Search Documents

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By Steven K. Ruggieri

This report describes the use of the sprayfan auxiliary ventilation system for methane and dust control on continuous miner sections to potential users. The sprayfan auxiliary ventilation system is a modified water spray system which directs intake air to and across the front of a continuous miner to prevent build up of methane gas and dust concentrations. This user's manual contains practical information concerning sprayfan: a. Description and capabilities b. Design c. Installation d. Operation e. Maintenance. Underground tests, independent laboratory tests, tests by MSHA, and independent installations by coal producers have confirmed the performance of the sprayfan system. There are currently 150 sprayfan systems in operation in underground coal mines.

Jan 1, 1981

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By W. O. Vanderburg

The leasing or tribute system has been an important factor in the development of our metal-mining industry, particularly in the gold and silver mines of the Western States. It has received its widest application in. the early history of many camps and in the last stages of many mines. The system is especially adapted to mining where the ore's occur in narrow veins or are erratically distributed in small bunches or pockets so that selective mining, hand sorting, screening, or hand cobbing is required to produce shipping or milling-grade ore. The leasing system is also applicable to the development of prospects where the owners are unable or unwilling to assume the risks of searching for ore. The virtue of the system lies in the opportunity it affords miners with little capital to get started; at the same time, it rives owners an opportunity to have their property developed at small cost.

Jan 1, 1934

By Craig C. Hustwit

A pilot-scale treatment study was conducted on a copper-zinc bearing metal mine drainage using a pipeline treatment system called the In-Line System (ILS). The objective of this U.S. Bureau of Mines study was to determine whether the ILS could be extended from the treatment of coal mine drainages to the treatment of metal mine drainages. Hydrated lime (Ca(OH)2), quick lime (CaO), and caustic soda (NaOH) were used to neutralize the drainage. A novel reagent slurry of Ca(OH)2 and type C fly ash was also evaluated. Except for Ca(OH)2-fly ash slurry, treatment performance was evaluated for all reagents at pH values of 7,8,9, and 10. The Ca(OH)2-fly ash slurry was evaluated at a pH of 10. All reagents tested neutralized the metal mine drainage and substantially reduced the dissolved metal concentrations. It was concluded that the ILS could be useful in the treatment of metal mine drainages.

Jan 1, 2010

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruction3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1969

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate's dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

By O. H. Metzger

This is one of a series of papers on placer mining in the western United States. The author has endeavored to give a general outline of the available placer deposits in Boise County, Idaho, together with a description of current practices and the recovery costs of the principal producers. The paper is based on a field examination by the author in May and June 1937. Boise County (fig. 1) is in the southwestern part of Idaho. It has a maximum length of 60 miles, a maximum width of 42 miles, and an area of approximately 1,600 square miles.

Jan 1, 1938

By David A. Monaghan

This report describes the results of a 2-year investigation of extensible face ventilation techniques and systems for use at the working face in underground coal mines. The goal was to provide a safe and convenient method of maintaining the extensible system within 10 feet of the face, thereby ensuring good ventilation. A summary of approximately 20 extensible ventilation systems proposed or tried in the past is included for reference, together with a detailed description of the design, construction, and underground testing of a new extensible brattice panel and a new fiberglass duct system. The extensible brattice system utilized a special panel which could be pushed forward as the miner advanced. Brief testing in three mines revealed some conflict with the mining cycle and led to recommendations for two improved designs. The extensible duct system was designed for a Goodman borer and utilized a telescoping tube on the left side of the roof, so that it could be extended without interfering with the miner operator. For mine sections with right-hand return ventilation, a special flat tube section is used to cross over the entry. Underground testing showed substantial improvement in face ventilation without interfering with production.

Jan 1, 1976

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By R. A. Isberg, D. A. Parrish, H. Kramer

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75% coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 3, 1981

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projets programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By P. C. Tully

The vapor pressure-temperature relationships for saturated pure liquid nitrogen are calculated by the Strobridge equation using a digital computer. This information is presented in two tables: first) in pressure increments of 0.1 psi from 1.8 to 492.9 psia) and second) in temperature increments of 0.1° from 63.15° to 126.26° K. These tables should facilitate the calibration of temperature-measuring devices over this temperature range.

