Search Documents

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

By A. Ball

A fully instrumented laboratory drilling machine is described. It is designed to produce realistic drilling conditions with diamond microbits of 20 mm diameter. A computer-controlled data-logging system records the net power consumption, rotational velocity, bit thrust, torque, and penetration rate. Tests can be conducted under conditions of set thrust and rate of advance. In the tests reported, there is a significant correlation between the rock drilability and the measured rock properties of relative abrasion resistance and uniaxial compressive strength. Wear of a diamond bit is a crucial factor that cannot be determined simply from rock properties. Realistic drilability testing with appropriately scaled microbits is a convenient and economical way of evaluating diamond-bit performance and determining rock drilability.

Jan 1, 1990

By M. Reuter

This paper gives an overview of some criteria for the selection of processes for the recovery of lead and zinc from various raw materials and/or intermediate products. A glossary of possible processes and process variants, is presented and discussed, as well as the way in which these are interlinked. Recent developments in metallurgical process synthesis are also discussed, and the results produced by an eco-techno-.economic synthesis procedure for process routes in zinc metallurgy are given briefly. The way in which such a synthesis can complement a life-cycle assessment (LCA) of zinc-producing technologies is also described.

Jan 1, 1997

By A. P. Van Wyk, G. Pirnaar

The effect of vanadium on the susceptibilities of chromium and chromium-nickel steels to reversible temper embritlement was evaluated. The steels investigated were approximately equivalent to steels of as 970 Grade 708A42 and as 970 Grade 817M40, the major difference being that molybdenum had been replaced by vanadium in various concentrations. It was found that the vanadium had a detrimental effect and, in al the concentrations tested, enhanced the susceptibility to reversible temper embritlement of both the chromium and the chromium-nickel steel. The detrimental role played by vanadium in reversible temper embritlement is explained by a consideration of the effect of vanadium carbide, as well as of free vanadium, in solid solution in ferrite.

Jan 1, 1987

By E. J. Magri, R. M. Murray

This paper describes the application of linear programming to the monthly 'set up' planning of stopers' sections on two gold mines. On one of these mines, the purpose of the exercise was to maximize the total stoping production (measured in centares per month). On the other mine, the maximum stoping contribution (rands per month) was required. Maximization was to be achieved through improved planning, independently of the various other productivity improving activities that were taking place at the same time. The results to date show that, when linear programming is used, an average increase of about 9 per cent in stoping production (or contribution) can be obtained for these two mines.

Jan 1, 1978

By H. J. S. Kriek

Methods are described by which increased production is achieved whilst retaining full availability of equipment and decreased refractory cost. Refractory materials have certain limitations, and when these limitations are known the variables in operating practice having the greatest impact on refractory life can be controlled. The most important factors to be closely controlled are porosity, chemical constitution of refractory materials, slag basicity, slag volume, FeO content of slag and temperature at which the process is operated. Knowledge of the process is invaluable in deciding on the type of refractory to be used. The types of refractories used in and the operating variables of the ironmaking, steel making and steel finishing units are described.

By R. R. Mankowski

The work described here attempts to underscore the importance of the time lag between the end of a loading phase and the instant a winding drum begins its acceleration phase. Traces generated from a computer-simulation model show that the amplitude of the stress oscillations occurring in mine hoisting cable during the constant velocity-of-ascent phase is a direct result of the temporal sequence employed between the loading and the raising phases. While current and early literature indicates that extensive work has been undertaken on the isolated effects of these two independent sequences, the literature does not appear to contain any documented evidence to suggest an optimal control or interfacing between these two dynamic regimes.

Jan 1, 1995

This paper illustrates the application of numerical modeling methods, in conjunction with limit-equilibrium techniques, to the location of critical slip surfaces in slope-stability problems. Initially, the Spencer slice-based method of analysis is introduced, together with a dynamic-programming algorithm for slip-surface location. This limit-equilibrium method is assessed critically through the use of an illustrative problem. The technique is then extended to locate the critical slip surface for a similar slope, but with more complex constitutive and yield relationships for the material comprising the slope. To this end, the use of the stress field generated from a finite-difference program, together with a dynamic-programming search routine, is presented as an advanced technique of slope-stability analysis for engineers.

Jan 1, 1993

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976

By W. J. Murray

Tests were conducted during the middle of this year to evaluate techniques and the equipment used in a novel continuous mining system for use in narrow reef tabular orebodies. Equipment was designed and supplied to test a mechanized drilling rig, a selection of rock breaking techniques and an integrated rock removal system, mounted on a self-advancing reciprocating flight conveyer. As the rock breaking techniques do not depend on the use of large quantities of conventional explosive the systems and equipment employed here have the potential to run continuously for 24hours per day. Whilst the tests carried out use simple prototype equipment employing established technologies, the long-term objective remains the use of sophisticated machinery capable of running continuously and un-manned, only interrupted by brief service intervals. Keywords: Hydro-fracturing, Rock breaking, Low energy, Propellant, Non-explosive, Safety, Continuous mining, Rocksplitter, Boulder buster, Ro-bust.

