Search Documents

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By M. E. Poad, M. M. McDonald, J. C. Johnson, W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-element method for evaluating shaft pillar mining plans and shaft stability. This report focuses on mine measurements and calibration of the two-dimensional computer model and is the second in a series of three Reports of Investigations describing the Ross shaft study. In this study, borehole extensometers and other instruments were installed to provide data for model verification and to monitor the shaft. Results of the recalibrated two-dimensional model (UTAH2) confirmed the premining stability evaluation. However, after mining began, concern was expressed because cracks and other signs of ground motion appeared at considerable distances from the area of active pillar mining. In part 3 of the study, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the observed effects were within expectations and that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 1995

By D. Harrington

The mining industry of the United States has for many years possessed the dubious aistinction of having the poorest accident rate of all of the major lines of industrial endeavor in this country, and until recently there ras little or nothing to show that any material improvement might be expected. However, there are now numerous trends indicating that the corner has ceen turned at last, and it is strongly hoped that the mining industry is likely to follow the railroads, the cement and other industries in operating with occurrence of only a reasonable amount of loss of life and limb through accidents. The complete accident figures for metal and nonmetallic mineral mining for 1931 are not yet available, but fragmentary data shor that 1831 vill un- questionably have very low accident rates, probably the lowest in the history of our metal mines. One underground metal mine has produced over 14,000,000 tons of copper ore rithout a fatality; another metal mining company with an electric slovel operation has handled upwards of 75,000,000 tons of material, copper ore and waste, without the occurrence of a fatality; an iron-ore compan, which orns six mines (three underground, three open pit), has operated every one for a year or more without a lost-time accident with a con- siderable number of employees and a large production; and alot.er iron-ore producer with 30 mines and about 3,000 employees as an average of nearly 10 months of operation in 1931 without a lost-time accident. umerous other wonderful safety records of metal mines in 1931 indicate unmistaimbly tat the record of the noncoal mining industry of the United States as a role in 1931 will undoubtedly be found to be excellent. According to the latest relatively complete figures (those of 1930) available for the coal industry, fewer than 650,000 persons are employed in and around the coal mines of the United States, the figures indicating at a little over 493,000 people are engaged in bituminous mining and a little under 151,CCO in anthracite mining. Bureau of Mines complete figures suc that 2,053 persons were killed and 103,821 non-fatally injured in our coal

Dec 1, 1932

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980

By C. F. McCarroll

The effectiveness of an industry?s safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and ?service" contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

By George J. Conroy

This Bureau of Mines report summarizes the results of a study of mine inspection records covering 2,200 mining installations over a 3-year period ending December 1974. Tables show the relative frequency of violations of certain provisions of the Coal Mine Health and Safety Act of 1969 in particular areas of concern, such as circuit breakers, grounding, and permissibility. Examples of past use of the data and analyses are presented.

Jan 1, 1976

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By Mark S. Sanders

This report presents a summary of the work reported by Sanders and Kelley (1981). A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were indentified. The visual attention locations are contained in this report. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars & scoops were used to test the procedure. Illustrative results are presented in the report.

Jan 1, 1981

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961