No. 95-87, §522, 91 Stat. 445 (codified at 30 U.S.C. §§1201-1328) ("SMCRA" or the "Act") that allows declaratory and injunctive relief against state and federal officials for non-compliance with the Act.5 The plaintiffs generally claimed that the Director of the West Virginia Department of Environmental Protection ("WVDEP") had exhibited a pattern of violating mandatory non-discretionary duties under SMCRA and the West Virginia state regulatory program.6 These non-discretionary duties involved many areas of regulation, including water quality standards, disturbance of wetlands, hydrologic reclamation plans, Approximate Original Contour ("AOC") requirements and AOC variances, post-mining land uses, contemporaneous reclamation, and as explained later, the "buffer zone rule."7 In addition to these claims against WVDEP, the plaintiffs also alleged that certain individual members of the Army Corps of Engineers (the "Corps") had failed to carry out statutory duties under the Clean Water Act (the "CWA") and the National Environmental Policy Act ("NEPA").8 Generally, the complaint stated that the Corps did not have statutory authority under the CWA to regulate valley fills created for the purpose of the disposal of waste material, i.e., the overburden associated with mountain top mining.9 Alternatively, the plaintiffs claimed that even if the Corps could regulate valley fills, the Corps violated NEPA by issuing nationwide permits without required analysis. Finally, the plaintiffs asserted that the issuance of a nationwide permit for surface mining valley fills is unlawful.10

Jan 1, 2001

By Ralph Spickermann

UK Seabed Resources (UKSR) signed a manganese nodule exploration contract with the International Seabed Authority on 8 February 2013 for a 58,000 km2 tract on the eastern edge of the Clarion Clipperton Zone (CCZ). UKSR is a private company based in the United Kingdom and established primarily to develop the commercial potential of the CCZ deposits. This is the first of many anticipated regulatory, market and technical milestones that are requisite for (1) environmentally responsible commercial scale production of nodule derived metals and (2) generation of revenue through their sale in the global commodities market. This presentation will describe the progress made to date in this effort and an industry-based perspective on the tasks and challenges that may lie ahead.

Sep 1, 2014

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By Toby Mayo, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

The Zoro pegmatite project in east-central Manitoba occurs 20 km east of the historic mining town of Snow Lake. A composite sample (Master Comp) was prepared fromthree pegmatite zones within Zoro Dyke “D1” including the North, Central, and South Zones for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample crushed to ca. P80 of 600 μm to determine the overall mineral assemblage, liberation of spodumene, and assess the potential recovery of spodumene by flotation. XRD and QEMSCAN results show that the sample consists of spodumene (10.5%), quartz (29.3%), plagioclase (29.0%), K-feldspars (21.3%), micas (5.1%), tourmaline (2.9%), and Fe-Mn-phosphates (0.1%). Spodumene is well liberated (88%), but also forms complex particles (7%), and middlings with quartz (4%). Liberation of spodumene increases from 81 in the + 600 μm to 95%in the − 106 μm size fraction. Liberation of quartz, feldspars, and micas account for 89%, 94%, and 83%, respectively. Electron probe micro-analyses and LA-ICP-MS showed that the average Li concentration is 3.7% in spodumene, 2196 ppm in micas, 1001 ppm in tourmaline, and 115 ppm in K-feldspars. Thus, spodumene accounts for 96%, micas 2%, Fe-Mn phosphates 1%, and both K-feldspars and tourmaline for < 1% of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other than spodumene carriers. Heavy liquid separation was conducted on the Master Comp which was crushed to − 6.4 mm, while the − 600 μmfractionwas removed fromthis test. The coarse fraction − 6.4mm/+ 600 μmwas subjected to HLS tests with eight heavy liquid-specific gravity cut-points (2.65 to 3.10 g/cm3). HLS indicates that it is possible to produce a high-grade lithium concentrate (close to 6% Li2O) after the rejection of iron silicates with magnetic separation.

Sep 16, 2020

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from prototypes to production-ready applications, the operating performance of the haul road will become critical to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width. This will, therefore, generate potentially significant reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and its associated deterioration rate, is predictable and manageable, based on the materials used to construct the road and the maintenance interventions to be carried out on the road.This article presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined partly from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this article, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images that are analyzed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration.Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management and, although the quality of mine roads have probably"

Jan 1, 2015

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has&apos; been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

