Search Documents

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By Jochen Petersen, Thandazile Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques. The anodic dissolution process has been established to be a seven-electron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions. The number of electrons transferred in the carbonate and sulphate salts suggests that the sulphur is oxidised to a thiosulphate intermediate and the copper and iron released as Cu+ and Fe2+. The Cu+ and Fe2+ is subsequently oxidised in solution in non-Faradaic reactions. The deportment of Fe2+ and S2O32- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, however observations made on the mineral surface after leaching do not support the formation of elemental sulphur. Scanning electron microscopy and energy-dispersive spectroscopy analysis of the mineral surface suggest presence of an iron–sulphur surface layer completely free of copper under the ammonia–ammonium sulphate conditions, an iron-rich surface layer under ammonia–ammonium perchlorate solutions and absence of surface layer build up under ammonia–ammonium carbonate solutions. INTRODUCTION Hydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different approaches to hydrometallurgical treatment of chalcopyrite can be carried out. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base-metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilisation of copper(I) and copper (II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation 1 (Beckstead & Miller, 1977a):"

Jan 1, 2015

By T. Wettainen

Malmberget town is located in northern Sweden, approximately 70 km north of the Arctic Circle. Parts of the town overlie more than 20 iron orebodies, consisting mainly of magnetite with smaller quantities of haematite. The mine is operated by the mining company LKAB. Mining started in the 17th century, but not until the railway to the coastal city of Luleå was completed in 1888 did large-scale production commence. Around 1920, mining proceeded underground and today sublevel caving is the only mining method used. Sublevel caving causes subsidence of the ground surface, and buildings and residential areas have been relocated due to the mining activities for more than 50 years. The number of seismic events accompanied by strong ground vibrations is now increasing. In 2008 the mine received a permit from the Environmental Court of Sweden to increase production to 20 Mt of crude ore per year. A prerequisite for the permit was that the mine conducts a number of investigations regarding the environmental impact on the residents of Malmberget. One of these investigations concerned how seismicity will change as production increases and what measures could be taken to reduce inconvenience to the town residents. Today the mine possesses an extensive seismic monitoring system with more than 180 underground and surface geophones. For this study, eleven seismically active volumes in Malmberget mine were identified, and for each of them, a yearly future maximum magnitude interval was estimated based on the current production plan. Relationships between historical seismic events and measured ground vibrations in the town of Malmberget were established, and future ground vibrations caused by expected seismic events were estimated using a probabilistic approach. The outcome was the number of intervals of expected ground vibration per year and per monitoring point. Possible measures to reduce inconvenience for the town residents include blast restrictions, sequencing, and possibly preconditioning. The ultimate long-term solution is an almost complete relocation of Malmberget town. This process has recently been formalized and LKAB is taking an active part in realizing this goal.

Jan 1, 2014

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

By Klaus Hasselwander

Fluctuating SO2 gas streams represent a difficult task for designers of SO2 removal systems (with respect to designing the plant), but in spite of the designers great efforts to solve the problems, the operation of such plants requires much care and attention. A fluctuating gas flow usually results from metallurgical smelting processes. Both gas composition and gas flow rate may vary. The first part of this paper outlines some existing technical solutions and presents the Pros and Cons of the different solutions. These solutions outline are: - Sulphuric acid plants operated with a preheater permanent in operation - Sulphuric acid plants with concentration increase of SO2 gas either using regenerative SO2 removal or cryogenic partial condensation of the SO2 - Sulphuric acid plants with additional burning of sulfur to increase SO2 content - Single-stage sulphuric acid plants followed by a tail gas system (which is) designed for periods of low SO2 input In the second part, this paper describes some existing technical solutions for removal of SO2 at low concentrations (i. e. less than 0.1 - 2 %-by volume), which could be used as tail gas treatment system for acid plants. While selecting an appropriate solution, special attention should be given to operating costs, which usually to a large extend depends on the type of absorption agent and the costs for disposal of the sulfur compound produced.

Jan 1, 2009

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008

The gold concentration profiles which develop inside the activated carbon particles during the adsorption process were measured, so as to obtain additional direct proof of intra-particle mass transfer rate-control and to determine how individual carbon particles in a population vary in their gold uptake behaviour. The observed gold concentration profiles inside the activated carbon particles were typical of situations where an intra-particle mass transfer mechanism is rate-controlling. Gold di-cyanide penetrated the carbon particles with a wave-like front until it was uniformly distributed throughout the particle. This corresponds with the profiles predicted by the film and surface diffusion model. However, the rate with which gold di-cyanide was transported inside the individual carbon particles varied within the population of carbon particles. This variation was characterized by a lognormal distribution in surface diffusivity. Because the estimated variances of these surface diffusivity distributions were small, the dynamic adsorption behaviour of the carbons used in the present study did not deviate significantly from that predicted by a model based on film mass transfer and a single surface diffusivity. Van Deventer (1984, 1985 and 1986a) reported data that could not be adequately described by a model based on film mass transfer and a single surface diffusivity. In this study a model based on film mass transfer and a wide lognormal distribution of surface diffusivity values was applied to his data. It was shown that a population of carbon particles with a wide distribution in surface diffusivity values could offer an alternative explanation to the mechanism proposed by Van Deventer which was based on film mass transfer, with partitioning of the carbon into micro- and macropores with surface diffusion in the macropores and slow mass transfer into the micropores.

Jan 1, 1997

By J. Rogans

This paper discusses the comparative performances of the three activated carbon adsorption circuits at the West Wits operations of Anglogold. These circuits consist of two pump-cell circuits (at Two Plant, formerly Elandsrand and at Three plant) and a conventional counter-current adsorption circuit (at Mponeng plant). The implications of the improved performance of the pump-cell plants are discussed.

Jan 1, 2002

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

By J. O. Claassen

"A study conducted at 22 operating mines in the southern African region indicated that each mine employs about five management and improvement methods with roots in the manufacturing industry. All respondents reported the implementation of cost-saving initiatives, whereas 80% of the mines are affected by restructuring. TQM, Six Sigma, BPM, and TOC were found to be the most prevalent manufacturing management and improvement methods used. A mechanistic vs systemic evaluation of the suitability of these methods to bring about positive change in the industry suggested that complex, ever-changing mining systems are better served by a systemic flow-based approach, which is embedded in methods such as TOC, JIT, TPS, and Lean Production. These methods, however, lack industry presence, possibly because they do not effectively deal with the unique challenges associated with the mining environment. It is argued that successful mining business management and improvement depends on management’s ability to deal effectively with mining industry-specific requirements, the integration of the geologymining- plant system, and the implementation of systemic flow-based principles in all aspects of mining. IntroductionThe study aims to explore the use of manufacturing management and improvement methodologies in the southern African mining industry. Considering the unique challenges associated with mining operations, attention is given to the applicability of the most commonly used manufacturing methodologies in the tactical, operational, and strategic environments. The article endeavours to stimulate more research and debate in an unexplored field of study."

Jan 1, 2016

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson's effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson's effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By K. Collett

Elandsrand started shotcreting back in 1991. This paper will share the experiences of the mine by looking into the past, the present situation and the way Elandsrand plans to approach the future. It looks at the application of drycrete and discusses the factors that led to the introduction of wet fibre reinforced shotcrete. The logistical constraints of getting shotcrete material underground will be solved by the development of an underground batch plant, using run of mine waste rock as an aggregate.

Jan 1, 1998