Search Documents

By S. A. Ziebold

There is often a need to increase capacity through existing mist eliminator installations without significant tower modifications. Often there is not enough extra space outside existing vessels unless more expensive changes can be justified. Also, plant downtime must be considered. The challenge in retrofitting is to overcome velocity limitations inherent in the design while at the same time extend performance capability. The solution most often is to create new ways to add extra filter area while remaining constrained to the existing space. This strategy, however, can dangerously backfire if basic design principles are not followed. Mist eliminator design is a complex integration of many conflicting performance parameters. Often the objective is to increase scrubbing capacity while maximizing collection efficiency and service life and minimizing operating pressure drop (energy cost), particle regeneration (re-entrainment) and overall maintenance costs. Results of plant retrofitting using mesh pads, impaction fibre beds and diffusion fibre beds are presented based on actual plant projects. Often the retrofit project can be more effective by increasing the scope and combining other new plant equipment with the upgrade such as new tower components. In some cases, the type of mist eliminators can be upgraded from impaction type (velocity dependent) to Brownian diffusion type (velocity independent) if additional downstream protection or reduced emissions are desirable, especially at turndown rates. Trade-offs between different fibre bed types and styles are discussed as they relate to performance and maintenance.

Jan 1, 2007

By M. Viljoen

South Africa has produced more than a third of the total gold mined throughout history and remains a major although, until recently, no longer the largest producer of gold. South African gold production peaked in 1970 with an output of 1 000 t, a major component of the western world?s gold production, with the development of the country?s economy having been based largely on this mineral wealth. The costs and difficulties of increasingly deep-level mining, coupled with increasing labour costs and the low gold price until relatively recently, have seen production fall steadily since then, with the closure of many mines including those of the Central Rand Goldfield in the mid seventies. Thus in 1998, only 464 t were produced, with 342 tons being produced in 2004. In 2006, 275 tons of gold were produced and after more than 100 years was the last year as the world?s largest gold producer. In 2008 gold production was 221 tons, making South Africa the third largest gold producer after China (292 t) and the USA (234 t). Gold production would have been lower if it had not been for massive tailings dam retreatment operations that started in the late seventies, including in the Central Rand Goldfield. Mining of a remaining deep and lower grade shallow resources has now also become a major focus and has recently lead to a rebirth of reef mining on the Central Rand Goldfield.

Jan 1, 2009

By W. C. Joughin

A risk evaluation model has been developed, that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment. This enables the comparison of different support systems based on the expected frequency of injuries and the total cost of the support system, including the expected economic losses. The model takes into consideration the variability in joint orientations and joint strength within the geotechnical environment and the variability and quality of support systems. The quantification of the benefits of other rockfall risk-mitigating strategies, such as the effectiveness of barring or monitoring, are also incorporated in the model. The risk model is described in this paper and the validation of the model and case studies are described in Part II.

Jan 1, 2012

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By Neal Harries

The monitoring of rock slopes is a common procedure in the management of hazards associated with slope instability. Slope stability radar has become widely accepted as the state-of-the-art method for management of hazards associated with unstable slopes in open pit mines. This is confirmed by the rapid adoption of the technology since inception in mid 2003, with over 70 GroundProbe slope stability radars now in use at open pit operations throughout the World. The use of a monitoring system such as slope radar to identify slope hazards is only part of the solution to minimise the consequences associated with slope instability. The presence of the hazard must also be effectively communicated to the mine personnel, so that the correct response to the hazard can be enacted, and the risk mitigated to an acceptable level. In some surface mines, due to the geotechnical characteristics of the rock mass, hazards can develop rapidly; with slopes progressing from stability to ultimate collapse in just hours. In these situations, it is vital that efficient systems are developed to evacuate the area of the pit affected. Such a system has been developed by GroundProbe in South Africa, with the vital driving force for the project being provided by the Anglo Platinum Mogalakwena mine operation based at Mokopane. The mine based development of the system was perceived as an essential aspect in the development of the successful system. From an early stage, the mine provided essential input on both hardware and software developments to allow the system to be rapidly integrated into the mining operation. This paper describes the pit evacuation alarm system that was developed and discussed the benefits obtained from a mine based development program.

