Search Documents

By Y. G. Qin

In this article an experimental study of axial bearing capacity of half-closed steel pipe pile installed at BKSH dock is presented. In comparison with open and closed end piles, half-closed end pile is considered to have high bearing capacity and good penetration, that is, it not only has a capacity as twice as the same size open end steel pipe pile, but also has blow counts as half as the same size closed end steel pipe pile. It is economic to use half-closed end pile in soft ground without a deep deposit of thick stiff clay. This article also describes a large scale model pile test and preliminarily analyses mechanism of improvement of bearing capacity of half-closed end pile with emphasis on effect of squeezed soil on side friction; an empirical approach is presented in which side friction is related to density of squeezed soil and which is useful for reasonably chosing side friction of different types of piles in design of foundarion.

Jan 1, 2010

By Javaid M. Alvi

This paper is an attempt to outline the emergence of Augered Cast-ln-Place piles as one of the more economical types of foundation for supporting high-rise buildings and heavily loaded structures recently constructed in the flood plains in and around the Greater Pittsburgh area. To understand the process of selecting foundation types, it is important to understand the general geology of the area and past construction activities that have taken place in the flood plains, especially along the riverbanks, during the last century. The first part of this paper presents a brief description of the general geology of the area; the second part of the paper concentrates on the historical evolution of the use of deep foundations and selected case histories; and the last part presents the results of load tests on large diameter Augered Tremie Concrete (ATC) Piles placed in sandy alluvium which suggests a much larger load-carrying capacity of these piles and also provides an insight into their future application. 2.0 GENERAL GEOLOGY 2.1 Soil Overburden Most of the high rise buildings in the Central Business District as well as along the North Shore and South Side of Pittsburgh are situated in the flood plain at the confluence of the Allegheny River and the Monongahela River where their combined flow forms the Ohio River. The flood plain consists of unconsolidated deposits of Quaternary age that overlie the bedrock of Pennsylvanian age. These deposits are called alluvium or valley fill, and include moderately to poorly sorted clay, silt, sand, gravel and some boulders. Their thickness varies from zero at the edges of the valley to about 80 feet towards the rivers (Figure 1).

Jan 1, 2001

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity. Now this important project is in progress and this report describes the special foundation techniques used on the great ship lock Hohenwarthe. Hohenwarthe is a double- bay ship lock of considerable scale, which is notable for recirculating water rather than letting it flow. It includes 44 800 m2 ( 481 720 sq. ft) of up to 55 m ( 180 ft) deep cut- off walls, ground water control, 1248 bored piles with a depth of 22 m ( 72 ft ) serving as foundation and 28 000 m ( 91 864 ft) of soil densification with vibroflotation equipment for ground improvement. In the year 2003 the project shall be completed and all ships can travel from the West to the East through Germany without expensive and time- consuming detours through other canals and locks.

Jan 1, 2000

By Osama Safaqah

The new Cooper River Bridge will replace two existing bridges along U.S. Highway 17. The cable-stayed bridge will be one of the largest in the U.S and will connect the City of Charleston and the town of Mount Pleasant, South Carolina. The 1,546-foot long main span over Cooper River is supported by two diamond-shaped towers and will allow for 1000-foot wide navigation channel. The Charleston high-level approach is approximately 4351-foot long and will provide 250-foot wide navigation channel over Town Creek, while the Mount Pleasant high-level approach is 2090-foot long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. Among various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against lateral loading. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies coastal sediments of interbedded clays and sands. The main towers will be supported on a group of 11 shafts and protected from ship collision by a rock island. The High Level Approach piers will be supported on a pair of 2 shafts. The shaft tip elevation is up to 230 feet below water line. An elaborate geotechnical investigation has been conducted on the site including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2005

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By Jesse A. Pfeiffer

CPAR, the Construction Productivity Advancement Research Program, is a new initiative of the Corps of Engineers to enhance U.S. construction industry productivity through the development and application of joint-funded research. CPAR seeks to balance the requirements of both the private sector and the Corps of Engineers construction program, to identify research needs that are common to both parties in a partnership for conducting research, and to achieve practical real-world products which will enhance productivity in the construction industry. Increasing costs of doing business has had a major negative impact on much of the nation's industrial base, and research and development (R&D) is among the areas hardest hit. The Congressional Budget Office estimates that since 1984 inflation adjusted R&D outlays in private U.S. firms have risen at an average annual rate of three percent, or about half the rate of gain of the preceding decade. And, despite a significant increase in foreign competition, the portion of gross national product (GNP) devoted to R&D is lower today than 20 years ago. For the case of the U.S. construction industry, the numbers are even more dramatic.

Jan 1, 1989

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By Franz-Werner Gerressen

"The use of soil improvement to utilize areas, which are not suitable for foundation purpose, has a long tradition. Due to the increasing demand of foundation works in areas of unsuitable soils, the improvement of the existing soils becomes even more important in the future.Various applications and systems for various demands exist around the world. Either it is a “simple” improvement for settlement reduction or a more important aim as liquefaction mitigation. However, each system has its advantages, limits and needs.Furthermore to the soil improvement, using various tools, soil mixing can also be used for applications like cut off and/or retaining wall.The paper will describe some basics of various techniques and different applications of the systems all over the world where the systems provided solutions for different purposes, e.g. simple foundation or liquefaction mitigation.It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONSoil mixing is a methodology where the soil is improved by mixing it with cement, lime or other binders in situ by using a mixing tool. This methodology can be used either as wet mixing or as dry mixing. In the more frequently used wet mixing process, usually a mixture of binder and water, maybe with additives, is injected and mixed with the soil. Depending on the type of soil and binder, by the end of the mixing process, a mortar like mixture is created which hardens during the hydration process. In the dry mixing process, the binder is directly mixed with the soil and reacts directly with the existing soil and water.Mixing tools show several versions, so that they are mixing around either a vertical or horizontal axis, mixing in a trench and maybe are jet assisted. Figure 1 shows a classification done by Bruce 2010. Depending on the technique, improvement depth of up to 80 m can be achieved."

Jan 1, 2017

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001