Search Documents

By George K. Burke

Underpinning of a structure has been traditionally expensive, time consuming, and, in many cases, caused as much settlement to the existing structure as it was trying to prevent. As underpinning is normally one of the initial tasks and on the critical path on a construction project, there is immense pressure on the subcontractor to speed up his operation so the new structure can proceed; this can cause an adversarial relationship to develop between the owner, engineers, general contractor and subcontractor. Since its introduction to the North American market in the late 1980's, Jet Grouting has not solved all these problems, but where utilized, has shown economical benefits, a faster and safer installation, and a minimal movement of the structures being underpinned. A history of the development of jet grouting is presented; a comparison of this technique versus other grouting methods, a description of the jet grouting system with emphasis on the triple rod systems; case histories of jet grouting used for underpinning and conclusions and references are included to follow the program's themes of: - Recognizing Solutions to Today's Problems - Defining Tomorrows Challenges - Putting America on a Solid Foundation

Jan 1, 1991

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

By Emad Farouz

The resistance of very dense glacial outwash formations consisting of sand, gravel and cobble formations can be quite high, and techniques for measuring the strength and deformation properties often cause engineers to underestimate the strength of these layers in drilled shaft design. More realistic measurements of this dense formation can be achieved with slotted steel casing pressuremeter tests. To minimize disturbance and achieve accurate measurements, drilling a pilot hole prior to probe insertion is necessary. Characterizing geologic formations that contain significant amounts of gravel and cobbles is challenging because of scale factor. Inserting a standard pressuremeter probe into this formation without damaging the membrane is difficult. This paper presents a case study for the IR-75 project in Dayton, Ohio, USA, where these dense materials were characterized using a slotted casing pressuremeter, optimizing design by providing more realistic properties of these materials.

Jan 1, 2006

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By H. L. Jessberger

In recent years piled raft foundations of multi-storey buildings on weak soils have generated much interest and discussion. By taking account of the effects of each component of the system - the pile group and the raft - it is possible to reduce the settlements and inclinations of the system and to have an expedient load distribution on the piles and the raft. Thus the structural design of the foundation can be optimised.

Jan 1, 1991

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017

By Z. Q. Zhou

It is the first worke in design of pile foundation to determine the carring capacity of single pile, and a static loading on site is considered to be the lost derect and reliable way. All values P and settlements S induced can be plotted as a broken-line. Since soil is a kind of elasto-plastic and cohesive material, the increasing of settlements is generally greater than that of loads. Different value Pu nay be given by different tester on his P-S diagram, because of erroys in the test and complicated, characteristics of soil. The analytical method of exponential equation shown in this paper derives a specified solution. After using an exponential curve to regress values of loads P and corresponding settlements S from on-site test, coeficients A and B of exponential equation can be obtained. With this curve an ultimate carrying capacity of single pile can be determined. The resistant forces of pile shaft and pile tip can also be defined by the tangent of the calculated knee point, as it is called (tangent method). At last, an example is given to show how the ultimate carrying capacity of f 500mm bored pile is obtained with this method for a project in Kunming.

Jan 1, 2010

By Thomas C. Anderson

Tiedback walls are now recognized and accepted as a good solution for a variety of structural problems: ? Retaining Walls and Bridge Abutments in cut situations ? Landslide stabilization ? Repair/support of existing walls Acceptable techniques have been developed for anchoring in cohesive and granular soils and in any kind of rock. Methods have been developed for adequately protecting tieback tendons against corrosion and for testing every tieback to verify its long-term load-carrying capacity. However, the major problem that the industry faces today is how do we get constructable and economical tiedback walls contracted for and built with minimal claims. This paper will explore the issue of "constructability" through a look at specific problems from actual projects. From a research report from the Construction Industry Institute, Austin, Texas (1986), constructability is defined "as the optimum use of construction knowledge and experience in planning, design, procurement and field/operations to achieve overall project objectives." Maximum benefits occur when people with construction knowledge and experience become involved at the very beginning of the project." The design and installation of tiebacks has been developed primarily by specialty contractors; each contractor has evolved its own methods of performing the work, and consequently, many of the techniques are patented and proprietary. The real question is, how do we make effective use of this knowledge and experience during the design phase of the project?

