Search Documents

By W. P. Tassie

"The location of Quintette Coal Limited's pit and geologic nature of the dedicated reserves combine to introduce a number of factors which can adversely affect waste dump stability. These factors include steep terrain, variable material type and particle size, and precipitation. This paper describes the solutions to related waste dump problems. A brief geotechnical review of the waste dumps is given and Quintette's operational strategies during periods of dump stability and instability are discussed. Despite best efforts, failures occasionally occur and discussion is included on Quintette's success at bringing failed dumps safely back into use. IntroductionQuintette Coal Limited (QCL) property is situated on the east slope of the Rocky Mountains near Tumbler Ridge, approximately 120 km southwest of Dawson Creek, British Columbia. This surface mine is located on mountainous terrain and is subject to climatic extremes of wind, precipitation and temperature.QCL has a current annual production of 4.75 million tonnes of metallurgical coal with a stripping ratio of 7: 1. This correctly implies the extraction of over 33 million bank cubic metres (BCM) of waste which is placed on numerous waste dumps at various locations adjacent to the pit.There are three active pits - Mesa, Wolverine, and Shikano (Fig. 1). Shikano is a newly developed pit located near the plant site. It is not subject to the unique dump management problems prevalent at the Mesa and Wolverine pits, therefore the Shikano waste dumps will not be discussed . The dumps for the Mesa and Wolverine pits, however, have been technically and operationally challenging since shortly after mining began in 1983. Their characteristics, associated site specifics and management, therefore, are the subject of this paper.Waste dump locations for the Mesa and Wolverine pits are shown in Figures 2 and 3 as is the relative waste distribution . Each sub-pit is connected to a principal waste dump in reasonable proximity and to an alternate dump should disposal of waste be necessary at that location. The waste dumps are constructed from the top elevations initially to coincide with subpit development. In the initial years (1-7) waste dump heights will be up to 250 m, then, as the mine matures (8-20 years), waste dump maximum heights will continuously decrease to coincide with lower bench elevations"

Jan 1, 1988

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By Oyku Selimoglu

The key to successful mine production plan and subsequent operation is efficient mine layout design and optimization. Pit layout design and optimization allow the delineation and extraction of mineable reserves and the minimum waste subject to slope stability, economic, quality and quantity constraints. Many design and optimization software packages have been developed to aid this intensive and challenging process. These packages include VULCAN, SURPAC, DATAMINE, GEMCOM, MICROLYNX, MEDSYSTEM and MINESIGHT. These software packages are developed as integrated computer-aided systems used for database creation, survey, geological and geostatistical modeling, mine planning and production optimization and environmental modeling. In Turkey, many mining companies still plan and design mine layouts with traditional hand methods. In this study, VULCAN has been used to design and optimize the Eti-Bor A.S. Kestelek Boran Open Pit Mine in Western Turkey. The main objective is to show the company the superior advantages of mine planning software for designing and optimizing mine layouts over the traditional hand methods. Drill hole data used by the company to estimate the reserves for planning are used in this study. The ore grade varies between %1,04 B2O3 to %47,33 B2O3. The pit toe and crest strings are projected using variable batter angles and berm distances. On the north side, batter angle is 180 and berm distance is 25 meters, on the south side, batter angle is 320 and berm distance is 15 meters. In addition to that open pit bench height is 10 meter. The concepts of block modeling are applied to the Kestelek open pit mine with detailed ore grade modeling for each block. The Lerchs-Grossmann?s algorithm is used to optimize this mine based on the block model, the economic block values for each block and the underlying field constraints. The results from VULCAN were similar to the estimates by hand. The reserve estimates from VULCAN is 13,192,870 tons compared with the hand estimate of 13,200,000 tons, overburden estimates of 15,622,889 m3 compared with 15,000,000m3 obtained by hand with a stripping ratio 1.18:1 (m3:ton) from VULCAN versus 1.14:1 (m3:ton) from hand estimate. Vulcan improves the efficiency, speed and reproducibility of the planning results. It provides mining engineers, geologists and surveyors with a cost-effective modular system for assessing and planning the mine layouts. Furthermore, Vulcan?s specific modules allow efficient access and manipulation of databases, open pit mine design, block models, optimized 3D mine layouts, and more. However, for competitive business in Eastern Europe, VULCAN should improve its software support. Effective training, help desk support systems and nearby distributors with just-in-time solutions to company problems will generate competitive business for VULCAN.

May 1, 2007

By E. H. Smith

"The El Indio mine treats a complex mixture of copper and gold/silver ores at its plant located in the high Andes in Chile. The plant utilizes conventional crushing, grinding and flotation to produce a copper/gold/silver concentrate. Due to high levels of arsenic and antimony, the flotation concentrate must be roasted prior to custom smelting. The flotation tailings is leached and additional gold recovered from a CIP circuit. Present and future metallurgical developments are discussed in this paper. INTRODUCTIONIn late 1989, LAC Minerals purchased 65 % of Bond International Gold and as a result became controlling shareholder of the El Indio Mine through Bond and San Jose.El Indio is a world class, complex sulphide gold deposit located in the hydrothermal alteration belt of the Andes mountains in the 4th Region of Chile. The mine is located in the high Andes about 185 km east of La Serena at an elevation of 4000 meters. The 1450 workers at El Indio live in the mine camp at 3200 m and on days off are bussed to La Serena.The El Indio mine was started in 1979 by St. Joe Minerals Corp., bought by Bond in 1987 and subsequently by LAC in 1989. The mine has produced 2.7 million oz. of gold, 9.5 million oz. of silver and 170,000 t of copper since start of operation. The mill is currently operating at a rate of 2850 t/d and producing a copper/gold concentrate which is roasted to produce a copper/gold calcine and high quality, saleable crude AS2O3 . A small proportion of the precious metals are also produced as bullion from the leach circuit.Total production during 1989 was 224,197 ounces of gold, 1,309,342 ounces of silver and 26,968 tonnes of copper. The average cash cost of production for the period was U.S. $96 per ounce of gold, net of by-product credits. The average realized price was $5. 30 per ounce of silver and $1.14 per pound of copper."