Sep 1, 2001

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

By L. M. Falcon

Cassiterite is considered to be the only economically significant tin mineral in the earth's crust, and in its purest form has a tin content of 78,6 per cent. South Africa has limited deposits of the mineral, and by its exploitation contributes about 2 per cent of the world's production. This paper gives a brief history of tin mining in South Africa, which dates back almost 3000 years. Over the intervening years, many tin-mining operations have flourished and as quickly disappeared. At present there are only three tin mines in operation, and a description is given of the methods of mining, concentrating, and smelting that are used. The properties and uses of tin are listed, together with relevant statistics.

Jan 1, 1985

By C. O. Beale

This, the second and final part of a review on the subject(the first part was published in the March issue of this Jouma/), deals in detail with the 9 copper-producing companies in the Republic of South Africa. These are The Phosphate Development Corporation, Prieska Copper Mines (Pty) Ltd, Black Mountain Mineral Development Co. (Pty) Ltd, Rustenburg Platinum Holdings Ltd, Impala Platinum Holdings Ltd, Western Platinum Ltd, The O'okiep Copper Co. Ltd, Messina Ltd, and Palabora Mining Co. Ltd. The following are described for each company: background, development, geology, mining, concentration, and current situation. The last-mentioned company, being South Africa's largest producer, is dealt with in greatest detail.

Jan 1, 1985

By A. M. Thyer

Throughout the history of mining, underground fires or explosions have killed many hundreds or thousands of people. Fortunately, the safety record has gradually improved as a result of many people’s work on improving safety standards and work practices. However, fire and explosion still remains a threat in many situations. As a result the UK Mines Inspectorate commissioned a project to study materials used underground and to develop a fire/explosion risk assessment system. Such a system has been developed, following the study of incidents, specified fire resistance criteria, and fire safety practices. The final methodology uses a series of check sheets to identify potential fuels and ignition sources, preventative measures, fire/explosion mitigation systems, and items for inclusion in emergency plans.

Jan 1, 2003

By G. E. Blight

The load-compression characteristics of mine supports are usually evaluated by means of relatively rapid tests, whereas in the mine they are subjected to much slower strain-controlled compression. The effects of slow strain rates on the load-bearing properties of mine supports were explored by means of straincontrolled tests on model timber packs and timber-filled steel telescopic props. It is shown that the load-compression characteristics of these supports are considerably influenced by the rate at which they are compressed. The species of timber influences the behaviour, but to a relatively minor extent. Preloaded supports are shown to lose a significant proportion of their preload by relaxation.

Jan 1, 1978

By E. Adlard

This paper sketches an expert system for use underground in pinpointing problem areas in the operation of machines. The system is typically a software 'shell' designed to accommodate a series of 'if-then' rules that are intertinked to systematically search for the cause of the problem. During the search, the system asks a series of questions that have to be answered by the operator and then, when necessary, by an artisan. The rules of the system are generated by a knowledge engineer whose function it is to gather the necessary diagnostic information and prepare it in the required format for the expert system. Much still requires to be done in the development of such systems and in the testing of hardware to withstand the mining environment.

Jan 1, 1990

By A. Koursaris, Y. N. Turan

A series of experiments was caried out in a vacuum-induction furnace to investigate the solubility of nitrogen in stainless steel type 3100S. Melts were made under constant and variable partial pressures of nitrogen so that the absorption of nitrogen from the atmosphere could be examined. Additions of nitrogenized ferochromium were made to give high nitrogen contents in the steel. Nitrogen contents of up to 0,16 wt per cent were obtained under gaseous atmospheres. With additions of nitrogenized ferochromium, nitrogen contents of up to 0,525 wt per cent were obtained. Comparisons of the later value with existing data indicate that the equilibrium concentration of nitrogen was reached for the experimental conditions used.

Jan 1, 1992

By D. D. Marsden

This paper discusses the concentrations of sulphides and total sulphur in widely spread regions around mine residue deposits, from which rain-water run-of can enter the Vaal River system. Analyses of borehole samples from several deposits are used to establish typical sulphur head grades. It is shown that a high percentage of al the oxidizable, and hence leachable and pollution-causing, sulphur has already been removed. When the residues were fresh, water that came from the deposits was highly polluted, but the dissolved solids from these residues are today of very minor significance. The data are supported by analyses of the drainage streams.

Jan 1, 1986

By R. C. Hochreiter

The paper gives a technical review of the history, occurrence, mining, metallurgy, and end-uses of the platinum-group metals in South Africa, with most emphasis on platinum and palladium. The platinum industry has grown, from the first discovery of the metal in South Africa (in the central Transvaal) in 1923, to the present time, when the country is the largest producer of platinum 10the world, supplying almost 70 per cent of the platinum on the world market.

Jan 1, 1985

By J. M. Czaplicki

The problems connected with deep mine hoisting and the increasing complexity of this process can be analysed through the application of such mathematical tools as stochastic modelling to study the effectiveness, reliability or safety of hoist methods. To relate these theoretical investigations to real practice, knowledge about components, their stochastic nature and stochastic order of appearance is necessary. This paper presents results obtained during the ten-year (1976-85) period of research undertaken in the Polish mining industry by the Mining Mechanisation Institute of the Silesian Technical University, Gliwice, Poland.

Jan 1, 1987