Search Documents

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By S. J. Dai

The cadmium and cyanide are main poisonous components in cyanide electroplating cadmium waste water of an electroplating plant in Shenyang. The content of cadmium is about 26 mg/L and the content of cyanide is about 11.782 mg/L in this waste water. The main form of cadmium and cyanide are ions which are Cd2+and CN?. Because the cadmium and cyanide exceeded the standard seriously, the waste water must be disposed before it discharges. The microbiological method of treating heavy metals in wastewater has many advantages. For example, it has a fast adsorption velocity, high processing efficiency, wide range of pH and temperature, few invest, low running cost, no the second pollution and so on. At the same time, the CN? could be degradated by some microbiology. The physical nature, the chemical nature of Bacillus mucilaginosus, the adsorbing condition and adsorbing regular of Bacillus mucilaginosus to cadmium in the wastewater are studied by using Bacillus mucilaginosus as adsorbent removing cadmium from electroplating wastewater. The experimental results show that the adsorbing rate of cadmium is over 92%, under the room temperature(about 25?), stiring revolution in adsorption being 800 r/min for 30 min, pH being 5 , the bacteria being cultured after 5d with the biomass of Bacillus mucilaginosus 40g/L (wet weight). The mechanism in biosorption process of Bacillus mucilaginosus to cadmium is analyzed and discussed by TEM , Zeta potential,and infrared spectroscopy analysis. The results showed, the chemical involving is main adsorbing form, while electrostatic attraction, ions exchange, hydrogen bonding and Van Der Waals force are concerned cooperatively. ?NH2 ?, ?C=O?, ?C=O?NH?CH2, ?CH3, ?OH are main adsorbing groups. At the same time, the floatablity of removing cyanide by Bacillus mucilaginosus is explored.

Jan 1, 2014

By H. H. Li

Reverse flotation is usually used for hematite/silica or bauxite/clay flotation separation in which the silica or clay is floated and rejected. Some properties of these silicate minerals such as particle size and surface characteristics have significant effect on their flotation behaviours. Firstly, the silicate mineral particles (especially clay minerals) generally have fine particle size (< 5 microns) in their natural states or due to overgrinding and they display poor flotation kinetics, consequently having low flotation recovery. Secondly, the wettability difference on different particle basal planes influences the affinity for adsorptions of different types of chemicals such as collectors or macro-molecule. Common polyacrylamide (PAM) flocculants can be used to minimize the exposure of the most hydrophilic planes of clay particles via hydrogen bonding but they can not efficiently enhance the overall particle surface floatability due to the hydrophilic properties of this type of macromolecules. A novel method to improve both flotation kinetics and surface wettability of silicate minerals has been developed and studied. That is to use a temperature-sensitive polymer, poly (N-isopropyl acrylamide) (PNIPAM), as a process aid in the flotation of silicate minerals. Unlike PAM polymers, PNIPAM can induce a hydrophilic/hydrophobic transition on the particle surface when the temperature is changed to be lower or higher than its critical solution temperature (CST). At a lower temperature, the PNIPAM adsorbs on the particle surface via hydrogen bond similar to PAM. It induces strong hydrophobic aggregation when the temperature is increased above the CST. Thus, both floc size and mineral floatability are greatly increased. The flotation results show very good flotation performance and the addition of conventional flotation collector was no more required because the increased particle surface hydrophobicity induced by PNIPAM. Contact angle measurements explained the role of PNIPAM in manipulating particle surface hydrophilic/hydrophobic transition.

Jan 1, 2014

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational health and safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards."

Jan 1, 2003

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By K. Kiangi

On installing the Metso Superior MK 54x75? primary gyratory crusher in Nkomati mine the crusher experienced severe power spikes greater than 1000kW which subsequently led to the crusher tripping under load while processing some of Nkomati?s MMZ ores. Likewise significant losses in throughput were also experienced while processing some of Nkomati?s MMZ ore types. Interestingly the crusher was capable of processing the PCMZ ores without experiencing any power spikes or losses in throughput. Investigations into the challenges faced by the crusher while processing Nkomati?s MMZ ores were conducted using the DEM model in conjunction with the fast breakage model present in Metso?s High Fidelity Simulator. The intentions of the study were to establish the most suitable operating conditions or cavity design that would potentially enhance the performance of the crusher. Likewise an understanding of the effects the feed conditions (size distribution and hardness) had on the crusher?s performance was established. Ore characterization tests were conducted on Nkomati?sPyroxenite, Diabase, Calc silicate and quartzite ores which were from Nkomati?s MMZ ore body. The ore characterization tests conducted were drop weight tests, slow compression tests and elastic modulus tests. Four simulations were conducted used the existing cavity design with various open side settings (OSS) and throws. This established the effects of changing the crusher?s operating conditions on its performance. Four additional simulations were conducted on two cavity designs with reduced volumes. This established the effects of changing the crusher?s cavity design on the crusher?s performance. Thus through the simulations a better understandings of the impact of the crusher design, operating conditions and feed conditions on the crushers performance. Furthermore an analysis of the crusher?s performance was made which was used as a basis for comparisons with the base case simulation. Keywords: crusher, discrete element method, simulation, ore characterization