Jan 1, 1991

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

By Martin Nevens

"In 1998, the Iron Ore Company of Canada initiated an aggressive program to improve the performance of its Carol Lake Concentrator located in Labrador City, Newfoundland. This program was termed the Concentrator Upgrade Program. The Concentrator Upgrade Program was a group of initiatives developed with the common goal of improving the overall process and operations of the IOCC Carol Lake Concentrator. The main goal of the program was to increase the annual production capacity of the concentrator from 18.0 million tomes to 21.6 million tomes. This gain in capacity was to be done mainly through improvements in process iron recovery. The target iron recovery value was 80+% versus a historical value of 70%. This improvement in iron recovery would translate to a natural weight recovery improvement from 44% to 50%.The Concentrator Upgrade Program provided the first opportunity in 30 years to make fimdamental changes to the concentrator flowsheet. To accomplish this, several pilot plants were built to evaluate new circuits. AAer 2 years, a new flowsheet was selected for the primary gravity separation circuit and the magnetite circuit. The centrepiece of the new flowsheet was the introduction of Hindered Settling Separators to the metallurgical process.The Concentrator Upgrade Program has since proceeded into detailed engineering and, as of February 2001, construction. The first one of IOCC’s 3 primary AG Mills (Mill 11) has been converted to the new flowsheet at the time of writing and is in the throes of commissioning. This paper will review the flowsheet development program in the pilot plant for the gravity separation circuit and examine the overall benefits to the operation of the IOCC Carol Lake Concentrator."

Jan 1, 2002

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008

By L. Lui, A. Cauchon, A. R. Laplante

"The gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30"") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18/30 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size-by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 µm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution. INTRODUCTIONBackgroundThe operating performance of the mill of Les Mines Camchib Inc. has been described earlier (Laplante et al., 1989). The presence of significant chalcopyrite (1 % and up) makes flotation necessary prior to cyanidation, to limit cyanide consumption and minimize environmental impact. In 1982, the presence of very high gold circulating loads in the grinding circuit lead to the commissioning of a gravity circuit, schematically shown in Figure 1. Gravity recovery of gold has been found beneficial because it increases metallurgical recovery by 1-3% (Laplante et al, 1987), as only part of the flotation tail is cyanided, and economic recovery, because of the lower net smelter return of gold in the flotation concentrate (as compared with the gravity concentrate). The latter increase is estimated, with a net smelter return of 95%, at 1.5% when gold recovery by gravity is equal to 30%. In early 1988, a sampling program was initiated to characterize the behaviour of gold in the grinding/gravity circuit. This paper reports on the results of this study."

Jan 1, 1990

By R. G. Hamm

A brief outline covering the shovels and draglines in use in the open-pit mines of Western Canada, including British Columbia, Alberta and the Yukon, is given, followed by the procedure for the selection of the correct wire rope for each application. Such fa ctors as wire rope constructions, lay directions and types of cores are mentioned. Once the correct wire rope has been selected, there are variousfactors that can affect the service fife ofthe rope and the reduction ofdown-time during rope change-overs. Factors such as hairpin winding, types of Becket loops, and shovel drum and bail adaptors are described.

Jan 1, 1979

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By M. Fan, M. Mankosa, G. Luttrell

"Column and other non-conventional flotation approaches continue to provide benefits where conventional flotation processes have exhibited limited success. This is particularly evident with respect to flotation of ultrafine and coarse particles. Advancements in air sparging technology have provided the ability to produce finer bubbles than previously possible. The generation of finer bubbles coupled with the froth washing capabilities of a flotation column has demonstrated improvements in ultrafine particle recovery while simultaneously producing a high-grade float product. On the other side of the spectrum, the use of these sparging technologies while applying flotation fundamentals to a fluidized-bed reactor has increased the maximum floatable particle size up to and in excess of 3 mm. Benefits of higher recoveries and reduced reagent consumption have resulted from the use of these technologies. An additional benefit includes a reduction in plant grinding requirements. As such, this paper describes the application of Cavitation-Tube sparger technology and fluidized-bed flotation (HydroFloat). A review of data from industrial and pilot-scale applications is also provided.INTRODUCTIONConventional (mechanical) froth flotation is considered the workhorse of the minerals processing industry. This low-cost process makes it possible to selectively recover minerals by exploiting the difference in surface characteristics (e.g., wettability) of the valuable component and the waste material. Unfortunately, the upper particle size limit for flotation rarely exceeds 0.600 mm, and is typically maintained at less than 0.300 mm for most industrial applications. For many commercial base metal plants, the particle size range for optimum recovery is typically between 0.01 and 0.1 mm (Lynch et al., 1981). This finding is not novel. In fact, the effect of particle size on flotation recovery was studied as early as 1931 by Gaudin et al. who showed that coarse (+0.250 mm) and extremely fine particles (-0.010 mm) are more difficult to recover than particles of an intermediate size. The loss of recovery is due to inherent limitations associated with the flotation process, including bubble-particle adhesion and collision, detachment, buoyancy, and transport."

Jan 1, 2010