Search Documents

Poor floatability of fine particles is known to be the main cause of the low recovery of ilmenite in Panzhihua, which is the largest titanium mine of China. To get an optimum ilmenite recovery, selective flocculation, and flotation of fine ilmenite was investigated through flotation tests, particle size analysis, zeta potential tests and scanning electron microscopy. The results indicate that carboxymethyl cellulose (CMC) shows flocculation effect for both ilmenite and titanaugite without selectivity, while selective flocculation could be realized by the combination of water glass and CMC. It is because that competitive adsorption would take place on these two kinds of mineral when water glass and CMC are used together. On the surface of ilmenite, the adsorption ability of CMC is stronger than that of water glass, so that CMC can absorb to the same extent irrespective of the presence of a pre-adsorbed layer of water glass and ilmenite particles is flocculated by CMC. The same cannot be said of the titanaugite phase as water glass strongly adsorbs onto the titanaugite, and the adsorption of CMC is hindered. Therefore, the titanaugite particles keep dispersion. Furthermore, the flotation of fine ilmenite particles is feasible as the ilmenite floccules could react with sodium oleate. In the flotation separation of Panzhihua ilmenite ore, the recovery of TiO2 increased from 52.63% to 68.28% by selective flotation. Keywords: ilmenite, flotation, selective flocculation, adsorption

Sep 1, 2012

By Q. Zhang

Phosphate tailings through Flotation contains large amount of dolomite which is difficult to be separated from apatite. In this present research, phosphate tailings is recycled by Flotation i.e. re-processing. High-purity dolomite with purity as high as 91.17% is seperated, which contains 19.82% of MgO. The results of orthogonal test show that the effect of various levels of different factors on the high-purity dolomite floatated. Future utilization of purified dolomite is also discussed: magnesium fertiliser especially magnesium phosphate is expected to be an ideal product from high-purity dolomite.

Jan 1, 2014

By V. A. Chanturiya

The results study the minerals oxidation were obtained by us during the methods of microscopic, FT-IR spectroscopic, XRD and chemical analyses of sulphides in tailings of copper-nickel wastes in Kola peninsula. Sulphide minerals begin to oxidize already at the stage of stockpiling and initial stages of storing. The proportion of non-ferrous metals and magnesium oxide increases with time, calcium partially precipitating in the form of gypsum. Comparison of heavy metal contents in pore solutions in cur-rent and stale copper-nickel ore concentration tailings has revealed a significant difference in practically all the parameters. The lower metal contents in current tailing pore solutions (by 5~30 times) are probably due to the presence of float reagent residues blocking oxidation. Much lower concentrations of magnesium and calcium can be accounted for by the difference in kinetics: the rate of sulphide oxidation at this stage is much higher than that of solution interaction with non-metallic minerals as the result of which the solid phase ? solution equilibrium is not achieved. It is generally believed worldwide that it the mining wastes with acidic pore solutions that pose the greatest hazard for the environment. Our findings suggest that although the solution pH in all the samples is higher than 7.8, the contain heavy metal concentrations by far exceeding permissible values. The direct determination of the total and silicate Ni contents in the tailings from current production and in storage tailings has shown that both sulphide and silicate Ni forms occur in tailings. However, the role of silicate Ni is much larger in the storage tailings. The average silicate Ni content accounts for 10% of the bulk Ni content in the current tailings and it increases to 40% in the storage tailings. Thus, the storage tailings are marked not only by sulphide oxidation and the removal of water-soluble sulfates, but also by the interaction of sulfates with the silicate matrix. Although complete equilibrium is not achieved even within 30 yr under polar-region conditions, the major part of the Ni in fine-grained fractions passes into silicate form. The probability of Ni transition to the silicate form directly correlates with the dispersion of the material and the amount of chemically reactive serpentine and hydrochlorite. The migration of Ni as sulfates and its precipitation by chemically active silicates distorts the distribution of this component in the coarse- and fine-grained fractions that are typical of tailings from the current production of copper-nickel ores. On the one hand, the variation of the mode of Ni occurrence in storage tailings lowers the value of technogenic raw materials as a source of this metal.

