Search Documents

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By John N. Cunningham

Despite the wide use of micropiles for rehabilitating and retrofitting existing structures, little is known regarding the load-transfer distribution of grouted micropiles in various soil deposits. The rehabilitation of a concrete-frame warehouse in Portland, Oregon, required provisions for the seismic restraint of a new shear wall; the installation of two micropiles was specified to meet project requirements. The micropiles were uncased, 19-m (63-ft) long, 200-mm (8-in) nominal diameter, and reinforced full-length with a 64-mm (No. 20) diameter hardened steel threadbar. Due to space limitations, a sacrificial, instrumented micropile was installed near the two production piles to verify design assumptions. This paper describes the geologic setting of the project within the unsaturated Missoula Flood deposits, instrumentation, load-displacement behavior, load transfer, and Beta-coefficients for the sacrificial micropile.

Jan 1, 2011

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By Hessam Yazdani

In comparison to the conventional piled foundations, the piled-raft foundations provide a more economical solution to support high-rise buildings constructed on soft soils. In this type of foundations, the bearing capacity of the underlying soil is taken into account to support the superstructure loads and the piles are placed to control both the total and differential settlements of the superstructure. Currently, there is not a standard and worldwide acceptable approach to select the location of the piles and most of piled-raft foundations are designed based on the experience of designers. Therefore, particular attention should be given to the optimal design of this type of foundations in order to minimize the considerable construction costs involved. This paper examines the capability of the ant colony optimization (ACO) algorithm to optimize the piled-raft foundations subjected to static and seismic loadings. The soil-pile interaction is considered by modeling the side and tip resistance components of the piles using the nonlinear Winkler-based p-y and t-z curves in the OpenSees program. The soil-raft interaction is taken into consideration using the Winkler springs beneath the raft. The objective of the optimization problem is to minimize the construction cost of the foundation by taking the configuration and number of the piles as design variables. The side and tip forces of the piles as well as the total and differential settlements of the foundation under the serviceability limit state are considered as the constraints for the optimization problem. Results show that in addition to the type of analysis (linear/nonlinear), the regard or disregard of the soil-pile interaction in the analysis can significantly change the optimal solution. The optimal solutions obtained match the engineering expectations and indicate the effectiveness and capability of the ACO algorithm to minimize the construction cost.

Jan 1, 2013

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984

By Joan Stoupa

The expansion of the West Point wastewater treatment plant located in Seattle, Washington, will require a permanent tieback retaining wall to enlarge the plant site for the new treatment plant facili­ties. The retaining wall will extend approximately 3,000 feet along the property boundary between the treatment plant and the neighboring Discovery Park. Wall heights will range from 35 to as high as 65 feet. The purpose of the retaining wall is to provide a more uniform grade on the plant site and to resist lateral pressures exerted by the upslope, unstable hillside. During preliminary design of the retaining wall, various wall systems were evaluated based on assumed subsurface soil conditions. Results of preliminary studies indicated that expected subsurface conditions and wall heights made a permanent tieback retaining wall feasible. However, uncertain loads on the wall and the capacity of anchors in the native soils were significant. As a result, a detailed geotechnical program was conducted. The scope of the program included conventional drilling, sampling, analyses, and a field test program to determine site-specific anchor capacities. This paper describes the anchor test program and results.

Jan 1, 1990

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

Jan 1, 1994

By Ekhlaq A. Khan

"The new third Bridge over Narmada River at Bharuch which was recently completed is characterized by some aesthetically appealing elevations of the pylon and large size of the deck. This paper gives an insight to design and construction technique adopted for foundation construction of Extra-dosed span - 3 rd Narmada Bridge at Bharuch over river Narmada, Gujarat. Site being located in intertidal zone had its unique geological characteristics and own set of difficulties during construction.INTRODUCTIONThe Indian subcontinent offers diverse subsoil conditions. With current modern and future trend of long span bridges the substructure design often demands large size foundations. The foundation of theses bridges are usually deep and large in size. The execution of such foundations in maritime environments often involves important temporary works, in order to provide a safe workplace, comply with environmental requirements and achieve high quality standards.Often Pile foundations are preferred solution now a days, but due to various statutory and environmental regulations their construction poses a challenge. With better equipment and corresponding quality control, construction of large diameter pile foundation has emerged as a faster and reliable option.OVER VIEW OF THE PROJECTThe first two lane bridge on NH-8 (Vadodra – Mumbai) known as Sardar Bridge was constructed in 1977, subsequently an additional two lane bridge was constructed in 1999-2000, 29 m downstream of the first. In view of rising volume of traffic and as part of upgradation of NH8, National Highways Authority of India (NHAI) proposed to construct 3rd new 4 Lane Bridge 100 m downstream of 2nd Narmada Bridge, based on Central Water and Power research Institute (CWPRS) study and recommendation.The general layout (fig. 1) of the 3rd Narmada bridge has 8 spans of 144 m and 2 spans of 96 m with total length of 1344 m, supported by132 nos. of 1.5 m diameter piles of about 50 m depth. The substructure has leaning “Y” shaped lower pylon of height 30 m together with cast in situ pier diaphragm. The piles are of M40 and superstructure & pylon of M50 grade of concrete."

Jan 1, 2017

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014