Search Documents

By Sabri Ergun

Previous studies of magnetic separation of pyrite from coals have been reviewed critically. Magnetic susceptibilities of United States coals of differing rank have been measured. The effects of crushing, magnetic mixing, drying, weathering, and heat treatment on the enhancement of the magnetism of pyrite have been analyzed. The importance of size distribution of pyrite in the coal and the necessity of crushing to liberate the pyrite has been discussed. It has been found that the inherent susceptibilities of the carbonaceous, mineral-free portions of coals (? -0.5 X 10-6 in cgs units) and of relatively pure pyrite isolated from coals (? -0.3 X 10-6) do not permit efficient separation of pyrite from coal; the average susceptibility of the magnetic fraction of coal must be raised to 3 X 10-6. Friction forces encountered in crushing sedimentary pyrite embedded in coal do not increase its susceptibility. Subsequent weathering or heat treatment below 400° C leads to the formation of iron sulfate and hence increases the effective paramagnetism of pyrite. Ferromagnetic compounds of iron are not formed in significant quantities at temperatures below 400° C. The degree of liberation and apparent susceptibility of pyrite are the most important parameters in its separation. It is concluded that effective beneficiation of coals can be achieved by magnetic separation. A sufficient increase in the susceptibility can be achieved by converting less than 0.1 percent of pyrite into ferromagnetic compounds of iron. Such conversions occur only at temperatures >500° C. An investigation of the dielectric properties of coals and pyrite in the frequency range 0.1 to 60 Mhz indicates that the imaginary dielectric constant of the pyrite is about 100 times larger than that of coal. Exploratory experiments indicate that pyrite can be selectively heated to temperatures above 500° C without appreciable rise in the temperature of coal. It appears that dielectric heating of coals in the Ghz frequency range is the most feasible method of enhancing the paramagnetism of pyrite.

Jan 1, 1968

In 2007, a total of 725 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Nonmetal mines com-prised 4.9% of all m ining operations. ? Mines producing common clay comprised 25.4% (n=184) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the U.S. Virgin Islands.

Aug 1, 2009

By Changwoo Lee, Jan M. Mutmansky

"This paper results from the research at The Pennsylvania State University into establishment of standard procedures for characterization of respirable coal dust performed by the Generic Mineral Technology Center for Respirable Dust and supported by the U.S. Bureau of Mines and the Mining and Mineral Resources Research Institute at The Pennsylvania State University. The research performed within this particular project is oriented primarily toward standard methods of sampling and characterizing respirable coal mine dust underground so that the chemical, physical, and morphological characteristics are known and can be related to the incidence of coal workers' pneumoconiosis (CWP) in Pennsylvania.The research was initiated by con¬ducting a search of the literature to determine what coal and geologic variables may be related to CWP. The effects of coal rank, free silica content, the mass of respirable dust, and the level of trace elements were the major variables studied. It seems to be evident that the free silica content, the rank of coal, and the mass of respirable dust are the major concerns in defining the causes of CWP. However, based on the literature survey, the authors have concluded that verification of the causes of CWP is a multivariate problem and must be analyzed in an appropriate statistical manner.The results of a multivariate analysis of ten trace elements recorded on Pennsylvania coals are presented. Five of these trace elements were found to be of use in differentiating one coalfield from the others. Of these five elements, chromium and zirconium showed a strong positive correlation with the rank of coal while strontium showed a negative correlation.The design of the field sampling work and its application in future research is the final topic discussed. The sampling plan is oriented toward continuous miner sections with eight-stage impactors as the collection equipment. All of the field work will be conducted in the coal measures of the Allegheny Formation and above with both dust and channel samples being collected in the same mines.Coal workers' pneumoconiosis has been an important topic of concern to miners, mining engineers, and epidemiologists for decades. The general cause of the dis¬ease, the inhalation of coal mine dust, is well known, but the specific coal and geologic variables that affect the incidence and severity of the disease are still subject to debate and study. The primary objective of this study is to identify those variables of Pennsylvania coals that contribute to the CWP problem. To accomplish this task, a field sampling program is to be conducted to relate the characteristics of the coal dust, the coal seam properties, and the geologic variables to the occurrence of CWP.The first year of this study has been involved with both a literature review and experimental work oriented toward identification of causal variables related to CWP. The results of this work are presented here along with plans for implementation of the findings in future research.The previous studies of CWP causal variables have been conducted by scientists, engineers, and medical personnel. Many different types of studies have been performed with emphasis on interpreting the effects of dust mass concentration, mineralogy of the coal, the rank of the coal, and trace element concentrations upon the incidence of CWP in various coalfields. Most of the research has been conducted during the last two decades, with the British Isles, West Germany, and the United States being the primary countries involved.The review of the literature was conducted to determine which variables are likely to warrant further study in Pennsylvania. Previous research studies have related CWP to free silica and other mineral content, the rank of coal, the mass of dust in the working place, and the trace elements in the coal and lung dust. In the following sections, each of these topics will be discussed and analyzed."