Jan 1, 2014

By Chandra Sekhar Gahan

The present study aimed to investigate the depyritization of coal using iron oxidizing and sulphur oxidizing acidophilic chemolithotrophic microorganisms in an iron free 9K growth medium at varying pulp densities. Three different coal samples used in the shake flask study from three different countries such as domestic anthracite (Korean), Indonesian and Chinese lignite. Experiments were carried out in batch at a controlled temperature of 35 °C and varied pulp densities of 8%, 10% and 12% (w/v) with a working volume of 100 ml containing 10 ml of microbial inoculum and 90 ml of the iron free 9K growth medium. Coal samples were crushed and ground to fine size fractions <100 microns by attrition mill wet grinding. The progress in the experiments were followed by the regular measurements of pH, redox potential, viable planktonic cell count, residual Fe2+ ion concentration, amount of acid addition and amount of slaked lime addition. The pyritic sulfur removal percentage varied between 90-95% with highest sulfur removal with China coal (95%) followed by Korean Coal (93-94%) and slightly lower level for Indonesia coal (90%). However the pyrite oxidation was highest for Korean coal ranging between 78-80% followed by a similar level of pyrite oxidation of 50-61% for the Chinese and Indonesian coal. It was found that 10-12% pulp density would be fairly feasible for all the different coals tested leading to an economical process. Another benefit from this study is the iron free 9K growth medium, which will reduce the operation cost and overall it?s an environment friendly process.

Sep 1, 2012

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By Xiaolu Ye

"Comprehensive utilization of Bi and Sn from the tin-associated polymetallic tailings by “gravity separation – flotation combination process” has been studied, which was verified that the novel process is an effective method to deal with the high content pyrrhotite tin-associated polymetallic tailings. In this investigation, ore property analysis and magnetism analysis of pyrrhotite were conducted to research and develop reasonable beneficiation flowsheet. The results of ore property analysis present that pyrrhotite was not closely related to bismuth and tin minerals. Particle size analysis results indicated that pyrrhotite was mainly in the form of fine particles. The magnetic analysis results show that pyrrhotite was distribution in all the three types of pyrrhotite in a single mining area, which indicated that variable magnetism of with different crystal structure pyrrhotite. The process of “low intensity magnetic separation - high intensity magnetic separation” shown an excellent adaption for the high content pyrrhotite tin-associated polymetallic ore compared with the single flotation process based on the magnetism variable of pyrrhotite. The results of whole process test indicated that a bismuth coarse concentrate assaying 5.63% of Bi at 81.77% recovery was obtained, which treat the conditions for the Bi-S separation flotation. In addition, the content of sulfur in the tin concentrate decreased from 2.5% to 1.5%, which provided a new reference for other tin-associated polymetallic tailings. INTRODUCTION Tin has been applied extensively in catalytic chemistry, gas sensors, tin plating, and plumbing. Tin-bearing polymetallic ores have been the important deposit types to recycle tin with the rapid depletion of mineral resources. The comprehensive utilization of the associated elements has been a preoccupation for the mineral processing researchers."

Jan 1, 2018

By F. Bello, J. Engels

"During 2012 and 2013, Minera Esperanza conducted a series of thickening and deposition trials to identify design and operational parameters associated with increased thickening of its tailings. These trials focused on benchmarking the current solids concentration of tailings (62 - 64%) in anticipation of an increase to 67% solids once two new 45 m diameter deep-cone paste thickeners are commissioned in 2014. These trials studied the sedimentation and rheological characteristics of the existing tailings and performed deposition modelling to assist with developing short- and long-term designs for the tailings storage facility. To verify and optimise these models, Minera Esperanza considered a series of laboratory, pilot, and industrial-scale deposition trials. This paper provides a review of the trials conducted in the laboratory and at industrial-scale and considers the results and optimisations for the short- and long-term design of Minera Esperanza’s tailings storage facility."

Jan 1, 2014

By M. Barsky, E. Barsky

It is generally accepted that the optimal flow velocity for gravity classification is the final particle settling velocity or, which is the same, the particle spin velocity. However, we have found differences between the settling velocities and the spin velocities of the very same particles. Here we present the results of experiments in a cascading gravitational classifier comprising eleven stages. The feed material was introduced at each stage successively, from the first to the eleventh. The optimal flow velocity was determined for each case. From these experiments it follows that the value of the optimal flow velocity depends to a greater extent on the point of introduction of the feed (i.e., on the design of the device) than it does on the interaction between the solid phase and the flow.

