Search Documents

By K. Gonçalves

One of Vale?s sponsored research project is aimed at the implementation of a practical scale-up procedure for flotation. In this context, detailed flotation kinetics characterization is of critical importance. This work presents the results of a campaign aimed at characterizing flotation kinetic parameters with respect to particle composition. MLA analysis was carried out for 40 narrow-sized iron ore particles with known flotation time from a controlled flotation kinetic test. The iron ore sample studied (59% hematite and 41% quartz) comes from a mine in the southeast of Brazil and the type of reagents applied are the same as used in the plant. For the reagent conditions tested, the overall rougher concentrate (sink) yielded 79.1%, pure quartz and hematite recoveries to the froth were 56.0% and 4.8%, respectively. The results from the kinetic tests show that the flotation rate of the particles doesn?t vary much (~0.03s-1) with composition and that the fraction of floatable particles in each grade controls the separation action. The results show that the rate of flotation is controlled by transport and that the selectivity is controlled by the fraction of floatable particle of each phase.

Sep 1, 2012

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By Baidyanath Mandal

Technology in the solid-liquid separation industry has evolved rapidly during the last fifty years and from the beginning, DIEMME Filtration has played a very important role in this evolutionary process by developing innovative solutions, which are used for a diverse range of industrial applications. Since the last decade, we find more and more examples of filter presses employed in the mining & mineral processing field, where high performances in terms of productivity, dewatering capacity and mechanical strength even in extreme working conditions are required. Mainly the requirement of such high quality equipment comes from the Process, however in few cases the reason could be linked with the environment. For stringent process applications like Mineral Concentrates dewatering & leached Slurry Filtration, it requires a high quality & extremely reliable equipment. In these applications, since many years industries are achieving the desired result by using Diemme Filter Presses. Also, recently, due to stringent environment practices are been applied globally, industries needs equipments which could dewater a high amount of residues / tailings with minimal moisture content in the filtered cake. In comparison to all the conventional dewatering equipments, Diemme Filter Presses are most efficient for these kind of product & applications. Diemme Filtration is a highly professional & technological company with several decades of experience in designing equipment for mineral processing. We take up each project as separate & design and manufacture equipment based on individual process or project requirement. This presentation will be focused on the Solid-Liquid separation technologies & equipment Diemme Filtration offers to the mineral processing Industries. It consists of Diemme?s History, Global Network, Technologies & Expertise, R & D Capabilities, Manufacturing Range, Some Applications & results on different mineral processing. Keywords: solid-liquid separation, filtration, dewatering, filter press

Sep 1, 2012

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By Kari Niiranen, Patrick Krolop, Viktoria Töyrä

Luossavaara-Kiirunavaara AB (LKAB) operates an iron ore mine, three beneficiation plants and three pelletizing plants in Kiruna, Sweden. The current methods of separation in the beneficiation plants are wet low intensity magnetic separation (WLIMS) and reverse apatite flotation, where the WLIMS stage is regarded as the crucial part of silica separation from the ore. Currently, the high-grade iron ore deposit of Kiirunavaara has a low grade of silica in situ, of approximately 3.0% SiO2, but the silica grade is expected to increase in the deeper parts of the deposit with a complex silicate mineralogy. An increasing silica grade will affect especially the production of direct reduction pellets (LKAB DR Oxide Pellets), one of the main products of LKAB in Kiruna with an average silica grade of under 0.75% SiO2. The silica grade in the magnetite concentrate is normally limited to a maximum level of 0.55% SiO2 in order to achieve the required chemical composition in the pelletizing process. In order to study the possibility to reduce silicate content in the magnetite concentrate (pellet feed) in the beneficiation plants in Kiruna obtained by wet low intensity magnetic separation (WLIMS), enlarged mineral processing test work was carried out in the LKAB’s mineral processing laboratories in 2016. The test work consisted of comminution, low intensity magnetic separation and reverse cationic silicate flotation at laboratory scale, complemented by screen analysis, chemical assays and mineralogical investigation. The results of these mineral processing test work showed that the magnetic separation is not sufficient to reduce the silica content in the magnetite concentrate, particularly in the case of the high-SiO2 ore type B2-a. The reverse cationic flotation can be regarded as a possible solution to reduce the silicate content in the magnetite concentrate obtained by WLIMS and to achieve the required silica grade of less than 0.55 % SiO2 in the pellet feed. The results of this study provide a good basis to understand the behaviour of different silicates in the existing beneficiation process. Furthermore, it serves valuable information for development of new beneficiation processes and for investment in new equipment at the beneficiation plants in Kiruna in the future.

