Search Documents

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By S. C. Termes, P. E. Richardson, R. L. Wilfong

"The Bureau of Mines conducted research on the flocculation of various minerals with insoluble cross-linked starch xanthate (ISX) to determine its potential as a beneficiation technique for low-grade, highly disseminated ores and for selective desliming. Covellite, chalcocite, pyrite, pyrrhotite, chalcopyrite, bornite, sphalerite, galena, and molybdenite fines flocculate with ISX. Floc formation, floc size, and settling rate are dependent on pH, with the pH dependence differing for each mineral. Quartz is not flocculated by ISX. Experiments to obtain selective flocculation of sulfides from quartz were attempted. Good selectivity was only obtained for the bornite-quartz system. Post flocculation separations resulted in flocculated bornite in grades as high as 92 pct. Evidence is presented that the flocculation of many of the sulfide minerals with ISX may involve covalent bonding of the xanthate group to lattice metal site(s). INTRODUCTIONBecause of the increasing interest in selective flocculation as a beneficiation technique for low-grade, highly disseminated ores and for selective desliming, the Bureau of Mines has been investigating the flocculation behavior of several cross-linked starch derivatives containing chelating groups. This report dis cusses the flocculation of sulfide mineral fines by insoluble cross-linked starch xanthate (ISX).Polymeric materials such as ISX, which contain a chelating group of known re¬activity towards specific mineral surfaces, were first proposed by Slater, Clark, and Kitchener (1), 3 Kitchener (2), and Attia and Kitchener (3) as selective flocculants for mineral fines with particle aggregation possible through a bridging mechanism. ISX appeared to be attractive as a sulfide mineral flocculant because (1) alkyl xanthates are known to react selectively with sulfide minerals"

Jan 1, 1983

By T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±5% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Titan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 1, 1978

By Gerald W. Elger

This report compares the quality of zirconium metal prepared by batch reduction of zirconium tetrachloride by (1) sodium, (2) magnesium, and (3) mixtures of sodium and magnesium. Criteria for quality are based on chemical analyses and hardness testing of zirconium arc-melted from sponge. The best quality zirconium with respect to low oxygen content and hardness numbers was prepared by reaction of zirconium tetrachloride with a mixture of sodium and magnesium. It was found that this reaction could be successfully carried out by two methods: (1) addition of sodium and magnesium before the initial reaction and (2) periodic injection of sodium during reaction of zirconium tetrachloride with magnesium. The largest quantity of metal was found to be recovered from experiments in which a mixture of sodium and magnesium was used. Magnesium appeared to be a better reductant than sodium because magnesium-reduced zirconium contained less oxygen and exhibited lower hardness numbers than sodium-reduced metal.

Jan 1, 1962

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By Jonathan S. Kelly

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and the underground evaluation of ventilated cutting drums, on a double ended ranging drum shearer. The ventilated drum uses high pressure (1,500 psi) water sprays to draw air (3,500 cfm) through 12 airmoving tubes mounted in the drum hub. The sprays draw dusty air from the face side of the drum, scrub the air, and discharge the clean air on the gob side of the drum against a deflector plate. During a three week underground evaluation, the cutting drums reduced shearer generated dust levels at the shearer operators position by 40%, at the shield operators downwind of the shearer by 55%, and at the tailgate by 55%. Cutting and loading performance of the drums were superior to the mine?s conventional drums. After the evaluation, the mine continued to use the ventilated drums to finish mining the panel. During this 3 month period, there were no mechanical or seal failures demonstrating excellent system reliability.

Jan 1, 1987

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United Status. These data are presented in tabular form under the following headings; General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules, under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and. tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By G. D. Bakulev

Economic Importance of Gasification of Fuel and Brief Outline of Development of Underground Gasification of Coal in the U.S.S.R. The underground gasification of fuel offers a number of economic and social advantages, principally the following: 1. Full automation of labor-consuming coal-mining processes, which resist complex mechanization and automation, particularly shaft mining. 2. Elimination of hard, dangerous, and often unhealthful mining work. 3. Creation of hygienic conditions for personnel employed in gas production, as well as for those in boiler rooms using the gas. 4. Possibility of automation of complex production processes of thermal-electric powerplants using underground gas with economic installations for steam production. 5. Economic operation of thermal-electric powerplants constructed in the areas of underground-gas production. 6. Release of railroads from the burden of transporting fuel. 7. Extension of the power base of some areas in need of fuel and of the economy as a whole due to use of fuel deposits not amenable to normal mining practices. 8. Reduction of capital investments per unit of energy produced in the form of fuel. 9. Substantial increase in general labor productivity. 10. Possibility of substantial reduction in the cost of fuel produced and of electric power produced from underground gas.

