Search Documents

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By Tim O’Neil

“America’s mining industry brings good jobs to communities across America and provides the energy, minerals and equipment that are vital to our economic security and our way of life.” That was the surprise videotaped greeting from President George Bush at the official opening ceremony of MINExpo 2004in the Las Vegas, NV Convention Center. Jack Gerard reinforced the upbeat mood at MIN-Expo. He praised Nevada Gov. Kenny Guinn for his support of the mining industry, the state’s largest manufacturing sector. Gerard is the president and chief executive officer of the National Mining Association, the sponsor of MINExpo 2004.

Jan 1, 2004

By Wayne N. Marchant

Introduction The issue of coal mining safety plays an important role in the United States' growing dependence on coal to supply its future needs. This article will address the federal government's role, principally the US Bureau of Mines, in meeting this challenging growth and demand while reducing the social and economic costs attributed to injuries and fatalities in underground mining. Some interesting facts and projections with respect to the nation's energy picture will be discussed. This includes the distribution of its reserves and the projected role of coal in the energy and economics of the nation's future. Underground mining will continue to be an important means of providing this coal. The author will discuss how the Bureau of Mines' research program addresses the problems of health and safety that grow out of the demand for more coal. Future projections First, a synopsis of salient facts and projections concerning the US's situation with respect to energy and the economy. Figure 1 depicts the relative quantities of recoverable energy reserves in the United States by their type. Most people are aware of the nation's use of oil. We hear a lot about natural gas. And we are aware of the controversy over the use of nuclear energy. But, while looking at Fig. 1, the question becomes, "Where will our fuel to meet the demand for energy in the future most certainly have to come from?" With 82% of the nation's recoverable fuel reserves being coal, the answer is irrefutable. Coal will be that source. Figure 2 is the present market for coal. It shows that 77% of the coal mined goes to supply electric utilities. Therefore, the coal industry as a whole is most sensitive to the trends and demands for electricity. It is less affected by what happens in other markets, such as export and direct industrial use. In fact, the coal industry is three times more sensitive to the electric utility market than to all other markets combined. Therefore, the trend in the demand for electricity must be examined. Electricity demand is expected to increase steadily over the next 15 years. It is projected to grow from its present 2.3 trillion kWh per year to 3.5 trillion kWh per year by the year 2000. The fuel to supply this increase in demand must come from somewhere. The question is "How much of this extra fuel will be coal?" Although the demand for electricity is predicted to increase, the demand for coal does not necessarily follow. Coal must maintain its fraction of the energy sources used for electricity generation if its demand is to increase at the same or greater rate as electricity. Except for a near-term dip in demand due to a slight increase in nuclear capacity, the domestic electric generation accruing to coal will go from 56% in 1985 to more than 60% in 2005. Thus, the predicted trend is for coal to become a larger part of the fuel mix for electric power generation. Similarly, looking at the most recent forecast for total coal consumption trends, it can be seen that for electric power generation alone, the coal industry must be able to supply an additional 316 Mt/a (348.5 million stpy) by the year 2000 (Fig. 3). It must be stressed here, though, that without significant improvements in mining safety, it can also be easily predicted that injuries and fatalities will increase in proportion to the increase in coal production. Will society consider that acceptable? This author does not believe so. Figure 4 examines the effect of coal prices on the price of electricity. The projections show that the already high proportion of fuel cost will become a greater fraction of the consumer price for electricity. Specifically in 1985, 36% of the price of electricity was the cost of the fuel. In 1995, 46% of the price of electricity will be the fuel cost. That implies that the price of coal will have an increasing influence on the consumer price for electricity. Thus, as coal is used more to generate electricity and as fuel becomes a greater

Jan 4, 1987

By S. C. Sun

Pennsylvania has ample reserves of high-alumina clays which are potential sources of alumina, but many of these clays contain large amounts of iron, which makes them unsuitable for treatment by acid processes(1). The purpose of this investigation was to determine the optimum conditions for the selective hydrochloric acid leaching of iron (2-4) prior to the sulfuric acid extraction of alumina from Pennsylvania ferruginous high-alumina clays. This was accomplished by first testing the iron-bearing minerals and the clay minerals most often encountered in Pennsylvania clays to determine their rate of dissolution in hydrochloric acid solutions. The results of individual minerals were then based for leaching Pennsylvania clays with a 19% hydrochloric acid solution at the boiling point of the acid for approximately 30 minutes to achieve as high as 90% iron removal and only 2-5% alumina losses.