Jan 1, 1991

By Richard T. Stain

"In 2001, a pile trial site was established at Limelette in Belgium consisting of 25 displacement screw piles and 5 driven pre-cast piles. Interested parties were invited to participate in a pile prediction event, whereby they would submit predicted static load test behaviour in the form of load settlement plots. These predictions could be based on soil investigation results supplied by the organizers, or dynamic load test measurements.Following the submission deadline, the organisers released the results of static load tests for comparison.Of all the six participants, including Statnamic, the SIMBAT method was independently accredited with achieving the best predictions.This paper examines at the differences between SIMBAT and other systems, and presents the correlations from the Limelette trial.INTRODUCTIONThe Belgian Building Research Institute (BBRI) initiated an ambitious research programme involving the construction and testing of some 60 trial piles spread between two sites, a clay site at Sint Kateline Waver and a sandy site at the BBRI headquarters at Limelette. The project was financed largely by the Belgian Ministry of Economic affairs. (ref 1.) This paper refers only to the second site.At Limelette, six different types of displacement pile were installed: one driven pre-cast and five cast in place screw piles - Atlas, DeWaal, Fundex, Olivier and Omega. A detailed site investigation was carried out including in-situ and laboratory tests.An international pile capacity prediction event was publicised, participants being invited to predict static pile behaviour. Predictions could be based on:"

Jan 1, 2005

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018

By Jamey B. Rosen

As Project Information Management Systems (PIMS) technologies develop, the range of projects to which one can apply these technologies grows while the cost to apply them shrinks. In recent years, technologies previously limited to large “megaprojects” (e.g., major dam rehabilitations) owned by major entities (e.g., the United States Army Corps of Engineers) with large budgets have been applied to smaller projects with less stringent specifications and more modest budgets. This paper will describe applications of PIMS technologies to small projects with limited budgets, including examples from levee construction, small-scale grout curtain installation, and diaphragm and secant pile cut-off walls. We will include a demonstration of how PIMS technologies can effectively analyze verticality data from koden and hydromill data streams to automatically generate models and as-built drawings showing overlap and deviation along the depth of the foundation. INTRODUCTION This paper discusses the application of Project Information Management Systems (PIMS) technologies to geo-foundations projects, with a focus on technologies and examples that are in a lower cost range. PIMS technologies allow contractors and other stakeholders to perform efficient quality control on their data, generate quick or automatic reports and as-built drawings, perform analyses to better understand their construction, and ultimately use their data to increase the quality of their construction. As PIMS technologies are relatively new to the deep foundations industry, and owner specifications on their use are generally viewed as complex and limited to large scale projects, PIMS technologies are frequently viewed as an expensive component that is beyond the scope of a smaller or simpler project. However, the same principles and techniques generally associated with large projects can be applied to projects at smaller scale. Furthermore, as these technologies develop both in the deep foundations and other industries, the cost of application is decreasing quickly making them even more affordable for smaller projects. The remainder of this paper provides some justification for applying PIMS technologies, describes some scalable data management concepts and workflows and then provides some examples of “low cost” applications of these technologies.

Jan 1, 2019

The pile inspector is a critical element in the quality control process necessary for a successful pile installation project. This guide is intended to provide the inspector with a basic understanding of only one of the many components of this process - the pile driving hammer. Pile driving hammers are used to install both bearing piles for structure foundations and sheet piles (and soldier piles) as used in retaining structures. In a single document, this guide offers a general presentation of the operation of the more common types of hammers the inspector is likely to encounter. It should make the information in the contractor's hammer submittal for the project more understandable. It should also provide an appreciation for the importance of a properly operating pile hammer. Prior to the start of most pile driving operations, the contractor will normally furnish a submittal to the engineer giving the specific pile driving equipment that he intends to use on the job. This submittal should include the make, model, and type of the intended pile driving hammer or hammers and their operating characteristics such as ram weight, rated energy, operating speed, external power requirements and, other pertinent information. Frequently, the operating characteristics are provided in the form of the manufacturer's specification sheet. The engineer will review this information and when he is satisfied, approve it and pass it on to the inspector. The driving criteria will have been determined by the engineer or others (the geotechnical engineer, consulting engineer, contractor, etc.) from the results of static analysis (for minimum penetration), driving during a test pile installation, Wave Equation analysis, dynamic formula, pile instrumentation during driving, static load test, or a combination of these or other appropriate analyses. The driving criteria can be a minimum penetration of driven pile length (embedded length), or a minimum (or maximum) blow count per unit of penetration. The pile inspector should become familiar with this information prior to the start of the job and should understand or seek help to comprehend the terminology and intent of each specification.

Jan 1, 1995

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992