Sep 1, 2012

By Leming Ou, Longsheng Yi, Qiming Feng, Yiping Lu, Qing Shi, Kun Liu, Guofan Zhang, Yanfei Chen

"Three important components of stirred tanks involved in energy consumption, the impellers and baffles, were investigated to intensify the agitation pretreatment on the flotation of nickel ores. Flotation tests revealed that the stirred tanks with two impellers had an advantage over those with one impeller in intensifying agitation pretreatment, and the higher agitation speed led to better flotation performance of nickel ores. Installation and removal of baffles were also employed in the stirred tanks, and flotation tests demonstrated that with baffles, the flotation grade increased significantly. These agitator design improvements were used to demonstrate that the energy supplied to the system significantly influences the flotation recovery and that if the energy consumption of the agitation pretreatment is ideal, flotation efficiency can be improved. Data from full-scale operations backed up these results.INTRODUCTIONThe flotation recovery of nickel-copper sulphide ore at the Western China nickel mine has historically been difficult due to the presence of large amounts of serpentine minerals (Feng, et al., 2012). Many studies reported that serpentine minerals tend to have a positive potential at pH values up to 9.5, while sulphides (such as pentlandite and chalcopyrite) have a low isoelectric point(Feng, et al., 2012). Serpentine minerals can form surface coatings on negatively charged sulphides surface due to electrostatic attraction when they interact with each other, which may also reduce collector adsorption and increase the hydrophilicity of the sulphide particles. In order to improve the flotation of nickel sulphides, sodium hexametaphosphate, sodium silicate, carboxymethyl cellulose (CMC), and other agents are used to disperse serpentine coating from sulphide surfaces in the flotation of the Jinchuan deposit and other nickel ores in China ( Kirjavainen and Heiskanen, 2007; Lu, et al., 2011). However, it is difficult to improve of the sulphide flotation due to the high dosage and the lack of selectivity."

Jan 1, 2018

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By Mahdi Shevrini, Hamed Haghi

"In this research, the operation of screen classifying in silica processing circuits was investigated and modified by replacement of available trommel screens with teetered bed separator (TBS). In addition the effect of the mentioned replacement and addition of attrition scrubber on quality of final product, impurities removal, recovery and production rate were inspected. Considering screen efficiency problems to achieve certain particle size distribution, hydraulic classifying system was selected instead of trommel screens. Application of suggested plan improved quality and particle size distribution of produced silica significantly. Optimization of size classification in process circuit resulted in increase in production rate up to 21% (from 67% to 81%), silica recovery (from 68.35% up to 83.11%) and relative enhancement in removal of impurities such as Fe2O3 and TiO2. After optimization and stabilization of grinding and size classification section, industrial attrition scrubbing tests were carried out and the best solid percent and retention time were determined i.e. 70% and 6 minutes, respectively. Using sodium carbonate during attrition scrubbing, has major effect on removal of surface coating and staining especially sharp increase in clay removal; therefore 2 kg/t of sodium carbonate can be optimistic point of industrial procedure for this silica processing plant. It should be mentioned that application of attrition scrubbing which is followed by screw classifier for de-sliming were useful for better cumulating of particles in the range of appropriate liberation degree (+106-300µm) and efficient removal of metallic (iron and titanium oxides) and non-metallic (clays and feldspars) impurities."

Jan 1, 2014

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By S. Cagirici, Z. Öztürk, A. Hassanzadeh

Many flotation kinetics models have been studied in the literature. Their applicability was extensively investigated and argued in detail. However, model selection criteria were not adequately discussed from the statistical points of view. In this investigation, the kinetic behavior of a complex copper sulfide ore was studied in a mechanical Denver flotation cell focusing on flotation kinetics of chalcopyrite, pyrite and molybdenite. Different flotation kinetics models including nine common empirical models and four mathematical models namely Hill, Chapman (Sigmodial function), single rectangular (Hyperbola equation) and exponential were applied to the experimental data. In addition to assessment of the goodness of fit criterion for each model, a factor of model complexity was considered using information criteria (IC) (i.e. Bayesian information (BIC), low of iterated logarithm (LILC) and Akaike information (AIC) indices). The obtained results showed that the IC indices could simply manifest the best-fitted model to the experimental data. Whereas, the coefficient of determination values (R2) were relatively same for all models. By taking the R2 and model complexity criteria into account, the exponential model was chosen as the best representative mathematical model to demonstrate chalcopyrite kinetic behavior. However, Chapman model was selected as the best one for the flotation of pyrite and molybdenite. In case of the common first-order flotation kinetics models, fast and slow flotation kinetic model (Kelsall) was reasonably fitted the best to the given data of chalcopyrite. However, the gas/solid kinetics adsorption model was chosen as the best-fitted one for pyrite and molybdenite. Furthermore, it was found that mathematical models represent better results in association with flotation kinetic behavior of chalcopyrite, pyrite and molybdenite due to the consideration of more parameters in modeling. Finally, it was concluded that the IC indices must be applied to the process of model selection due to consideration of goodness of fit, complexity of a model and model consistency.