Jan 1, 2008

By N. B. Devi

The extraction of Cu(II) from HCl media using Cyanex 923 in kerosene was investigated. The effect of shaking time, aqueous phase acid concentration, extractant concentration, chloride ion concentration, various metal ions (Mn2+, Mg2+, Fe2+, and Ni2+), and temperature on the extraction were studied. Using 0.1 M Cyanex 923 the extraction of Cu(II) was 6.7 per cent from 3 M HCl, which increased up to 78.5 per cent with 6.5 M HCl and then decreased due to acid extraction by the extractant. The maximum extraction (97.5 per cent) was obtained with 1 M Cyanex 923 from 5 M HCl solution. A mathematical model has been developed to describe solvent extraction equllibria over wide ranges of concentration of extractant, acid, and chloride ions. The composition of the extracted species has been predicted on the basis of slope analysis results and extraction equilibrium modelling. The negative values of enthalpy change and entropy change confirm the exothermic formation of the extracted complex.

Jan 1, 2012

By D. J. Stanton

The objective of this study was to develop, install, and test a small underground mobile refrigeration plant (MRP) to deal with some of the real problems associated with mine cooling in an operating mine. The requirement for cooling the underground environment is discussed with particular emphasis on the need for this method of cooling, with the concomitant benefits. The research investigated current methods of cooling and reasons for previous failures in MRP. Both static and dynamic simulations were conducted to increase the confidence level under operating conditions. Implementation and testing, resulted in ?lessons learnt? requiring modifications, which are documented. Actual results have been recorded. These results have proved that significant cooling via MRP is feasible. Main benefits include positional efficiency, cost per kilowatt of cooling and cooling opportunities for remote hot areas of a mine. Finally, a proven technology is now available for large-scale implementation in the mining industry. Now the ventilation engineer has another system of cooling, which can be utilized in the quest to create an occupational environment, which meets the physical and mental health requirements of the worker.

Jan 1, 2004

By A. W. Sundström

This paper reviews the development and suitability of various important thermophysical and electrical properties with respect to base metal mattes. Areas of focus include the critical validation of measurements of viscosity, density, surface and interfacial tension, electrical conductivity, and an overview of the various experimental methods used to determine these properties. Accurate physical property data of mattes are critical in process modelling and computational fluid dynamic modelling of smelting and converting operations employed in the extraction of copper, nickel, cobalt and platinum group metals.

Jan 1, 2008

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By C. Musingwini, C. Beaumont

"Kansanshi mine, located in northwestern Zambia, uses conventional openpit mining to produce primarily copper, with gold as a by-product. The ore is extracted from a deposit with highly complex mineralogical suites that are difficult to process, sometimes leading to poor recoveries. The mine was using an ore classification system called ‘Mat-Type’, which classified various ore types into 22 different quality categories, ranging from poor to good quality. Ore with poor recovery was classified as ’poor quality’ ore and directed to long-term stockpiles. Due to a lack of proper integration between the technical and functional areas forming the mine value chain, Mat-Type unintentionally misclassified ore. A geometallurgical analysis was therefore undertaken to review Mat-Type and a new geometallurgical ore classification system, called ‘OXMAT ’, was developed to replace Mat- Type.When implemented, OXMAT eliminated nine of the 22 ore categories and the remaining 13 ore categories could now be more accurately and consistently defined, leading to a significant change in the quantity of ore being mined. OXMAT demonstrated that within a defined test volume of the geological model, waste tonnes could be reduced by 19% while ore tonnes could be increased by 17%. This paper therefore demonstrates the value created through integrated geometallurgical modelling. IntroductionKansanshi mine is located in northwestern Zambia, approximately 10 km north of the provincial capital Solwezi and about 160 km west of Nchanga mine in the Central African Copperbelt (Broughton and Hitzman, 2002). The location of Kansanshi mine relative to other major copper deposits in the Copperbelt is indicated in Figure 1.Kansanshi mine uses conventional openpit mining methods to exploit copper- and gold-bearing veins hosted in a structurallycontrolled mineral deposit. Mining is carried out in two areas of the deposit, the Northwest and Main pits. A third area of the deposit, called Southeast Dome, is currently not being exploited (Figure 2)."

