Search Documents

By P. R. Jochens, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace by A. A. HEJJA,D. D. HOWAT, andP.R.jOCHENS Published in the Journal March 1973. DISCUSSION R. E. Leyman* The authors discuss in detail the effects of transport and storage at the steel plant on the reactivity of lime as measured by the DIN Reactivity Test. They attribute the deterioration in reactivity to the absorption of water vapour and carbon dioxide, but make no mention of the possible role of atmospheric sulphur dioxide in this respect. The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E FEATHER and G. M. KOEN Published in the Journal February 1973. AUTHORS' REPLY TO DISCUSSION (Published in the Journal July 1973) H. P. Carlisle Mr Carlisle's questions and observations will be dealt with in the same order as they were raised. 1. How were the mass percentages of the grains determined from the sizes measured in polished section?

Jan 3, 1973

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By Ralph H. Nafziger

This paper reviews the major deposits of lower-grade chromite in the world, and a wide variety of methods used for the recovery of chromium from them. Gangue materials in more coarsely sized ores can be separated by gravity means, whereas flotation techniques are required for finer-grained materials. However, unless there is considerable Iron In the ores, physical means cannot increase the Cr/Fe ratios. Chemical techniques such as hydrometallurgical methods, chlorination, roasting and leaching, and smelting are required for this purpose. A greater understanding of the physical properties of chromites and the chemical reactions that take place in the recovery operations is required before. the recoveries from lower-grade chromites can be maximized. More efficient recovery operations can be realized If It can be shown definitively that the reduction of chromites occurs via either a gas-solld or solid-solid mechanism, for example. The effects of specific impurities on the chromite reduction reactions need to be better understood, as do reagent and pH control in the flotation of chromite.

Jan 1, 1982

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By M. Loots, E. Van Der Lingen, S. Grobbelaar

The increased adoption of unmanned aerial vehicles (UAVs) may improve the productivity and costeffectiveness of remote sensing in the mining industry. This review’s objective is to enable stakeholders to identify possible application adoption, improvement, and innovation opportunities. The review merges a building block strategy and practical screening criteria to identify possible avenues of research to answer the review questions. After the screening process, 72 documents were included in the review. Papers were classified into four categories: exploration, development, exploitation, and reclamation. Fifteen applications were identified, the majority of which were in the exploration phase. The most often researched applications were topographic surveys, reclamation monitoring, and slope management. From the two UAV types identified, multi-rotor vehicles were the most favoured for all applications. From the eight remote sensing techniques identified, photogrammetry was the one most often used. Other techniques were limited because of complexity, cost, or the incompatibility of sensors and UAVs. The review was limited to published papers in academic journals. Future studies could aim to include empirical data on the latest UAV applications used in the mining industry.

Jul 2, 2022

By M. H. Moys

A method of estimating the percent solids in the discharge from a grinding mill is described and tested on both pilot and industrial scale. It involves the use of energy and mass balances around the mill discharge sump, requiring measurements of the flowrate and density from the sump together with temperatures of all streams flowing to and from the sump. Accurate estimates of the dynamic variation of mill discharge percent solids are made available, provided that occasional manual sampling of the stream is done to cope with drift in instrumentation. The use of a computer in this application was essential; the various advantages associated with its use are discussed. It is anticipated that this estimate of discharge density can be controlled at a set point by manipulation of the water fed to the mill, resulting in significant decreases in specific power consumption and media consumption.

Jan 1, 1987

By K. R. Vost

Most theoretical methods for the prediction of air-temperature gradients in underground airways always assume that the temperature of the entering air either remains constant or has only a slow seasonal variation. Large changes of temperature, caused by variations in atmospheric conditions on the surface, were measured in a fourteen-day period in air entering a horizontal airway. The changes in wet-bulb temperature were damped along the airway less uniformly than the dry-bulb changes; significant variations occurred in the wet-bulb temperature of the air leaving the airway. The damping was .associated with large variations in air-temperature gradients. Other causes of rapid changes In temperature are discussed. These changes must be taken into account in predictions of the frequency with which undesirable conditions can be exceeded at critical points in the ventilation circuit of a mine to allow proper planning of ventilation and refrigeration requirements.

Jan 1, 1977

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By C. van Loggerenbergt, P. E. Ventert

A strong incentive exists for the coal-preparation engineer to improve plant efficiency by modifying circuits and upgrading process equipment, since these result in lower production costs and more valuable plant products. At the Grootegeluk Coal Mine, it was found that the overall plant efficiency could be improved by modifications to the dense-medium circuits, the installation of additional process equipment for the recovery of fine coal, and improvement of the fine-material processing circuit. Apart from these modifications, there is still potential to increase the plant efficiency, particularly in the utilization of plant waste, the recovery of slimes, and even the improvement of cycloning performance as a result of new cyclone design. This paper points to the potential wealth locked up in existing coal-preparation plants, and shows how the coal-preparation engineer, with new technology at his disposal, can unlock this wealth.