Jan 1, 1988

By Paul Biggs

This report presents information on 77 waterflood projects in 31 Montana oilfields. The study shows the locations of the projects, the sources and amounts of injection water, and the results in oil produced. Waterflooding, a secondary recovery technique, began in Montana about 40 years after the initial oil discovery in 1920. Often, the difference between water disposal by injection and pressure maintenance operations is not clear. Water injected at the projects in 1973 was 157.7 million barrels. In 1973, the 31 fields having waterflood projects produced 28.3 million barrels of oil valued at $88.4 million. Both in volume and value, this represents over 80 percent of the State's 1973 oil output. The projects are making possible the recovery of additional oil, thus contributing to the conservation of oil and lessening the impact of the current oil shortage.

Jan 1, 1976

By Victor E. Kral

The Modarelli iron deposit , formerly known as the Requa iron deposit , is 44 miles by road south of Palisade , Nev . , on the Southern Pacific and Western Pacific Railroads . Construction of 10 miles of new road, which is necessary in case the property is exploited , will reduce this distance to about 28 miles . The deposit was discovered in 1905 , and patent was obtained in 1907 . The present owners obtained title to the property in recent years by paying the delinquent taxes . There has been no production . The ore deposit is a replacement of a Tertiary volcanic believed to be a rhyolite . Except for evidence of slight shearing , the deposit has no apparent structure . Hematite is the principal ore mineral ; it is fine-grained and is associated with very fine-grained apatite and unidentified minerals assumed to be alteration products of residual rhyolite minerals .

Feb 1, 1947

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were transmitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

By M. J. Kovalik, D. E. Wolfson, F. Fischler

Plastometric tests were made to determine the maximum thickness of the plastic layer for different U.S. coals . The effect of test variables on the maximum thickness of the plastic layer was studied . The values for the maximum thickness of the plastic layer were found to be related to the Gieseler maximum fluidity , plastic temperature range , free swelling index , and other plastic properties of coals . Only a general relationship was observed between the plastometric parameters obtained in these tests and the coking properties of coal .

Jan 1, 1964

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By A. Sainato, S. J. Kravits, G. L. Finfinger

This report describes a project conducted by the Bureau of Mines in which the accurate directional drilling of a borehole was demonstrated with the objective of intercepting a designated target. The project was conducted at Navajo Dam in northern New Mexico at the request of the Bureau of Reclamation. Borehole survey and drill logs are provided in an appendix. The trajectory of the demonstration borehole was designed to intercept a 5-ft-radius target at the final or "punchout" distance of 885 ft. The elevation of the borehole at this distance was within the target; the borehole punchout coordinates were 8.81 ft southwest of the target. As a result of the demonstrated accuracy, the Bureau of Reclamation has contracted the accurate drilling of boreholes as long as 600 ft from the inside of a short tunnel, to control water seepage in the right abut- ment. This resulted in a substantial cost savings compared to the orig- inal plan of constructing a longer tunnel and drilling 150-ft boreholes.

Jan 1, 1987

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1330, however, was unusually dry and represents what may be termed "extreme low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscohonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.

Jan 1, 1931

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By E. C. Lane

The motor gasoline that is being marketed in the United States this summer is slightly more volatile than that sold a year ago. The increase in volatility is shown by a lowering of the distillation temperatures, ranging from 2°F. at the average initial boiling point to 4°F. at the average end point. During the past nine years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the eighteenth in the series. The cities in which samples were collected have been chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country. Samples were collected in Omaha as well as in the 11 cities where samples were taken last winter. It was believed advisable to include samples from Omaha in order to give a better balance to the survey for the country as a whole.

Jan 1, 1928

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By Franklin D. Slagle

Porosity and bulk-and sand-grain-density values were determined for 2,040 core samples of 30 formations from 47 wells in New York, Ohio, Pennsylvania, and West Virginia, and are compiled for petroleum industry use in well-log evaluation and geologic studies.

Jan 1, 1967

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948