Search Documents

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By W. Zhu

ABSTRACT: This paper presents further developments of the principle of Construction Process Mechanics of rockmasses, The principle of loading variations analyses in space-time is systematically described. To demonstrate the applicability of the theory and method, the effect of the construction process of two practical engineering cases are analysed. ZUSAMMENFASSUNG: Das Mechaniksprinzip vom Konstruktionsprozess des Massenfels wird in diesem Aufsatz weiter Entwickelt.. Das Prinzip von Variationsladungsanalyse mit dem Zeit-Raumseffekt wird systematisch erklaert. Um die Anwendungsmoeglichkeit der Theorie und der Methode zu anschaulich darstellen, das Mechanikseffekt des Konstruktionsprozess wird fuer zwei praktische Anwendungsbeispielen zergliedert. : RESUME: Dans ce papier le development se fait pour principles de la mechanique de process de construction . Le principle de variable analyse considerant effet de temps et de Space est present ´e . Pour demonstrer l´appilicabilite de le theorie et la methode , l´èffect de processe de construction pour ce deax examples sont analysés .

Jan 1, 2003

By S. Achilleoudes

This paper describes the various factors that contribute to the maximum design pressures acting on box fronts and how these factors influence the mass and economy of box front steelwork. The influence of material density, rock size and moisture content on the incidence of hang ups and mud rushes in the rock pass is also highlighted. The loads acting on any box front are a function of several different parameters. These include natural, operational and excavational parameters. A case study analysis was carried out using UG2 ore and a typical box front structure to demonstrate the relationship between the mass of the box front and the material pressures resulting from variations in the above parameters. Based on the results of this case study, the required design mass of a side mounted box front for a rock pass containing platinumUG2 increases in (close to) linear proportion to % overbreak and is also linearly proportional to the pressure on the face of the box front beyond saturated conditions. The mass of the box front structure also doubles with a 100%increase in over-break which emphasises that a box hole excavation that is as neat as possible will yield a lighter and more econimical box front structure.

Jan 1, 2005

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African platinum group metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky Reef is low in chromium and does not pose significant melting problems. Concentrates from the UG-2reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8?10-9bar at temperatures of 1550°C to 1600°C). During the converting process, care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation of Fe2NiO4 (trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever-increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3.A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Keywords: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium

Jan 1, 2004

By T. D. Mailula

Paper written on project work carried out in partial fulfilment of M.Sc.(Chemical Engineering) degree Chromite and talc are two major gangue minerals in platinum bearing UG2 ore processed from the Bushveld Complex in South Africa. During flotation, talc is effectively depressed by the addition of depressants. Chromite, on the other hand, is considered to be hydrophilic, its recovery is believed to follow water recovery and therefore recovered by entrainment only. In certain cases it has been shown that chromite can be activated by the reagent suite and hence is made amenable to true flotation. The aim of the work was to investigate the effect of the addition of copper sulphate as an activator and the effect of the depressant type and dosage on the recovery of chromite. The results of these experiments showed that copper sulphate, at higher dosages, activated the chromite. Low dosages of copper sulphate resulted in no chromite activation. This was observed at low depressant dosages of both IMP4 (guar gum) and KU5 (carboxymethyl cellulose (CMC)). When the depressant dosages were increased, at higher copper sulphate dosages, it was observed that the activated chromite was depressed by IMP4, but that the activation was still significant with the use of KU5. The activation of the chromite is attributed to the form of the copper species present in the solution and on the mineral surfaces at pH = 9 enhancing collector adsorption and thereby increasing hydrophobicity. These species were not measured directly and it is recommended that this should be further investigated using surface mineral techniques. Keywords: flotation; depressants; chromite; copper sulphate

Jan 1, 2003

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By J. Kirsch

Keywords: Pyrometallurgy, pneumatic transport, pneumatic transport Dense-phase pneumatic injection has begun to replace more traditional furnace-feeding systems. The paper describes the technology as it is applied to processes where the back pressure at the point of injection is greater than 50 kPaG. It reviews earlier systems of injection and more recent developments that address concerns for instantaneous control in modern smelters. The new technologies fall into two groups, (1) modified pressure-difference control (sub-divided into simple and complex) and (2) mechanical-feeder-based control. Features of current injection systems include feed splitting in two forms, passive and active, and co-current injection.