Jan 1, 2018

By Shailin Lalloo, Allan B. Nesbitt

A fluidised bed was exposed to high gravities by placing it in a centrifuge. The bed expansions were measured and compared with the bed expansions predicted by the Richardson-Zaki model (1954). The Richardson-Zaki model was found to predict effectively the fluidisation behaviour of defined particles in this increased gravity environment.

Jan 1, 2003

By Paulo Sérgio de Oliveira, Joaquim D. Donda, Andreia C. Rosa

"The search for energy efficient technologies for comminution processes is constant in mineral processing studies, since those processes represent a major percentage of operational costs. In this context the use of stirred mills is increasing, especially for ultrafine grinding. Although many authors claim that these new equipment are more efficient than the conventional ball mills, there were very little chances to prove that in a practical way, since there are few industrial circuits where those technologies perform the same duty. Therefore, the regrinding circuit of Germano second concentrator offers an interesting opportunity: a vertical mill operating in parallel with two ball mills. During almost two years of operation, several sampling campaigns were conducted to evaluate the vertical mill performance and to compare the operational data of the three mills. The industrial data was also compared to jar mill tests results, which are monthly conducted in Samarco labs in order to predict the specific energy consumption required by the ore fed to these circuits. The vertical mill demonstrated the same ability to achieve the product specifications of the ball mills while proved to be able to reduce the medium specific energy consumption in about 40%."

Jan 1, 2014

By V. V. Trusova, Shiyrav Gandandorzh, K. V. Fedotov, V. A. Domracheva

"In Russia, 1.1 million tons of mercury-containing waste are stored. The amount of mercury in soils and heaps of industrial enterprises is estimated at 3000 tons; in dumps, concentration tailings, sludge dumps of the gold mining industry up to 6000 tons have been accumulated. Mining is one of the main sources of mercury emissions in the natural environment that poses a real threat to the natural environment. At present, the process of amalgamation is prohibited and not applied in gold extraction. The application of amalgam technology in gold mining led to the accumulation of highly toxic products in the form of gold-bearing amalgam and metallic mercury, with a mercury content of dozens and even hundreds of times greater than the maximum permissible concentration for soil (1). Therefore, mercury-containing tailings constitute an ecological hazard to the environment. According to published data, at waste storage sites of industrial enterprises, up to 50 tons of mercury enter soil annually, and up to 3.5 tons pollute the air. At the same time, mercury-containing waste due to the reduction of the country's mineral resources is an additional source of mercury. Therefore, it is necessary to recycle mercury-containing waste. INTRODUCTION Paperobjective: demercurization of technogenic raw materials (amalgamation tails, discharge outlets of tailing dumps) to be recycled. Under natural conditions, the mercury usually migrates in the form of three most common compounds: elementary mercury (Hg); mercuric mercury ion (Hg+2); methylmercuryion (Hg (CH3) +. Chemical compounds Hg (II) are found in natural conditions much more often than Hg (I).The authors propose to conduct demercurization of technogenic raw materials (mercurial tailings) in two stages. At the first stage, the mercury in the form of small balls, the finest particles (drip mercury) can be extracted by applying the gravitational method. We propose a method for centrifugal processing of crushed waste in the apparatus of Itomak company, Novosibirsk, as the basis of the technological process for mercury recycling. The extraction of metallic mercury out of mercury-containing waste into commercial products, according to the technological characteristics of the Itomak apparatus, reaches 86.0% (2, 3). At the second stage, the extraction of mercury out of technogenic raw materials is performed applying a sorption method and using carbon sorbents based on fossil coals. Hard coal of the Kuznetsk Basin has been already used for industrial production of active carbons (carbon sorbents) of the KAD-iodine type, which is one of the prerequisites that determine the choice to use it for the aims of this study."