Jan 1, 1992

By A. W. S. Schumann

G. H. HENDERSON INTRODUCTION It is a pleasure to have read Mr Schuman&apos;s wide ranging and highly informative paper and also to congratulate him. Before proceeding to give views on the use and preservation of coal in South Africa, it is perhaps apposite to look at the South African scene on the world canvas. Mr Schuman&apos;s figures in his Table I are highly revealing. The Table shows expected consumption, export and import demand in the year 1980 by the continents of the world. The Republic of South Africa is shown as one of only four exporting countries at that date, although in the interim, Australia has become an exporter and will continue to grow as an exporter of coal. Huge fields have been proved in recent years. There is reason to think that for some years, coal and its economical uses have been under-estimated. The importation of oil carries a constant question mark and the exciting possibilities expressed in the uses of Dranium a decade ago for power generation, appear to have met with some setback. Present indications are that breederreactors will be delayed until about 1990. The capital cost of such reactors, too, is enormous. By 1980 it has been estimated that 20 per cent of the energy required by the leading ten nations of the world will come from nuclear power, but 80 per cent would then remain for fossil fuels and hydro generation. COAL DEMAND AND USAGE It is of interest to record that coal production in all the countries of Europe has declined markedly in the last 25 years. This is due to competition from oil, gas and nuclear power and also for sociological reasons; but there are signs that efforts will be made to resuscitate, at least in some measure, the mining of coking coals for which there is a strong and growing demand. Possibly all hard coal now mined in Germany has coking properties and that country is self-sufficient in this commodity. Germany might perhaps consider selling coking coal to her neighbours and importing additional coal for power-raising purposes. It has been frequently stated in American publications that the coal reserves of the D.S.A. are sufficient for 1 000 years. What that means, I do not know, but it is at least an indication that America has huge reserves of coal. Domestic and export demand in the U.S.A. in 1968 exceeded production for the first time. In 1969, the United States&apos; output amounted to some 556 million tons, an increase of less than 2 per cent on the previous year. The output achieved fell short of demand, domestic and export, by more than 7 000 000 tons. This has caused and is continuing to cause anxiety in the U.S.A. In many countries young men for a number of reasons, largely environmental and social, are not coming forward in sufficient numbers for mining requirements and the same pattern has revealed itself in the Republic. This is, indeed, alarming because mining men in large numbers will be required to meet the estimated tonnage requirements set out in the following Table: It is difficult to visualise the replacement of these coal requirements either by oil or by nuclear fuels. The coal must be mined and men are required for the purpose. Unless a greater section of the population is allowed to participate in the more responsible aspects of mining, there is a serious likelihood that demand will not be matched by output. In addition to local demand, a lively export trade is possible. Exports are dependent on the future capacity of the South African Railways and Harbours and on Government policy. An export figure of 10000000 tons per year during the decade can be visualised and this figure would raise total estimated sales production to a figure of over 100 000 000 tons in 1980. At this point, it is necessary to examine the desirability or otherwise of exporting coal. How much coal

Jan 11, 1970

By N. Sinclair

"In open pit dozer bulk push operations, the material left resting against the highwall after blasting poses an issue. This is because dozers cannot physically get in behind the waste to begin the bulk pushing process. Instead, an excavator can be used to side-cast this waste for the dozers to access. An alternative technique is to have the dozers ‘side-cut’ the material, which involves the dozers running parallel to the wall, digging out the material, and eventually rotating their blades to begin bulk pushing. Industry practices suggest the latter technique is less productive and economical than using an excavator. However, such excavator sidecasting ‘economic viability’ assumes that smaller/ancillary type excavators are used (i.e. less than 23 m3 bucket capacity). So, what happens if some mine sites are restricted to using relatively larger excavators (> 23 m3 bucket) that are preferred for higher priority digging tasks? When can they avoid using their excavator? This paper explores multiple scenarios that have been designed and developed to simulate data results, which identify conditions in which the dozer side-cutting technique becomes more economically viable than excavator side-casting in terms of decreased unit cost per loose cubic metre. IntroductionOptimizing the cost of waste removal operations is important for the profitability of opencast coal mines. In the past decade, dozer bulk pushing has emerged and taken over from traditional waste removal operations such as dragline and truck-and-shovel methods at various sites around the world (Beatty, 1994). In a typical bulk push operation, once the bench has been blasted, waste is left resting against the highwall, which can either be cleared using a loading unit or by having the dozers ‘side-cut’ the highwall.Dozers perform most effectively when slot dozing side-by-side, perpendicular to the highwall. However, when dozers are required to remove material off the highwall, they must push parallel to the highwall, rather than perpendicular, hence ‘side-cutting’ the material to ensure a clean face. While dozer sidecutting is possible, it has been found that the majority of mine sites use a loading unit in this situation to avoid dozer inefficiency. Other perceived issues with dozer side-cutting include higher maintenance requirements and safety risks to dozer operators working in close proximity to the highwall."

