Search Documents

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973

By R. J. Matetic, J. S. Peterson, P. G. Kovalchik

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof-bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included using various combinations of rotational speeds and thrusts, using 2.54- and 3.49-mm- (1- and 1 3/8-in.-) diameter hexagonal and round drill steels, using vacuum and wet conditions and using drill media of differing compressive strengths. This paper details the affects of each of these variables on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By R. L. Kidd, T. H. Miller

"INTRODUCTION This paper is the seventh of a series of yearly reviews started in 1921 and pre¬sents information gathered in a cooperative investigation undertaken by the United States Bureau of Mines and the University of Utah. It is the purpose of this report to make available flotation—reagent consumption data and other milling information in such a manner as to be of value to the milling industry and to the manufacturer of flotation reagents.These data have been compiled from a survey of about 300 concentration plants in the United States. Much additional information has been obtained from the various offices of the United States Bureau of Mines. Many of the plants covered in the survey made complete reports of their operations, but others were apparently unable to supply this information in sufficient detail to meet the requirements of this report. As a result, some sections of the report are more complete than others. In general, however, the mill reports were much more complete than in previous years, and for the first time it has been possible to calculate average mill recoveries in the treatment of certain classes of ores. As in the past, every effort has been made to conceal individual plant operations.ACKNOWLEDGMENTSIt is realized that the publication of this information is possible only through the assistance of the mill operators, and the authors wish to express their appreciation of this cooperation. Thanks are also due the various field offices of the United States Bureau of Mines, division of mineral statistics, for assistance in collecting this information."

Aug 1, 1931

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By Wilford S. Wright, Harold E. Heide, Robert S. Sanford

"INTRODUCTION The United States production of tin has always been negligible, and domestic requirements have been met almost entirely by imports. The advent of war in Europe in 1939 brought a threat to our foreign source of supply, and steps were taken by Congress to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, the Bureau of Mines and Geological Survey conducted investigations of domestic tin deposits.An examination of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.H. B. Heide conducted a preliminary examination of lode and placer-tin deposits at Cape Mountain in 1942, which was followed in 1943 and 1944 by a program of exploration by churn drilling in the placer area and trenching and sampling the lode deposits.Placer tin, found at the head of Goodwin Gulch, Cape Creek, First Chance Creek, and Boulder Creek, indicates that the mineral was derived from the vicinity of lode cassiterite occurrences on Cape Mountain. Placer tin led to the discovery of at least one, cassiterite vein by the Geological Survey and the Bureau of Mines."

Dec 1, 1946

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By Gregory R. Wagner

The Program of Mine Safety and Health Research described in this document reflects the continuing commitment of the Spokane and Pittsburgh Research Laboratories to focus on the most important areas where research can make a difference in reducing risk and improving safety and health for miners. It is the first program of work conducted since Congress mandated closure of the former U. S. Bureau of Mines (USBM) in the Department of the Interior and supported integration of the health and safety research function of the former USBM into the National Institute for Occupational Safety and Health (NIOSH). Organizational changes made FY97 a challenging year of transition. Ongoing research was reviewed and revised to reflect the new, more limited, health and safety mandate of the research laboratories. The mining industry, mine worker representatives, and interested government agencies provided broad input to assure that the research performed would focus on the most critical safety and health problems confronting mining today and which are expected to be faced in the future. The two laboratories worked to evolve coordinated programs of safety and health research, each with a special focus. The work of the Spokane Research Laboratory is directed toward issues of special importance to the Western mining industry, particularly those safety hazards found in metal/nonmetal mining and surface mining. The work of the Pittsburgh Research Laboratory will continue to focus on Eastern mining, particularly underground coal mining. Traditional areas of expertise for understanding and preventing fires and explosions and for controlling the hazards of dust and noise will continue to reside in Pittsburgh. Each laboratory is developing new capabilities in the analysis of relevant safety and health information to assure that program priority-setting decisions are informed by the best available data. Recognizing the continuing importance of communicating the results of research to all who are capable of improving safety and health conditions in mining, each laboratory has developed an activity for information dissemination and coordination with stakeholders. In the midst of organizational self-examination and change, the research staff in Pittsburgh and Spokane have never wavered from their continuing commitment to conduct the highest quality scientific research-solution-oriented scientific work meant to reduce the risk of injury, disease, and death from occupational hazards in mining. The pages that follow give insight into some of the program activities and accomplishments from FY97. I hope you share my pride in the many accomplishments of the NIOSH mine safety and health research program during this year. This report comes at a time of increasing stability for the mine health and safety research program. The organizational changes in Spokane and Pittsburgh have been concluded, and NIOSH has succeeded in recruiting a new, permanent associate director for mining to lead this critically important national program. Congress has contributed to an optimistic future by providing expanded funding for NIOSH mining-related research for the next fiscal year. On a personal note, I greatly appreciate the opportunity I have had to serve as the NIOSH Acting Associate Director for Mining during this transitional year. The commitment and intelligence with which the mining research staff pursued their mission was matched by their patience and understanding in moving into a new organizational environment. All of us committed to improved safety and health for this Nation's miners owe them our respect and appreciation.