Jan 1, 2018

By Fedotov Pavel

"Today the main objective of improving the process of ore dressing is to reduce energy consumption and performance of the basic rule of auxiliary enrichment processes. One of the modern means of ore destruction with a minimum of energy consumption is the interparticle fracturing, for example in the roller press. There still remain the unsolved problems of the energy consumption determination and the particle size distribution of the crushing product .Existing methods for determining these parameters are empirical and require considerable expenses and time. The improved finite element was developed to solve these problems using finite element contact interaction of the rock. Also it was developed to clarify the stress-strain and the rock fracture energy in a layer. These elements are used to study ore destruction in the layer and allows to create a model taking into account the interaction of crushing particles surfaces. The same algorithm was developed determining crushing product particle size distribution in the layer on the base of the Bond’s theory of crushing. The presented finite element model allows to determine the quantity of strain energy and particle size distribution of crushed product during the destruction processes of the material in the roller press with fair accuracy."

Jan 1, 2014

By Stoyan N. Groudev, Ioannis Paspaliaris, Irena I. Spasova, Kostas Komnitsas

"Acid mine drainage waters generated in the uranium deposit Curilo, western Bulgaria, were treated by means of a constructed wetland located in the deposit. The waters had a pH in the range of about 2.5 - 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, cobalt, nickel, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The wetland covered an area of about 140 m2 and was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Scirpus, Carex and Poa as well as different algae were also well present.The water treatment was started in July 2001 and until now (August 2002) the wetland effluents were characterized by pollutants concentrations decreased below the relevant permissible levels. The water flow rate through the wetland during this period varied in the range of about 0.2 - 1.0 l/s. The water clean-up markedly depended on the temperature but was efficient even in the cold winter months at air and water temperatures close to 0oC. The removal of pollutants was due to different processes but the microbial dissimilatory sulphate reduction and the sorption of pollutants on organic matter (viable and dead plant and microbial biomass) and clay minerals played the main role. Negative effects of the pollutants on the growth and activity of the indigenous plant and microbial communities were not observed."

Jan 1, 2003

By H. Koca, D. O. Aksoy, S. Koca

"In this work, modelling of galena flotation from a disseminated Pb-Zn ore containing 0,83 % Pb was investigated. In the flotation experiments, collector type and amount, frother type and amount, particle size, pH and flotation time were kept constant while solid ratio and depressant dosage were varied. The varied parameters are described with a mathematical model by using statistical design method. Central Composite Design method which is one of the principle response surface methodologies was used in statistical design and analysis of experimental results and process modelling. Two quadratic mathematical models were developed for Pb grade and Pb recovery. Analysis of variance showed that models obtained for Pb grade and Pb recovery were found to be statistically significant in 95 % confidence level. Predicted vs actual values of Pb grade and Pb recovery were also given in graphically. It was found that predicted values represent approximately 96 % and 94 % of actual Pb grade and Pb recovery, respectively. The high values of R-square (R2) indicate that the models developed for two response variables are powerful. INTRODUCTION Lead and zinc metals are widely used in electrical, mechanical, military, metallurgical, chemical, light and medical industries. Sulfide ores are the main resources for lead and zinc minerals (Luo et al., 2016). Froth flotation is the main beneficiation method to achieve lead and zinc sulfide minerals separation. There are two basic approaches to obtain lead and zinc separation by flotation. First, flotation of lead sulphide is carried out and zinc sulphide and gangue minerals are depressed by various depressants and second, the bulk flotation of lead and zinc sulphide is carried out to obtain a concentrate of lead and zinc, followed by the lead and zinc separation. (Yuan et al., 2012). Apart from concentration of lead and zinc by flotation, there are a few literature that reports concentrations of lead and zinc by gravity and hydrometallurgical methods with remarkable success (Goktepe, 2005; Yanbo et al., 2016)."