Jan 1, 2006

By D. O’Connor, A. Pytlik, D. J. Corbett

The resistance of yielding rockbolts to multiple impact loads was tested by means of a drop hammer. The methodology was based on the ASTM D7401-08 standard as well as the requirements specified for rockbolts by Luossavaara-Kiirunavaara Aktiebolag (LKAB – a Swedish mining company) and the Safety In Mines Research Advisory Committee of South Africa (project number GAP 423). During the tests, the loading force and bolt elongation were measured with a sampling frequency of fs = 19.2 kHz. In order to analyse the phenomena involved, the tests were recorded using two independent high-speed video cameras (600 and 1000 frames per second) and one thermal camera (128 frames per second). The tests demonstrated that all the samples transferred double the gravitational potential energy of Ep = 50.85 kJ from the impact load of mass m = 2825 kg and impact velocity of v = 6.0 m/s without failure. Damage to the bolt-resin contact in the upper anchoring zone of the bolt in the steel tube occurred after subsequent impacts. As a result, the macro-deformed bolt exhibits additional yield, and its operation following the shearing of the resin bond is similar to that of a ‘cone bolt’. Only one test resulted in damage to the threaded bolt rod-nut coupling, during the fourth impact; however, no damage to the bolt-resin contact zone was observed.

Nov 6, 2023

Mining is an inherently risky business; from the technical, environmental, social, and economic uncertainties associated with advancing an exploration prospect to a viable project to the operating, market, and safety risks and uncertainties attached to a developed mine. Since we cannot totally escape the risk and uncertainty related to resource projects, as an industry we should improve our presentation of the upside and downside risks in the context of the project?s development path and maturity. More transparent, consistent, and balanced views of technical confidence will better inform both internal and external stakeholders about the expected risk in the project. International reporting codes set out the minimum standards, recommendations, and guidelines for public reporting of Exploration Results, Mineral Resources, and Mineral Reserves. However, the reporting code principles of transparency and materiality are largely subject to the interpretation of the competent person(s), which may introduce a degree of subjectivity in reporting, particularly the level of disclosure regarding supporting information. It is fundamental that Mineral Resources, Mineral Reserves, and study outcomes are reported so as to unambiguously present the level of inherent technical uncertainty (or confidence) in a project, while conveying a balanced view of the opportunities a project presents. Reporting needs to consider various stakeholders who may rely on this information, and present the data in the context of the changing risk profile associated with project development paths and project maturity. This paper discusses the interdependence of resource-to-reserve conversion, the consideration of various technical-economic study types, and the level of confidence conveyed to stakeholders relying on these technical reports and other company public announcements.

Jan 1, 2014

The Modified Zincex® Process, developed by Técnicas Reunidas, is highly flexible dealing with a wide range of pregnant leach solutions. No matter if those solutions are produced from primary or secondary raw materials, and/or are based on conventional leaching, pressure leaching, heap leaching or bio leaching the result is always high-purity zinc product. The zinc solvent extraction unit within the process is a very effective barrier for impurities and a buffer for the composition of the pregnant liquor. This unit achieves an extremely pure aqueous extract that can be converted into different final products. All of them are characterized by fulfilling the highest purity standards. Also, there is the possibility to adapt the global process to a wide range of pregnant liquor compositions and various production capacities up to a zinc production limit over 150 000 t/a with a single solvent extraction plant.

Jan 1, 2002

By David J. Blackwell

The challenge; to design production facilities and in particular separation equipment which have the ability to deal effectively with the ever changing composition of well fluids, over the life time of the field in which it is operating, ensuring maximum uptime of the asset coupled with consistently effective separation. Design engineers are, however, continually confronted with a dilemma when selecting materials of construction for Oil/Gas separation equipment, since they are generally obliged to select an acceptable material of construction, based on ?predicted? operating conditions, at the lowest acceptable cost. Consequently many designs are somewhat basic and do not take into account the constantly varying dynamics of the well fluids being released into the separator. As oil fields mature, oil companies endeavour to maximize revenue by maintaining oil and gas throughputs. This often results in an associated increase in water and sand volumes and, in order to maintain efficient separation, an increase in operational temperature and pressure; subjecting the equipment to operational conditions for which it was never designed. In reality, therefore, the limitations and constraints placed upon new construction design often result in Maintenance Engineers having to solve the ensuing problems in difficult ?in-field? environments. Should refurbishment or upgrade be required then the status of the platform and that of the vessel during shutdown will dictate how this is achieved. Hotwork on the vessel is generally not preferred due to the requirement for post weld heat treatment and re-classification of the pressure vessel, not to mention the added risk in terms of safety. Unfortunately, until recently, there have been few alternatives to conventional ?hotwork? repair and protection systems, especially since the performance of cold curing polymer based repair and coating systems, for use in oil and gas process equipment, has, until recently, been limited by their resistance to temperature and pressure in immersed conditions. In line with the continued development of high temperature / high pressure oil and gas fields however, recent breakthroughs in polymer technology can now offer both repair and protection solutions which are able to function effectively at temperatures up to 180°C in immersed conditions combined with resistance to the destructive forces of explosive decompression from pressures in excess of 90 bar. This paper will look at recent work that has been undertaken to determine the suitability of modern polymer based repair and protection systems as an alternative to hotwork; thus enabling newly designed and upgraded internals to be cold bonded into position and further protected with temperature resistant coatings, in order to minimize the downtime of the asset and further to protect the vessel internals from the Erosive Corrosive environment.

