Search Documents

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No. H0155113, "Noise Abatement of Continuous Mining Machines." It reviews, briefly, the aboveground tests performed on a Jeffrey 120M conveyor that were documented in Vol. I of the subject contract; and describes the performance of treatments implemented on underground equipment. The noise level at the operator's position in the aboveground-test facility was reduced from 101.5 to 91 dBA using treatments with satisfactory - aboveground - durability. Extensive underground evaluation has been performed only on the constrained layer damping, which has reduced the conveyor noise by 2 to 6 dBA depending on the operating conditions, and has been shown to be sufficiently durable. Other promising candidates for exploratory evaluation include resilient layers for the top/bottom decks, and smoother discontinuities between adjacent conveyor sections.

Jan 1, 1983

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By Richard L. Rains

The U.S. Bureau of Mines conducted a field study of mines and prospects of the Black Canyon RARE II area (No. 5061), Inyo County, California, from June to October 1981. Geological) geochemical, and geophysical studies were conducted by the U.S. Geological Survey. The Black Canyon RARE II area is east of Owens Valley and 6 mi east of Bishop, California. The principal mineral commodities are gold, silver, lead, zinc, and tungsten. Properties with resources in and adjacent to the area are listed in table 1; the locations are shown on figure 1.

Jan 1, 1983

By R. V. Ramani

This report is volume 3 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Methane Generator subsystem of the Master Design Simulator. This subsystem is used to determine methane emission rates into the mine environment. These flow rates are then used by the simulator in planning primary and secondary ventilation systems, planning a methane drainage system, and analyzing complex ventilation networks. Both steady state and unsteady state gas flows are included, and have been modeled as second order nonlinear partial differential equations. Finite difference equations are used to obtain numerical solutions to the models using a central differencing scheme. An application of the model is presented. The appendices include derivation of the gas flow equations used in the model as well as a users manual for the computer program.

Jan 1, 1974

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB). Shovel/trucks, front-end loaders trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRB truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation), result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985

By Terry J. Close

Between 1986 and 1989, at the request of the U. S. Bureau of Land Management, personnel from the U. S. Bureau of Mines Western Field Operations Center studied the highly-mineralized, 25,335-acre, Crack Canyon Wilderness Study Area (UT-060-028A), to evaluate its identified mineral resources. The 16-mi-long, 2-mi to 4-mi-wide stud/ area is on the southeast side of the San Rafael Swell, about 40 mi southwest of Green River, Emery County, southeast-central Utah. The study area is underlain by Mesozoic sedimentary beds. Uranium, the principle mineral resource, occurs in two formations. The principle uranium deposits are in mudstone, sandstone, and conglomerate lenses in the 22-mi-long outcrop of the Triassic Chinle Formation which parallels and straddles the northwest boundary of the study area, Some small low-grade uranium occurrences and an extensive gypsum deposit are hosted by the Jurassic-age rocks that underlie the southeast part of the study area.

Jan 1, 1989

By A. Gene Collins

Potassium, lithium, strontium, barium, and manganese are present in many oilfield brines, None of them except barium is determined routinely in brine analyses. Therefore, sensitive and accurate flame-spectrophotometric methods were developed. Potassium, lithium, and strontium were determined by a standard-addition technique in ethyl alcohol solutions. Barium and manganese were determined in ethyl alcohol and normal propyl solutions, respectively, after interfering substances were removed.

Jan 1, 1962

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By James E. Bell, Clyde B. White

"INTRODUCTION The Friedensville district was one of the most important zinc-producing areas in the United States from 1859 to 1893. The ore minerals near the surface were principally calamine and smithsonite, but with depth sphalerite was found in increasing proportions. The ore bodies of the district are reported to have been in chimneys, occurring in folded and faulted beds of Beekmantown limestone of Ordovician age.The Correll was one of five mines near Friedensyille that were exten¬sively exploited. The high-grade ore shoots were mined to a depth of several hundred feet, but it is believed that inability to compete with lower-cost production elsewhere, rather than exhaustion of the ore bodies, compelled the mines to close.There is no record to indicate that any attempt was made during the period of operation to explore for additional ore in the limestone beds down the dip below the mine workings. The possibility that exploration might reveal additional ore in the limestone beds below the known ore shoots led the Bureau of Mines to diamond-drill the Correll property between September 1943 and January 1944."