Jan 1, 2003

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

By J. Y. ` Xie

The paper introduced bio-oxidation plants of refractory gold concentrate in China and CCGRI cultures. CCGRI cultures are composed of bacteria and archaea. Archaea Ferroplasma acidiphilum is very thick and fills whole mineral surface. It plays a more dominant role in CCGRI process. Several years of practice has proved that the operating temperature in bioreactors between 38~52?,gold recovery is almost same. Pulp concentration has been increased each year and reached to 25%.

Jan 1, 2014

By Ashok Kumar, Subhadra Sen Dr. Rashmi Kumari, D. P. Chakraborty, Ajay kumar Gupta

The blast furnace coke quality depends on the characteristics of coal blend, pre-carbonization techniques adopted such as stamping, vibro-compaction etc., and coking conditions. Of the above, coal blend plays a significant role in the production of quality coke. Furthermore, the quality of the blend depends on the quality of individual coals and their interaction making up the blend. During transportation and stockpiling, coal is in contact with air for periods of time that sometimes may exceed several months. During this time, reaction with oxygen in the presence of water, sunlight and possibly elevated temperatures may take place. The resulting weathered coal suffers some alteration in its technological properties, which in turn affects coke quality for Blast Furnace operation adversely. In this work, two coals belong two prime hard coking and hard coking categories, namely Illawarra & Tahmoor, were selected and kept in a separate stock pile for a period of 120 days. These coals were characterized in terms of proximate, rheological & petrography properties at a regular frequency. This report summarizes the impact of weathering on the coking behaviour of these two coals in terms of properties as mentioned above. However, the rate of loss depends on coal rank and storage conditions. This has been seen through this study that the loss depends on coal rank and storage conditions. Deterioration of rheological and petrographic properties were seen higher for low-rank coals, like in this study Tahmoor, which is a low rank coal, compared to Illawarra showed higher degree of coking property degradation within the same time period under identical environmental conditions. Low-rank coal deteriorates at a faster rate because low-rank coal is dominated by free radicals that easily react with oxygen, resulting in the creation of various carbonyl groups and weathered vitrinite. Based on the results obtained in this study, size of stock piles for different qualities of coals to be maintained, at a specific time, can be determined and recommended, so that target coke quality is always achieved.

Jan 1, 2018

By S. Castro, L. Uribe

Seawater can be considered as a particular process water with a high concentration of NaCl (about 0.5- 0.6 mole/L) and high concentration of hydrolyzing metal cations (mainly, Mg2+ and Ca2+ ions). Micro-flotation tests, induction time measurements, and zeta potential measurements have been used to investigate the effect of these ions on the natural floatability of molybdenite. The results demonstrate that molybdenite is strongly depressed in the alkaline pH range over which hydrolysis products of Mg2+ and Ca2+ ions are formed. At pH 10, colloidal magnesium hydroxide seems to be responsible for molybdenite depression in seawater and in Mg2+ solutions. This is also supported by the measurements of the effect of Mg2+ ions on the zeta potential of molybdenite. The mechanism of depression of molybdenite with Ca2+ ions is different, and depression takes place in the pH range were Ca(OH)+ complexes are formed, below the pH of precipitation of calcium hydroxide. Adsorption of the cationic hydroxy species and/or hetero-coagulation of the positive charged colloidal hydroxide on the negative charged molybdenite particles seem to be the main mechanisms involved.

Jan 1, 2014

By H. J. Liang

In this study, zeta potential and contact angle measurements of pyrite before and after interacting with Thiobacillus ferrooxidans are carried out to investigate the changes in its surface properties. The results show that, after pyrite interacting with Thiobacillus ferrooxidans and its metabolite, the surface electricity of pyrite changes obviously, resulting in a notable shifting of isoelectric point to lower pH value, but the contact angle varies little. Bacterial protein plays the most important role in the interaction. This work is helpful to disclose the mechanisms of Thiobacillus ferrooxidans de-pressing pyrite flotability.