Jan 1, 1968

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 3, 1985

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior ofTiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was 150 and that of the silica in the same system was 0.02, resulting in a separation factor of 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By A. J. Romeo

The Old Hickory heavy mineral ore body, which lies within the Fall Zone of south central Virginia, has been mined since 1997. There are many differences in this deposit when compared to humate-laden mineral sands mines of southern Georgia and Florida. These differences include an abundance of kaolin-rich clayey sands, highly concentrated and iron-colored heavy mineral sand units, and a base of mineralization that is undulating. For these reasons, the selective approach of dry mining with track excavators is ideal. Grade control in this deposit uses traditional panning techniques and requires an intimate working knowledge of near-by drilling data. Mine geologists train equipment operators to recognize the base of mineralization by such characteristics as a stark color change, significant changes in grain size, and/or considerable, recognizable shifts in the concentration of heavy minerals. The regular pattern of mine site drilling does not always prepare the geologist and digging crews for occurrences of near-vertical contacts between the saprolite basement and the ore sands. These deformed areas, combined with undulating and pinching ore zones, require close monitoring and flexibility by the geologist and the mine operators.

Jan 1, 2005

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By I. Demers

Doyon mine, Quebec, Canada evaluates the possibility of desulphurizing their tailings to produce material to be used in as cover over the acid generating tailings disposal site. Laboratory tests were conducted and showed that a single-layer cover made of desulphurized tailings placed over reactive tailings can prevent the generation of acid mine drainage. Modelling with the software Vadose/W was undertaken to optimize the design parameters, namely cover thickness, water table position, and residual sulphide content of desulphurized tailings following laboratory work. It was found that the optimal configuration includes a 1 m desulphurized tailings cover containing 0.8%S, with the water table kept at the interface between the reactive tailings and the cover. To maintain the cover performance to reduce oxygen flux towards acid-generating tailings even in the event of a long dry period, a sand layer is suggested to protect the cover from excessive evaporation. It is possible to reach the environmental objective chosen for Doyon mine (10 mol/m2/year) with the protective sand layer, even in extremely dry conditions.

Jan 1, 2008

By Lynn B. Hales

The Supervisory Computer System at Cities Service copper mine and concentrator at Miami, Arizona was installed at Pinto Valley in the spring of 1975. Design and specification [l] of the digital system was initiated jointly by key plant personnel at Pinto Valley and staff of Cities Service Research and Development Company. The Pinto Valley digital system [2] may be classified as a supervisory control system of hierarchical design. There are three fully independent satellite computers which retrieve and reduce the raw plant data from each of the three main operating areas - the primary crushing plant, the fine crushing plant, and the grinding and flotation plant. While the three satellite computers are core resident systems, the master computer is a disc-based operating system which also interfaces with a computer controlled on-stream x-ray analyzer system. Figure 1 illustrates the basic system configuration [3]. The software systems required to support a large system are quite diverse and vary greatly in function. The philosophy followed in dividing the software into three categories was designed to: 1) fully utilize existing process knowledge of technical staff; 2) delegate certain software tasks to outside sources already skilled and trained in software development; and 3) maintain final control over the design and operation of each system.

Jan 1, 1976

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By M. Maier

Geographic Information Systems (GIS) has evolved into a powerful tool for analyzing spatial and attribute data in many industries including mining. Modern field data collection techniques add another dimension to the use of data in the field and enhance the utilization of GIS for mining applications. This discussion will review how field data is collected and how office data and maps can be taken into the field to be analyzed and verified using pen-based computers and differentially corrected GPS.

Jan 1, 2001

By Roberto J. Guardia, Robert A. Robinson, John Wilkerson, Wick Haxton

Several candidate sites have been proposed for the Deep Underground Science and Engineering Laboratory (DUSEL), a facility that would provide over 2000 meters of overburden to screen out cosmic rays that would otherwise interfere with experiments. Types of anticipated experiments include: detection of dark matter and stellar neutrinos, and evaluation of deep microbial life forms. Engineering experiments might include more refined scanning devices to “see” rock defects ahead of tunneling, improved predictive models for groundwater inflows and tunnel support requirements, and improved instrumentation for monitoring in-situ stresses, rock deformations, and pore water pressures. Spin-offs from this research might include more sensitive security detectors for scrutinizing shipping containers, new drugs based on new microbes, and improved sensor systems for tunneling. A site near Leavenworth, WA, was assessed and shown to have numerous topographic and geotechnical advantages. Rock cover is on the order of 2250 meters. The granitic bedrock is suitable for tunneling a variety of large underground openings.

Jan 1, 2005

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill?s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.

Jan 1, 2009

By C. Arthur Lefler

The hydrometallurgical processes for recovery of gold and silver in use at Round Mountain, Nevada and the practical aspects of the operation are discussed. Included are heap leaching by cyanidation, upgrading of solutions by adsorption of values on activated carbon and desorption (stripping) for electrowinning and subsequent refining steps to produce dore metal.

Jan 1, 1981

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987