Jan 1, 2006

By K. R. P. Petersen

Paper written on project work carried out in partial fulfilment of M.Sc. Eng.(Metallurgical Engineering) degree The interrelationship between mineral liberation and leaching behaviour of a gold ore is ill defined, mainly due to the complexity of both leaching and mineral liberation. This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organizing neural net, which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 8.1%). Moreover, the self-organizing maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2003

By P J. Grobler

The current commodity boom is depleting the ore bodies at a rate not seen in the past. As the existing ore bodies get depleted, only the more inferior bodies are left for exploitation. This places an emphasis on beneficiation to upgrade the lower grade ore to high-grade feedstock for downstream processes. This paper discusses the role of dense medium separation in this quest for high-grade feedstock for the future. It covers the production and utilization of ferrosilicon and gives a future perspective of the technology. It concludes about the way ahead and the challenges facing the processing fraternity and mining industry.

Jan 1, 2006

By R. M. Jara

This work evaluates and characterizes the impact of the support size and mining dilution of a block model in the operation and selection of equipment at an open pit mine. An exploratory analysis and geostatistical modelling of the grades assayed on a set of drill hole samples is performed, which allows constructing a grade model on a dense grid by means of a conditional simulation. The grades are then averaged to greater selective mining unit supports in order to proceed with the study and methodology. First, the metal-tonnage curves are used to analyse the loss of selectivity on the in situ resources caused by a change of support. Concerning the ore reserves and their mining sequence, defined in the pit optimization and analysis process, the same curves prove that the loss of selectivity is more accentuated. Second, the importance of the block boundary dilution produced during mining operations is assessed. Its value depends on the amount of ore in contact with waste, on the loading error of the equipment and on the ore loss/waste dilution criterion assumed by the planner. The dilution percentage and the differences between waste and ore grades become higher when the block size decreases. For these reasons, considering the dilution in the production plans makes mining a small support more constraining. An adequate delimitation of the orebody can improve the mining selectivity, leading to greater income. Finally, a study of the increase in mining cost that provides a zero difference in NPV between the different block size options is carried out, in order to determine the maximum increase in mining costs for which it remains profitable to mine at a smaller block size. Keywords: Mining selectivity, support effect, block boundary dilution, selective mining unit size, block model.

Jan 1, 2006

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003

By H. Saroglou

Anisotropy is a characteristic of intact foliated metamorphic rocks (slates, gneisses, phyllites, schists). Testing was used to establish the anisotropic behaviour of selected gneissic rocks. The effect of anisotropy on various mechanical properties (strength, deformation) and dynamic properties (wave velocity) was examined. The rock samples were also tested at successively higher confining pressures in order to evaluate the effect of anisotropic behaviour at high overburden pressures.

Jan 1, 2004

By P. N. Vernon

Ausmelt top entry submerged lance technology offers a cost-effective means of carrying out a range of base metal smelting operations with minimum impact on the environment. The system is capable of using a range of fuels depending upon local costs. Due to the intense, localised reaction zone, high energy efficiency is obtained and the physical size of the plant is relatively small compared to that of most competing technologies. Capital cost can thereby be minimised. The furnace is well enclosed, such that fugitive emissions and ingress of diluting air to the gas stream are both minimised. The oxygen potential in the slag can be varied over a wide range such that the system can be applied in both oxidising and reducing duties. Following a general description of the technology, the paper discusses Ausmelt plants already in operation. The application of the technology for the provision of additional smelting capacity, for the improvement of converting operations and for slag cleaning is then described. A brief explanation of how these processes could be applied at southern African smelters is given and the paper closes with an assessment of novel Ausmelt applications for this geographical region, such as zinc recovery from sulphides.

Jan 1, 1997

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005