Jan 1, 1962

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By M. I. Copeland

The investigation of the iron-gadolinium phase diagram is part of a project undertaken by the Bureau of Mines and sponsored by the Atomic Energy Commission to investigate rare-earth alloys. Data from the investigation of the iron-gadolinium phase diagram revealed a single eutectic system with very limited terminal solubility and three intermediate phases. The eutectic point occurs at about 85 percent gadolinium, and the eutectic isotherm, which occurs at 850° C., extends from the compound Fe2Gd to 99-plus percent gadolinium. Very little solubility of the solid phases in each other was observed. The three intermediate phases, FegGd, Fe3Gd, and FeaGd, melt incongruently at peritectic isotherms at 1,320°, 1,150°, and 1,080° C., respectively. The crystalline systems of the three phases were determined as follows: FegGd, hexagonal; Fe3Gd, hexagonal or rhombohedral; and FeaGd, face-centered cubic. No lowering or raising of the alpha-gamma iron transformation at 910° C., the gamma-delta iron transformation at 1,388° C., or the gadolinium transformation at 1,262° C. was observed. The principal methods used in determining the iron-gadolinium phase diagram were melting-point determinations, thermal analyses, metallographic examination, and X-ray diffraction analyses. Melting, heat treating, and thermal analyses were conducted in a vacuum or under a helium atmosphere because of the avidity with which oxygen combines with gadolinium at elevated temperatures. A few hardness values were determined, but they had no part in the derivation of the phase diagram. No other mechanical properties were determined.

Jan 1, 1962

By Charles Zahn

Direct mass spectrometric determination of alcohols in the presence of hydrocarbons has not been possible because of the similarity of hydrocarbon and alcohol mass spectra. Experiments have demonstrated that by converting the alcohols to their trimethylsilyl derivatives, characteristic mass spectra are obtained free of interference from hydrocarbon ion fragmentation. Hexa- methyldisilazane is the reagent selected for the conversion, An improved method of preparing the reagent is given, Mass spectrometric determination of alcohols as trimethylsilyl ethers now is not only possible without prior separation from other materials, but the range of the room-temperature mass spectrometer is also extended to include the C10 alcohol region. Water does not interfere because it is converted to hexamethyldisiloxane, which has its own distinctive mass spectral peak, Experience indicates that other compounds such as glycols, amines, and phenols probably could also be determined by mass spectrometry of their trimethylsilyl ethers. Studies on the similar detemination of phenols in coal oils have been started, When mass spectrometry is not available, gas-liquid chromatography of alcohols before and after their conversion to the trimethylsilyl derivatives probably could be performed. The preparation and properties of the trimethylsilyl derivatives of 23 alcohols, 2 glycols, 3 amines, and 1 mercaptan are detailed. INRODUCTION During investigations by the Bureau of Mines at the Pittsburgh Coal Research Center relative to the development of Fischer-Tropsch processes, complications were encountered in the mass spectrometric analysis of alcohols in hydrocarbon oils. The fragmentation peaks of the alcohols and the hydrocarbons were so similar that an accurate analysis was not possible, Since involved separation techniques are necessary to isolate alcohols from hydro-carbons for separate determinations, efforts were turned to the search for a

Jan 1, 1962

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By M. R. Geer

Information on the performance of coal-cleaning equipment is necessary to provide a basis for evaluating the performance of existing plants and projecting that of new plants. Performance data can contribute greatly to the wise selection and effective use of coal-washing equipment. The Bureau of Mines has published information on the performance of several commercial plants, as well as of some laboratory-scale equipment, 5 (2-9, 11, 12, 17-12, 21-25) from time to time for a number of years. A more intensive program to provide such information for all the principal types of cleaning equipment is underway. The present evaluation of table performance is part of this program.

Jan 1, 1962

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956