By Eugene Guccione

The US mining industry today is fighting for its existence. We are plagued by the shortage of materials, of equipment, of fuels, of capital, of manpower. If we solve those shortages, we are then frustrated in our attempts to open a new mine or, perish the thought, a new smelter. If we manage to make a profit, demagogues will accuse us of stealing from consumers; and, if we do not make a profit and have to shut down, the same demagogues will accuse us of creating unemployment. Meanwhile, in every aspect of our business - from research, exploration and development, to production, marketing and selling - we are hindered in every way by the bipartisan mismanagement and crippling controls of a government bureaucracy gone amok. We are fighting a war on every front. Some of you realize that ours is a war of ideas. In order to win, our industry must make its ideas heard. But to be heard, we must have something to say - which means: we must know our case logically and consistently, all the way down to essential principles. A principle is a primary truth applicable to a great number of instances. A principle is like a road map: it shows you all the possible alternatives for getting from where you are to where you want to go. Although practically everybody recognizes the usefulness of a map and the need to consult it to find the best way&apos; to get from one city to another, most people are not as careful in charting the course of their life, or the course of their industry, or the course of their nation. And so they act blindly, at random, by the whim of the moment, and get nowhere fast.

Jan 1, 1975

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

One of the most important processing engineering tools for designing mineral processing facilities is linear circuit analysis. This technique, originally conceived and developed by Meloy, Williams, and Fuerstenau nearly four decades ago, provides fundamental insights regarding how unit operations interact and respond when arranged in multi-stage processing circuits. Researchers have successfully utilized this tool to improve the operating performance of industrial processing circuits incorporating coal spirals, magnetic separators, mineral spirals, and eddy current separators. More recently, advanced versions of this tool have also been developed to provide a standardized framework for circuit mass balance calculations, to output exact analytical solutions to mass yield and value-based efficiency expressions, and to estimate uncertainty propagation in separation circuits. This article reviews the historical development of linear circuit analysis, describes how the technique has evolved to address more complex circuit design problems, and presents industrial case studies that highlight the importance of this process engineering tool.

By P. Burmeister, R. A. Errath, A. Sapin

Sag Mills are becoming bigger in size almost every year. Concentrator plants are also becoming larger with more SAG and Ball Mills units with Gearless Mill drives installed in one plant. In contradiction to this development, concentrator plants are being built in increasingly remote areas, where the power supply and network conditions are not necessarily covering the needs for the operation of such plants. This paper describes sources of harmonic distortions and possible approaches to solve this problem. It also illustrates the permissible tolerances in terms of commutation of power electronics, based on already realized installations. Furthermore it explains how, and with which measures, harmonic currents created by non-linear loads with SAG and Ball Mill drives can be handled, and how harmonic standards can be fulfilled accordingly. Finally, this paper gives an overview about the technical impact of a strong versus weak network, and the economic relationship between them.

Jan 1, 2001

By Dongjie Zhang, Shuxin Liu, Jianduo Wang

Broken rock mass and unreasonable stope structure parameters can cause excessive ore loss and dilution in sublevel caving; this is the main problem faced by caving mining in recent years. This paper proposes a stope structure parameter optimization method suitable for steeply inclined medium-thick broken ore bodies and evaluates the reliability and effectiveness through case studies. To solve the problem of large ore loss and dilution in the high-end wall sublevel caving method of Xilinhot fluorite mine, it is necessary to select proper stope structure parameters. Based on the theory of random media, an end-wall ore drawing experiment was carried out, and the bulk flow parameters needed to optimization of stope structure parameters were determined. In the experiment, it was found the draw-out body of high-end wall ore drawing showed a fine top and a thick bottom; the granular media had good fluidity. The reasonable caving step is determined to be 1.2 m instead of the 1.6 m originally used. Through the optimization experiment of the mining route position along the vein, the study found that the best route position is different with the ore body inclination. When the inclination angle of the ore body was 90°, the reasonable route was located in the center of the ore body. When the inclination angle of the ore body was between 85° and 90°, the route moved from the center of the ore body to the footwall at a rate of 22.5%. When the inclination angle of the ore body was between 80° and 85°, the route moved to the footwall at a rate of 54.8%. When the inclination angle of the ore body is not greater than 80°, the route should be arranged on the boundary of the footwall. Field application results showed the dilution rate reduced by 7.66% and the recovery rate increased by 7.31%. Field test results verify the effectiveness and applicability of the optimized stope structure, which corroborates the effectiveness and applicability of the optimized stope structure.