Mar 1, 2019

By J. R. de Wet

The Skorpion Zinc Project demonstrated the viability of the production of zinc from non-sulphide (commonly called ?zinc-oxide?) ores, using the leach/solvent extraction/electrowinning process route. The success of Skorpion raised the profile of a number of other zinc oxide deposits, considered to be similar. However, a study of three such deposits demonstrates that the application of whole-ore-leaching may be limited and that the concentration of zinc, or at least the separation from acid-consuming gangue minerals, prior to leaching is essential to the successful recovery of zinc from these deposits. The recovery of zinc is dependent on an understanding of the geology of the deposit, the mineralogical association of zinc minerals with gangue minerals (Boni, 2005) and limitations of mining practice. Flowsheet development and the associated metallurgical testwork to derive an economically viable treatment route from two of these deposits are discussed. Key parameters affecting zinc recovery by gravity separation and flotation are presented, demonstrating that even minor differences in mineralogy have a profound impact on zinc recovery and reagent consumption. The study also deals with the determination of appropriate design parameters through metallurgical mapping of the dense media separation process.

Jan 1, 2008

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By C. Musingwini, T. C. Sebutsoe

"The primary objective of any mining business unit is to make profit by extracting, processing, and selling minerals from a particular mineral deposit. It is important to optimize extraction of the mineral resource given time, capital, and space constraints. Mineral extraction is often associated with uncertainty due to variable technical and human factors. Technical factors such as grade distribution, ground conditions, and equipment reliability influence the performance of a mining production system (MPS). The performance of the MPS is also impacted by human factors such as employee skills, health, and attendance. Uncertainty associated with technical and human factors often leads to actual output differing from what was planned. Therefore an in-depth analysis of the significant causes of deviations from the planned outcomes is relevant.In this paper we investigate the empirical relationships between inputs and outputs in a MPS in order to assist management in directing efforts at key production drivers. Once a MPS has been empirically characterized, more effort and resources can be focused on the key decision-making variables (DMVs) in order to meet the planned outcomes.For a typical underground, tabular, narrow-reef conventional drill-andblast platinum mine the face advance, face length mined, number of teams, team efficiencies, and team size have a statistically significant relationship with the centares (m²) produced, which is a key performance indicator (KPI). The production function derived in this study can be used to align the physical, technical, and human factors together to predict the optimal output level. The most significant production lever of the MPS is the face advance. IntroductionA mining production system (MPS) is a result of an iterative process of design, planning, and optimization of mining input variables and decision-making variables (DMVs). The MPS exists within the mineral extraction link of the complete mining value chain. It represents the stage where mining companies have the opportunity, through production, to start generating returns on the investments undertaken. Returns on shareholders’ investments can be realized at this stage."

Jan 1, 2017

By André Fouché

GFWW Bulk Sample Prep Plant INDEX ?Features ?Flow Diagram ?Pictures of Plant

Jan 1, 2005

By F. Smit

Mining and plant practices can benefit from preconcentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of preconcentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2013

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By V. Léveillé

As new legislation drives metallurgical plants to lower SO2 emissions, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost-effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an a mine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 by-product stream, which can then be directed to the front end of a sulphuric acid plant for conversion to sulphuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulphuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature, SO2 emissions in the treated gas can be controlled to as low as 55mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System, as well as which features and cost advantages for the treatment of smelter gases were important in the technology choice.

Jan 1, 2009

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By M. Verri

The paper describes the design options available for the simultaneous production of liquid sulphur dioxide, via cryogenic condensation, and sulphuric acid in a sulphur-burning sulphuric acid plant. The impact of the operating conditions of the cryogenic condensation on plant capital and operating costs are discussed, with the main focus on the optimization of the most important economic and operative drivers of the non-ferrous mining industry, such as energy efficiency, reliability, and availability. A case history relevant to an integrated sulphurburning plant producing liquid sulphur dioxide and sulphuric acid, recently started up in the Democratic Republic of Congo, is described. Keywords sulphur burning, sulphuric acid, liquid SO2, cryogenic SO2 condensation, liquid sulphur dioxide, sulphur dioxide.

Aug 1, 2013