By A. J. Fejes

The purpose of this Bureau of Mines report is to provide mining industry personnel and regulatory authorities with a subsidence-reference list and annotated bibliography that will aid them in locating subsidence information and in developing their own subsidence information sources. Over 700 references are listed in the Bureau's subsidence information center bibliography; approximately 600 of these references were obtained for assessment. Of these 600 references, 167 were selected to be rated, categorized, and annotated. All literature referenced in this report was published prior to 1984. Table 1 is a cross - referenced index that classifies and rates selected references with respect to specific keywords. References are rated not on quality of content but rather on applicability to given subject areas. Appendix A is an annotated bibliography of the references listed in table 1 and provides further information of each article to aid the user in selecting articles for specific areas of subsidence technology. Appendix B is a copy of the subsidence information center bibliography.

Jan 1, 1985

By Alvin Schallis

The. problem of supplying enough magnesia for the American war effort has become highly important. Before hostilities began, only about two-thirds of our, require vents came from domestic sources; now they must supply almost all the magnesia we need. A further burden is placed upon our own supply by the fact that more and more magnesia is being required, not alone to pace the war tempo of general industrial activity, but also to replace chrome ore in refractories and to make magnesium metal. The domestic magnesite and brucite industry is equipping itself to satisfy much of this greater demand for magnesia, but the remainder must be obtained elsewhere. The principal sources of magnesia are magnesite, brucite, dolomite or high-magnesium limestone, natural brines, sea water, salt-works bitterns, magnesium silicates, and magnesium salts. Although dolomite is tae subject of this paper, it should be considered in perspective with all these highly competitive sources of magnesia.

Jan 1, 1943

Since early July, domestic producer listings in primary aluminum ingot have been at 53¢ per pound. Dealers, however, lowered their August quotes by 1.8¢-2¢ to 47.5¢-48¢ per pound. BITUMINOUS COAL AND LIGNITE -The wildcat strike of UMWA coal miners which began on June 23 in protest of cutbacks in medical benefits appears to have ended. According to the West Virginia Coal Association on September 7, 1977, all mines in West Virginia were back in operation on September 6 and again on September 7. The Kentucky Coal Association reported approximately 2,500 miners were on strike in eastern Kentucky on September 6, but there was full employment on September 7.

Jan 1, 1977

By George A. Burrell, G. W. Jones, Frank M. Seibert

In this bulletin, the style of Bulletin 42 has been closely followed. Much of the material is reprinted on the following pages in its original form, and changes have been made only where manifestly neces- St,ry. Laboratory methods have been brought up to date. Some types of apparatus described in Bulletin 42 have now become obsolete and newer designs are described instead. The authors hope that this bulletin will be of as much service as was Bulletin 42.

Jan 1, 1926

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By R. F. Selden

The material in this paper is intended simply, to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions on various phases of the subject have been published, a few of which (4, 20, 25, 88, 90)4/ have more or less extensive bibliographies of tie earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon. dioxide with perhaps sore methane) is quite apparent.

Jan 1, 1934

By R. F. Selder

The material in this paper is intended simply to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions of various phases of the subject have been published a few of which (4, 20, 25, 88, 90) have more or less extensive bibliographies of the earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon dioxide with perhaps sore methane) is quite apparent. The presence of small quantities of carbon dioxide can be attributed to oxidation of the carbonaceous matter exposed to the air. In the few cases in which this explanation is not sufficient, obviously the carbon dioxide must escape as such from the coal and neighboring strata.

Jan 1, 1934

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By G. L. Oldright, J. D. Sullivan, W. E. Keck

"An apparatus and procedure developed in the laboratory of the South-west Experiment Station of the Bureau of Mines are capable not only of determining the rate and volume of penetration of solutions into porous materials but also of determining the total volume of voids within particles of porous material, and the density. The method is applicable to ores, bricks, concretes, tiles, filter bottoms, or other porous materials of this nature. As will be made clear in the descriptive matter to follow, the method measures (a) the volume of voids within the porous materials and is not concerned with the interstitial space between the particles.Porous materials usually contain some large voids and also pores that are capillary in nature. To measure the total volume of voids in a sample it is necessary to replace the gas or gases within the voids with some liquid of known density. The large cavities can be filled quite readily, but under ordinary conditions a long time may be required to fill capillary pores. As many porous materials are of a decomposable nature it is necessary to evacuate the porous materials and then submerge them in a liquid of known density to bring about saturation in a short time. Then by the use of a hydrostatic balance the volume of porous material (solid itself) can be determined. To determine the volume of porous material plus voids it is necessary to coat the sample with some material, such s paraffin, which will prevent solution from entering the voids; then, by means of a hydrostatic balance, the volume of porous material plus voids is determined and by subtracting that of the porous material from this the volume of voids is ascertained. The rate of penetration of solutions can be determined either (a) by measuring the change in weight as the sample becomes saturated when immersed ni a liquid of know density, or (b) by measuring the volume of liquid penetrating with a dilatometer. In either instance, due to the fact that some penetration takes place as soon as the sample comes in contact with solution and before a reading can be taken, the sample must be paraffined to determine the total volume of penetration. Since many porous materials partly decompose and disintegrate in liquids the rate and volume of penetration can better be measured by dilatometer than by the change in weight, as saturation takes place when immersed in a liquid. The details of procedure for determining (a) total volume of voids, and (b) rate and volume of penetration are given in this paper."

Oct 1, 1930

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.