Jan 1, 2014

By T. J. Chen

Stone coal containing vanadium is an important vanadium resource in China. Roasting and oxidation of vanadium is the foundation for extracting vanadium from stone coal. This article takes stone coal vanadium ore in Tongshan of Hubei Province as research target to conduct oxidation roasting test on it by using a self-developed low-sodium compound additive and a new optimized technology. Firstly, use potentiometric titration, X diffraction, energy spectrum and electron probe to study valence change, occurrence and phase transition of vanadium during oxidation roasting process. On this basis, primary work is done on oxidation kinetics of vanadium by exploring the steps that control reaction rate during vanadium oxidation process and determining the related dynamic parameter ? apparent activation energy. The study shows that occurrence of vanadium in stone coal of Tongshan is mainly in illite, and that the result of phase transition in roasting process is disappearance of illite containing vanadium, formation of soluble vanadate and potassium feldspar, albite. It further demonstrates that oxidation process of vanadium is step by step (V(?)? V(?)? V(?)), and its oxidation reaction is controlled by diffusion kinetics whose dynamic apparent activation energy is E1=81.19kJ.mol-1.

Jan 1, 2014

By John Ralston

"Interfacial chemistry plays a pivotal role in bubble-particle capture, for it controls whether or not attachment occurs. Surface heterogeneity, degree of surface hydrophobicity, bubble nucleation and related phenomena influence the stability of the aqueous wetting film between a particle and an approaching bubble. The latter must be unstable if capture is to occur. Various techniques that may be used to quantify this interfacial, chemistry-dominated behaviour, are described.The efficient capture of specific particles by rising bubbles and the delicate control of interfacial chemistry that leads to selective capture are central issues in froth flotation. For efficient capture to occur between a particle and a bubble, they must undergo a close encounter, a collision process dominated by hydrodynamics. Should this encounter bring the particle and bubble within the range of attractive forces, the intervening liquid film between the bubble and the particle will drain, leading to a critical thickness at which rupture occurs. The liquid-vapour interface then retreats over the solid particle surface until a stable wetting perimeter is established. The particle and bubble are then joined after this attachment process. The particle may only be dislodged from this state if it is supplied with sufficient kinetic energy to exceed the detachment energy in this detachment process. These various events are now well documented and may be followed using high-speed videomicroscopy (Schulze, 1984; Nguyen et al., 2001).The process of collision can now be described quantitatively for single bubbles colliding with bubbles under various flow regimes (Dai et al., 1998) and appropriate scale up is possible for multiple bubble particle collisions occurring under turbulent conditions (Pyke et al., 2002). In this paper we will be concerned with the role of interfacial chemistry and how this influences the attachment process."

Jan 1, 2003

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014

By A. V. Zimin

It is a well-known fact that usage of reverse cationic flotation in magnetite ores processing enables to improve the quality of magnetite concentrates. We designed an iron ore concentrate technology (with 70 -71 % of iron) including reverse cationic flotation in pneumo-mechanical flotators RIF (developed by RIVS Corporation, Russia) with good biodegradable etheramines as collectors for flotation of quartz. Practical application of high biodegradable flotation reagents decreases environmental impact risk of objects and enterprises of mining industrial complex. This work presents results of development of flotation technology for production of high quality ferruginous concentrates from magnetite ores of Russia and Ukraine deposits. Keywords: magnetite ores, reverse cationic flotation, ferruginous concentrates, pneumatic-mechanical flotation machines, environmental impact

Sep 1, 2012

By N. Gurulaxmi Srikakulapu

The demand for high-grade iron ore has increased the importance of beneficiation of low-grade iron ores. The captive mines of Tata Steel Limited, India has reserves of Banded Haematite Jasper (BHJ) ore assayed 40% Fe, 40% SiO2 and <1% Al2O3. QEMSCAN study has revealed haematite and quartz as a major iron bearing and gangue mineral phases respectively. Liberation characteristics have showed 80% liberation can be obtained at particle size below 10µm. In the present study, reverse cationic froth flotation of BHJ using ether diamines is explored in Denver-D12 flotation cell. Polynomial response surface regression equation coupled with six-factor Box-Behnken design of experiments is used to generate the correlation between process separation efficiency and flotation parameters. Flotation studies of BHJ indicated that concentrate of 62% Fe can be achieved with 62% Fe recovery from Jig concentrate at optimum conditions. The obtained product can blend with pellet fines to feed in blast furnace. Keywords: banded haematite jasper, flotation, box-behnken design, response surface methodology

Sep 1, 2012