Jan 1, 2018

By G. C. Li

Gold extraction using iodide leaching from refractory carbonaceous gold ores was studied. Thermodynamic analysis of iodide leaching chemistry had been carried out. Eh-pH diagram of Au-I2-I--H2O leaching system showed that the coordinating active forms from iodides were I3- and I-, while the major coordinate compound formed during iodide leaching was AuI-. For leaching parameters optimization, technological parameters such as I2 concentration, I2 :I- ratio, oxidation assisting agents, liquid/solid ratio, and leaching duration were studied. The leaching results showed that the average Au leaching rate reached 91% and 92% for oxidized ore and roasted primary ore respectively. Leaching process proceeded in weekly acidic or neutral slurry at ambient temperature; the leaching duration was 4 hours. After that gold was extracted from the pregnant liquor by activated carbon adsorption ? desorption ? electrowinning process. Gold recovery was over 93% in the adsorption process, while the gold recovery in electrowinning process was about 95%, provided that the initial gold concentration is 40mg/L or larger. For iodine regeneration it is enough to add hydrogen peroxide in excess into the filtrate after gold electrowinning, all the iodides existing in the solution in any forms would be precipitated in the form of elemental iodine.

Jan 1, 2014

By Katja Ohenoja

Polymer dispersants, also known as grinding aids, are widely used to reduce the viscosity of mineral particle suspensions and to improve energy efficiency during fine grinding. In this study, the effect of polymer dispersant with different molecular structure on the suspension properties in the wet stirred media milling of limestone was studied. The stability of suspension was studied by combining rheological and zeta potential measurements. The PDI value of polymers corresponds to the width of the molecular weight distribution so that low PDI corresponds to narrow MW distribution and high PDI to the wide one. In this study, two traditionally fractionated polymer dispersants with high PDI (over 2) and one novel polymer dispersant with low PDI (1.2) has been tested. It was noticed that dispersants worked as electrosteric stabilizators and prevented the agglomeration of ground limestone particles. The uses of dispersants could increase solids concentration used in the grinding experiments and at the same time lower the particle size and specific energy consumption. The obtained particle sizes were about 1 µm regardless of which dispersant was used or the amount of it. The novel dispersant with low PDI reduced viscosity most when compared with the traditionally fractionated polymer dispersants. Results indicated that even higher solids concentrations can be used at the same amount of dispersant when the novel low PDI polymer dispersant is used. Alternatively, lower dosage of novel low PDI dispersant can be used compared to traditionally fractionated dispersants.

Sep 1, 2012

By R. M. Zhao

The process conditions and mineral characters of cleaning separation stage in magnetite concentration plant are studied in the paper, and the affecting factors and the methods to increase the concentrate grade are analysed and given. The BKJ cleaning special drum magnetic separator is developed specially for the cleaning stage according to process conditions and mineral character. The separation mechanism, structure characters, separation process and excellent adaptability of BKJ special magnetic separator are described. The results in Zhangjiawa Concentration Plant show that the BKJ special drum magnetite separators play an important role in increasing the concentrate grade and improving the economic benefit.

Jan 1, 2014

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

There is a strong demand for nickel metal due to quick development of stainless steel and new electrical materials, most of which is extracted from sulfide resources, resulting in a serious depletion of sulfide resources. Therefore, more attentions have been paying to extracting nickel from nickel laterite, which accounts for some 50% of total nickel metal production. In this paper prereducing?magnetic separation?reduction smelting process is developed to manufacture ferronickel rom two types of nickel laterite DN and GN, assaying 1.42% 1.83% Ni and 49.09% 26.08%Fetotal, respectively. Mineralogy of two types of nickel laterite was determined and optimization of process parameters was conducted to manufacture ferronickel. Prereduction?magnetic concentration process is used to upgrade low grade nickel laterite firstly, two kinds of Ni-Fe concentrates being prepared of DN assaying 2.26% Ni and 69.45% Fetotal and GN containing 2.76% Ni and 38.00% Fetotal. Finally, two types of ferronickel were produced by reduction smelting of prereduced concentrates DN and GN, DN and GN ferronickel contains 2.97% Ni and 6.58%Ni, 89.25%Fetotal and 89.95%Fetotal, respectively. The total recoveries of Ni and Fe of the two ferronickel are beyond 90% and 80%, respectively. There is significant difference in grade of magnetic concentrates and ferronickel between DN and GN laterite due to their different mineralogy, the former belongs to limonitic laterite and the latter saponite one. There are some advantages for this process to manufacture ferronickel from nickel laterite, including effectively upgrading low grade nickel laterite by prereducing?magnetic separation technique, higher throughput and lower energy available for reduction smelting section due to some 40% gangue being rejected in pre-upgrading section, and much less metallurgical coke consumption by using non-coking coal as reductant for prereducing?magnetic separation?smelting process.

Jan 1, 2014