Jan 1, 1948

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976

By William G. Pariseau

A brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis is presented that includes detailed instruction for input data preparation and how to obtain output.

Jan 1, 1978

By Lloyd Williams

1. This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By W. Dan Walker

In recent years the Federal Bureau of Mines tested and approved four new types of self-contained breathing apparatus and a facepiece designed for use with the McCaa 2-hour self-contained oxygen breathing apparatus. The Bureau also developed and perfected a battery-powered lifeline telephone for use in mine rescue and recovery operations. Some of this equipment is described in Bureau of Mines Information Circular 7413.4/ This publication is a revision of information Circular 7413 and presents pertinent information on more recently developed mine rescue equipment. The breathing apparatus described herein are 1/2- and 3/4-hour sell-contained types of much simpler design than the conventional 2-hour self-contained oxygen breathing apparatus ordinarily used by mine rescue crews; however, it is just as important to select rescue crews carefully and to train them properly in the use, care, and limitations of the newer types of apparatus as well as the older, established types, if the newer types are to be used safely. The Bureau of Mines recommends that 1/2- and 3/4-hour self-contained breathing apparatus be used only as auxiliary equipment in mine rescue and recovery work and that the capabilities and limitations of the apparatus should be well understood by those who wear the equipment.

Jan 1, 1957

This report describes the work performed by Mine Research Company in developing a prototype mobile roof shield during 1971-1972 for the U. S. Bureau of Mines, along with background information leading to the design decisions adopted for the project. In addition, the report evaluates the choice of design and analysis and the results of the project in terms of future possibilities of mobile roof support systems. The report begins with the discussion of the problems of designing, building, and using mechanical and hydraulic roof support in coal mines. It then gives a historical summary of past work with discussions of the design choices made for previous roof support systems.

Jan 1, 1973

By Mark Sanders

This report compares a proposed 10/60 "piggyback" 02 generating self-rescue unit to the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and subjects performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 or self-rescuer attached to their belts. Task completion time was longer on all tasks when wearing the 10/60 unit, although only locomotion was statistically significant. The 10/60 unit was bumped over 100% more often than the standard self-rescuer. Implications for design of the proposed 10/60 container are: 1) unit?s container must be extra durable to withstand the added abuse it is likely to receive by low coal miners; and 2) extra consideration must be given to preventing the device from slipping on the belt while working, especially in low coal.

Jan 1, 1980

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By Mark P. Meyer

A mineral investigation of the Chugach National Forest, Alaska was conducted jointly by the U.S. Geological Survey and the U.S. Bureau of Mines from 1979 to 1983 as part of the RARE II program. The U. S. Geological Survey remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. Previously unreported mineralization in three areas, Long Bay, Wells Bay, and Miners River were discovered in the western portion of the SOUND study area. Copper, lead, zinc, gold, silver, nickel, cobalt, fluorite, and arsenic were found in north-northeast to north-northwest trending shear zones, veins, felsic dikes, and granitic intrusives in Tertiary Orca Group metasedimentary rocks.

Jan 1, 2011

By William M. Schafer

Forage plots were established on agricultural lands contaminated by acid mining waste. The acid produced through oxidation of pyrite and other sulfides caused elevated solubility and plant availability of copper, zinc, and arsenic which killed vegetation and polluted surface and groundwater. Soil amendments including agricultural lime (CaCO3), hydrated lime (Ca(OH)2), phosphorus, and organic matter were used to reduce the toxicity of metals. Several acid-tolerant grasses were used to vegetate the amended soils. Various soil extraction techniques were used to see which best correlated with vegetation performance. The extractions corresponded to three "forms" of metals in soil including soluble (water-saturation extract); plant-available/weakly adsorbed (DTPA extract); and total (HNO3/H202 extract). Of the extractants tested the DTPA levels appeared to correlate best with metal levels in plant tissue. The DTPA soil extractant serves as a useful tool in predicting potential phytotoxicity of mine waste materials.

Jan 1, 1989