Jan 1, 1967

By Steven G. Grannes

This U.S. Bureau of Mines report summarizes Federal mandatory belt conveyor automatic fire suppression system installation requirements and inspection procedures, identifies system failure modes observed during in-mine investigations, and suggests system design and maintenance upgrades which, if implemented, would result in an improvement in overall system reliability. This report is a compilation of recommendations based on discussions with Mine Safety and Health Administration (MSHA) inspectors, review of manufacturer's literature, discussions with mine personnel, and research investigations of automatic fire suppression system performance in the laboratory and in mines. The Code of Federal Regulations (CFR) requirements for installation, inspection, and maintenance of fire suppression systems should be regarded as minimum standards.

Jan 1, 1990

By G. W. Birge

This report describes the carbonizing properties of the principal coal beds of McDowell County, W. Va. Coals from 14 coal beds were selected for study: Upper Cedar Grove, Middle Cedar Grove, Lower Cedar Grove, Eagle, Douglas, Iaeger, Sewell, Welch, Beckley, Fire Creek and Pocahontas Nos. 3, 4, 5, and 9. Selection was based upon estimated minable reserves. McDowell County coals rank either as high-volatile A, medium-volatile, or low-volatile bituminous coal, and this variation in rank is reflected in the wide diversity of the carbonization properties of the coals. All coals tested were either satisfactory as mined or could be upgraded to meet present chemical standards for metallurgical coke; the coals produced strong coke, as determined by ASTM shatter and tumbler tests.

Jan 1, 1958

By S. M. Runke

The pegmatite investigations at the Rapid City, S. Dak., Experiment Station during; the pact 3 years have been primarily a study of recovering beryl from nonlithium-bearing pegmatite rock by continuous-testing methods. Beryl concentrates containing 25 to 88 percent beryl were produced from rock that ranged in beryl content from 0.1 to 2.5 percent. The beryl recovery ranged upward from 70 percent but averaged better than 80 percent. Although promising results have been obtained with flotation methods for upgrading these concentrates to standard specifications, additional work is needed to improve and simplify the procedure. In addition, it was demonstrated that several potentially useful coproducts could also be recovered from pegmatite rock. The principal coproducts were mica, feldspar, and quartz. A heavy-mineral product also was made from pegmatites containing tin, tantalum, and columbium. The recovery if these minerals in products meeting the specifications of the commercial users has been reserved for future study. The investigations also included studies on extraction of beryllium from both high-grade beryl and flotation concentrates of medium beryllium content. The procedure investigated consisted of sintering beryl or beryl flotation concentrates with limestone, acid curing the resulting sinter with sulfuric acid to dissolve the beryllium, and water leaching to extract the beryllium. Over 90 percent of the beryllium was extracted by this procedure. Most of the optimum conditions and quantities of reagents were determined for dissolving the beryllium. As aluminum and iron also were taken into solution by the acid, further research is needed on methods of recovering high-grade beryllium salts from the solutions containing these elements.

Jan 1, 1957

By Corale L. Brierley

Accumulations of microorganisms in the in-situ leaching environment are believed responsible for plugging of the orebody and thus decreasing uranium extraction. To assess the contribution of microbial growth to this problem, packed columns of ore and core specimens were leached in the laboratory. Samples collected at four in-situ uranium mining operations revealed pseudomonads, xanthomonads, Bacillus sp. and Micrococcus sp. in numbers of 105 cfu/ml. These microorganisms, inoculated into simulated leaching conditions, decreased permeability in two uranium ores by one order of magnitude in 20 days. Hydrogen peroxide (0.2 g/l) alleviated microbial plugging in the laboratory. Periodic injection of hydrogen peroxide through the production well into the orebody may reduce microbial plugging problems in the field.

Jan 1, 1982

By S. M. Shelton, A. L. Engel

"This report presents the results of investigations of ore-testing projects assigned to the Ore-Dressing Section, Metallurgical Division, Bureau of Mines, at the Mississippi Valley Experiment Station, Rolla Mo. During the fiscal year ended June 30, 1941.The manner of approving ore-testing projects has been explained in a previous reports. 4/ The testing procedures likewise have been described. 5/The treatment methods described are based upon laboratory experiments with small amounts of sample and naturally are subject to the inherent, normal, limiting conditions of such procedure. It is not intended to describe treatments in detail, but rather to indicate applicable methods. Local operating conditions, when the laboratory results are applied to plant operations, may require further study. Large-scale pilot-plant tests should be made before commercial operations are begun, so that translation from the experimental stage will yield satisfactory results."

Mar 1, 1942