Jan 1, 2019

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By J. Cilliers, R. Seitz, D. Drinkwater

Mineral processing produces a saleable product from high-cost ore. The Mineral Processing Engineer must constantly improve the separation to create the most value from the ore and reduce the associated costs. Graduate Metallurgists (or Chemical Engineers) have had the university theoretical training required, but often are illprepared to perform their plant roles. The in-work Metcelerate programme was designed specifically to develop the practical skills that Mineral Process Engineers require, by combining three key elements: 1. Knowledge transfer through self-paced, on-line training; 2. Practical skills acquisition through assessed, practical plant exercises; 3. Skills development through online tutorials. A final process improvement project adds significant value to the operation that far exceeds the training cost. Experience from Metcelerate clients has indicated improved staff retention, greater confidence, and pro-active process intervention.

Jan 1, 2023

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By C. Chibwe, M. Tadie

Copper electrowinning models are useful for prediction of process performance, optimisation and improved understanding of complex phenomena such as current distribution without the expense of physical experiments. Recently, finite element models such as those generated in COMSOL Multiphysics have been developed for the electrowinning process. The predictive capacity of these models is improved by incorporating physical and chemical phenomena. Since physicochemical properties of electrolytes can have a significant effect on the quality of copper produced, this work was conducted to investigate the effect of such properties on electrodeposition at varying levels of copper, sulphuric acid concentration, iron concentration and temperature, in the presence of a smoothing agent. Tests were conducted at conditions similar to those for industrial copper electrowinning. Mathematical correlations were developed for the following properties; density, conductivity and diffusivity which were compared to existing models in literature and thereafter applied in a COMSOL generated model. The model predicts, current distribution at the cathode surface, deposit thickness (morphology), concentration of species within the cell and current efficiency. Current distribution output shows the impact of several phenomena on the deposit generated including the relationship between increasing copper concentration and current density and lack of influence of acid concentration on this property. Keywords: Electrowinning, physicochemical properties, electrolyte composition, modelling

Jan 1, 2020

By S. Kirkpatrick, J. Mukendwa

"The mining operation at Namdeb’s Southern Coastal Mine (SCM) is unique. It targets gravel layers up to 30 m below sea level, which continue to dip deeper, further west, under the Atlantic Ocean. On this storm-dominated coastline, severe water seepage into mining areas, rugged orebody footwall characteristics, and highly variable resource grades all contribute to a challenging operational environment. Namdeb has a proud history of innovation, and as the mine progresses further westwards and associated technical and economic challenges increase, this innovative culture has become essential to the future of the mine. The Theory of Constraints (ToC) has been widely used at SCM, and across the mining discipline, to focus efforts on improving overall business profitability. Through analysis of the mining processes, opportunities were identified, solutions developed, and initiatives implemented with staggering results across all three mining disciplines, i.e. stripping, load and haul, and bedrock bulking and cleaning. This paper outlines the solutions adopted and the results of the ToC analysis. IntroductionSouthern Coastal Mine (SCM) is one of three Namdeb operations located in the southwestern corner of Namibia, between the Orange River in the south, the Namib Desert to the east and the Atlantic Ocean to the west (Figure 1). These three geographical features set the backdrop for the world’s greatest marine diamond mining placer (Badenhorst, 2003). SCM is situated along the coastline extending from the mouth of the Orange River to Chameis Bay approximately 120 km to the north. The active mining area, called Mining Area 1 (MA1) is, however, limited to very narrow strip, 30 km in length, in the south of the licence area, close to the town of Oranjemund.Namdeb, a wholly owned subsidiary of Namdeb Holdings, is a 50/50 joint venture between De Beers and the Government of Namibia. Diamonds were first discovered along the Namibian coastline in April 1908, close to the town of Luderitz, but mining operations started in the SCM mining area only in February 1929 (Schneider, 2009). Initially all Namdeb mining operations exploited massive land-based deposits, producing nearly 40 million carats from MA1 between 1920 and 1977 (Schneider, 2009) when mining targeted onshore raised beaches west of the high water line. Since 1977 however, SCM and Namdeb have developed a unique mining method to economically extract the resource which extends westward under the Atlantic Ocean."

Feb 1, 2019

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4, which is the main product, and other waste metal chlorides. TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amounts of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify the effects of using different feedstocks.

Jan 1, 2014

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023