Mar 10, 2022

By J. Pascoe, J. H. van Laar, J. H. Marais, F. J. L. Matthee

Advanced measurement and verification (M&V) is a process where the impact of an energy initiative is determined in real time. Data prediction models can be used to predict and compare energy consumption with a predetermined baseline. Deeplevel mines can benefit from advanced M&V as the impact of operational changes can be identified in real time. Ultimately, this can ensure that informed decisions are made regarding energy management based on the impact and severity of the occurrence. Previous studies on advanced M&V do not account for operational changes to the model’s baseline. These changes can significantly impact the performance of both the mine and related activities. The aim of this study is to propose a method that can accurately predict the energy consumption of a deep-level mine regardless of operational changes. To achieve this objective, nine different data predictive modelling techniques were considered. The proposed method is based on the Moving Average (MA) modelling technique due to its simplicity, flexibility, and rapid development time. The coefficient of variation for the root mean square error (CV(RMSE)) was used to statistically analyse the modelling error. If the predictions exhibit an unsatisfactory CV(RMSE), the model dynamically adjusts to reduce the prediction error. The model was developed to adapt to operational changes in scenarios where the standard model becomes irrelevant. The method developed in this study was able to predict the future energy consumption of deep-level mines with an accuracy of 99%, improving the mine’s energy and finance management.

Dec 13, 2023

By R. C. Milici

The primary factors that determine the marketability of coal from various supply centers in the U.S. are coal quality and supply; i.e. low sulfur, moderate- to high- Btu coals have large market areas when compared to less expensive but poorer quality coals. Price is the major factor in the competitive marketing of similar coal products. Good quality, (moderate- to high- Btu, low sulfur) coals from the Powder River and central Appalachian basins are marketed over large areas of the country, and central Appalachian coal is widely distributed in foreign markets, primarily as coking coal. In contrast, poorer quality bituminous coal (low calorific value and/or high sulfur) from the Illinois Basin, northern Appalachian Basin, and lignite from the Gulf Coast is marketed in or near the States in which it was mined even though the price at the mines may be lower than mine prices for central Appalachian coal. Widespread distribution of sub-bituminous Powder River Basin coal is enhanced by its exceptionally low mining costs, which offsets transportation costs to distant markets.

Jan 1, 2001

By A. Kevin Beaton, Robert W. Laakso

The desire for dry passageways promotes the NATM as it provides a final support system most suitable for the installation of a waterproofing membrane. Waterproofing during construction is a cost effective way to enhance safety and function as well as increasing the life of an underground structure. The NATM approach utilizes the surrounding mass as an integral element of the "ringlike" support system. At the Pennsylvania Turnpike Commission Lehigh Tunnel No. 2 various rock classifications were determined to require support measures ranging from 2 to 12 inches of shotcrete along with spiling, wire mesh, deformed bar, lattice girders and rock bolts as needed. Field instrumentation and monitoring programmes are a key factor for the success of the NATM. When the support "shell" stabilizes smoothing shotcrete, waterproofing and a final liner can be placed.

Jan 1, 1991

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By Rodney K. Morrison

MARTA, The Metropolitan Atlanta Rapid Transit Authority, is building a 53 mile heavy rail transit system to serve the City of Atlanta. Phase A of the Rail System, consisting of approximately 14 miles of at-grade, aerial and subway construction is underway. Metropolitan Atlanta lies in the Piedmont Geologic province of Georgia and is underlain by rocks of essentially granitic and gneissic nature. The soils encountered are primarily silty sands which are in-place weathering products of the parent rock and exhibit their relic structure. In general, these materials have presented no unique construction problems other than those created-by proximity of manmade structures, local availability of ground water, and top of rock elevation. The subway sections of primary interest in this paper consist of hardrock and soft ground tunnels and extensive cut-and-cover sections. The cut-and-cover construction includes excavations as deep as 80 feet. Temporary support systems in these deep excavations consist of soldier pile-timber-lagging or soldier pile-tremie concrete (SPTC) walls with internal bracing or tiebacks. In shallow cut-and-cover sections, where right-of-way economics permitted, slopes were laid back partially or fully to reduce or eliminate the need for bracing systems. Dewatering systems were required in most open cut excavations. Due to the close proximity of utilities and existing structures to the MARTA

Jan 1, 1979

By Elisa Comis, Jeffrey Peterson, Yama Ebrahimi

Construction of the Northeast Boundary Tunnel (NEBT), the last leg of the Anacostia River Tunnel System on DC Water’s Clean Rivers Project, started in September 2018 and was completed in April 2021. The 26-foot-bore earth pressure balance (EPB) tunnel boring machine (TBM) mined 26,737 feet at elevations between 80 to 160 feet belowground. Approximately 55% of the tunnel was cut through lower predominantly coarse-grained facies identified as the Cretaceous Patuxent Formation (undifferentiated) (PTX), and the remainder was cut through upper predominantly overconsolidated fine-grained plastic material facies identified as the Cretaceous Patapsco/Arundel Formation (P/A). Mixed face conditions were encountered in the transition from the P/A to the PTX and vice versa. This paper reviews the performance of the TBM that mined the NEBT through several unique challenges, including 8,000 feet of tunneling under the heavily developed Rhode Island Avenue corridor, major sensitive structures, cast iron water distribution mains, and other sensitive utilities.

Dec 1, 2022

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007