Jan 1, 2018

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTIONFroth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity.The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By M. Kalicinski, M. Lyssyy

"Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such real-time information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing case studies of their use in African and Australian iron ore and European steel, as well as a description of the potential benefits of a range of analysis equipment.INTRODUCTION Access to information is critical for any process, and is a fundamental component for making process control decisions. In order to yield effective processing outcomes, it is important for that information to be readily available, preferably as quickly as possible, and to be as accurate as possible. While speed and accuracy are often traded off against each other, there are numerous technologies available in a processing environment that allow for both rapid flow of information and a high level of accuracy. The use of on-belt analysis equipment has a long trusted history of use in a number of mining and processing environments and industries, providing information such as elemental composition and grade of conveyed materials, moisture content, waste proportion and energy information. Australian company Scantech has been a provider of such equipment since 1981, and has become an industry leader in both the supply and development of on-belt analysers across a range of industries."

Jan 1, 2018

By F. Bello, R. Yanez, M. Pinto, T. Errazuriz

"Throughout its operation, Minera Esperanza (ME) will deposit one of the largest tonnages rates of high density tailings in the world with a solids concentration of close to 67% by weight. The tailings presently being deposited have a solids concentration of approximately 62% - 64%, and so cannot be used to directly characterize the flow and deposition characteristics of the higher concentration tailings. To increase the knowledge of the behaviour of their tailings, ME, with the support of Golder Associates, developed a large scale tailings deposition test with a capacity of 30,000 tonnes per day (1,200 m3/h). The test was carried out by depositing tailings into two large cells or paddocks in five stages. Multiple spigots were used to allow different flows to be deposited. At each stage, topographical surveys of the natural terrain and the geometry of the deposited tailings, as well as continuous flow measurement and periodical rheological characterization of the discharged tailings were conducted to create a data set against which beach slope models could be calibrated and then used to predict performance of the higher concentration tailings under different deposition scenarios. This study adopted the beach slope prediction model proposed by A.L. Li (Li, 2011). The model was successfully adjusted to the observations made during this large scale field test by applying the values measured in-situ. This paper presents the application of the model, the results obtained, the findings, and the analysis of possible future scenarios. The model was applied, using the discharge flow rate, the geometrical characteristics of the discharge area, and the rheology with its variation along the beach to estimate the development of the beach formation and the steady state of the beach slopes. Through the use of dimensionless variables, the model was applied to higher solids concentration scenarios, obtaining results that would allow beach slope estimation at different deposition stages in multiple scenarios of varying parameters such as flow, rheology and geometry of discharge area."

Jan 1, 2014

Calcium sulfate whiskers are considered to be a prosperous reinforced material in application due to their high mechanical properties. But the hydration occurs easily at moist atmosphere or in aqueous solution. The surface topographies of the calcium sulfate hemihydrate whiskers and the hydrates were analyzed by on-line observation and using XRD. The results indicated the transformation of the crystal type and shape of calcium sulfate hemihydrate whiskers and the reduction of whiskers? aspect ratio. The hydration process of the calcium sulfate hemihydrate whiskers and the effective parameters were further discussed based on FT-IR measurements. The conclusions were obtained that the hydration of calcium sulfate hemihydrate whiskers can be divided into the three phases, namely, initial hemihydration phase, dehydration phase, and coarsening, dissolving and the re-formation of calcium sulfate dehydrate crystal phase. In addition, it was found that in the hydration process of calcium sulfate hemihydrate whiskers the calcium sulfate dihydrate whiskers are formed at first and then converted into the calcium sulfate dihydrate with different crystal shapes, but in the hydration of gypsum hemihydrate the gypsum dihydrate is formed without transition products. The surface active site-calcium ion which has strong trend to react with H2O, the surface ?OH and the inner channels are considered to play important roles in the hydration process of calcium sulfate hemihydrate whiskers.

Jan 1, 2014

By Christopher Davey, Professor Emeritus, Marian Mazurkiewicz, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of sub-micron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill’s chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydro-wedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003