Search Documents

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By Angeles Mendoza Sammet

Based on the analysis of issues associated to conflicts between communities and mining companies in Mexico, this paper suggests actions to make mining more sustainable in Mexico. Interviews with key informants and a revision of documental information available on the internet provided information on 15 cases of conflicts in various parts of the country. The issues varied from incompliance with environmental law to assassination of community members opposing mining. The analysis concludes that mining is not sustainable in Mexico. Both mining companies and the Government of Mexico can make changes to improve sustainability. Mining companies could take a proactive approach and engage in consultation with communities before starting operations. Sharing information with communities on environmental management programs and monitoring results can be a way to start building trust and demonstrate environmental commitments. Companies can implement and evaluate CSR policies to ensure that all staff and contractors are trained on them to reduce and/or prevent corruption and violations of human and indigenous rights. Only 3 of the 15 companies had clear social responsibility policies or sustainability targets, but no reports evaluating them. Complying with the law does not make a project sustainable because of corruption, deficient enforcement, and gaps in legislation. The Government of Mexico should address the following points to make mining more consistent with sustainable development. Update the mining legislation to introduce sustainable development principles and consultation. Incorporate the notion of Free, Prior, Informed Consent (FPIC) for Indigenous People (IP) on all applicable Mexican laws or regulations. The government should not grant concessions on protected areas or indigenous lands without extensive meaningful consultation with the public, IP and land owners. Finally, it is vital to increase SEMARNAT?s capacity to review impact assessment reports and inspect and monitor environmental compliance along the life cycle of projects.

Aug 1, 2013

By Mike Power

Geophysical techniques have played a pivotal role in northern kimberlite exploration since the initial discovery at Point Lake in 1991. In the Slave Craton and surrounding regions, there are definite contrasts in physical properties between kimberlite intrusions and surrounding bedrock. Kimberlite commonly displays higher magnetic susceptibility, distinctive remnant magnetism, low electrical resistivity and lower density than surrounding rocks. In addition, the distinctive geometry of kimberlite pipes is reflected in geophysical responses which further facilitates target discrimination. There has been an evolution in geophysical exploration strategies over the past 12 years. Helicopter total magnetic field and electromagnetic (HEM) surveys have proven to the most cost-effective means of conducting first pass investigations in prospective areas. During the early 1990's, total magnetic field and frequency domain electromagnetic surveys were virtually the sole techniques employed during follow-up surveys. Inevitably, the initially high rates of kimberlite discovery declined in the areas surrounding the original finds. Marginal magnetic and EM anomalies were all that remained to be tested and this spurred interest in the improvement of existing interpretation algorithms and in the application of additional complementary techniques to reduce the exploration risk. Gravity has become a popular third survey following the deployment of the Falcon (TM) airborne gravity gradiometer system by BHP Billiton in 1999 and improvements in ground techniques. Ground penetrating radar (GPR) has proven to be particularly useful in delineating kimberlite pipes following drill discovery and in exploring for kimberlite dykes in settings where indicator mineral trains indicate such targets are likely. Seismic methods have been tested for both reconnaissance and delineation but remain underemployed. Given the high cost of drilling in the North and the proven success of geophysical techniques in reducing exploration risk, it is likely that an increasingly diverse range of geophysical techniques and innovative interpretation techniques will continue to be applied in kimberlite exploration.

May 1, 2003

By Jas. E. Thomson

"The Omega mine is in McVittie township in the Larder Lake area, Ontario. Production at the mine commenced in 1936, and, until the end of 1946, ore milled amounted to 1,558,604 tons, from which 207,074 oz. gold and 28,205 oz. silver, valued at $7,585,470, were recovered. The mine workings extend to a depth of 1,975 feet.GEOLOGYThe geology of the mine has been described in detail by C. P. Jenney (l) and the writer (2). The general geology and structure in the vicinity of the mine is discussed on an earlier page in this volume. The rock formations found in the mine workings are indicated on the accompanying plan and section (Figs. 1and2). They consist of an intermingled, south dipping complex of volcanics, sediments, and secondary talc-chlorite schists and carbonates. The carbonatized rocks, which are often referred to as 'dolomite' in the Larder Lake camp, are siliceous-carbonate replacements in the talc-chlorite schist zones. In places they contain green mica, probably fuchsite, and are cut by a stockwork of quartz veinlets and stringers. A stock of syenitic intrusives lies south of the mine workings.STRUCTUREThe main structural features are indicated in Figs. 1 and 2. The formations and orebodies have a pronounced southerly dip, which flattens with depth. The talc-chlorite schist and 'dolomite' zones are part of the Larder Lake fault or 'break' on which there appears to be very large displacement. Evidence throughout the district would indicate that the south side moved up and, in the case of the Omega mine, the thrust may have been distributed throughout the several intensely sheared zones. This slice faulting could account for the repetition of sediments and volcanics. An alternative possibility would be original interbedding of volcanics and sediments."

Jan 1, 1954

By E. S. Moore

In the townships of Genoa and Marion, Subdury Mining Division, Ontario, there is a group of twenty-three mining claims known as the Jefferson claims. They are controlled by the Jefferson Mining Corporation and they were staked in 1908 by W. E. Smith, formerly of Sudbury, Ontario, and now of Smith & Reitz, a law firm of Minneapolis, Minnesota. These claims were staked for iron ore and in 1910 about 4000 feet of diamond-drilling was done on them. During the drilling operations galena and sphalerite ~were found in the iron formation in cores from holes, Nos. 2 and 3, claim W. D. 717, Genoa township. This discovery lead to a search for galena and sphalerite in the vicinity and a streak of rock containing these minerals was found in the iron formation a short distance to the east of. the drill holes. A shaft was sunk on this outcrop in 1912 to a depth of 8 feet and bottomed in an attractive lens of galena. Stripping revealed other small exposures of galena and sphalerite in the iron formation.

Jan 1, 1926

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By D. E. Ayres, J. Farstad

"The Midwest uranium deposit is located within the Athabasca Basin near its eastern margin and displays many of the features seen in a number of other similar deposits in this area. The mineralization occurs in the vicinity of a tectonically disrupted portion of the unconformity separating the clastic sedimentary rocks of the Helikian Athabasca Group from Aphebian pelitic meta-sediments which are equivalent to the basal pelitic meta-sediments of the Wollaston Group. The orebody consists of pods of massive pitchblende and sulphur-arsenides within an elongate and tablular envelope of disseminated and fracture controlled mineralization. The massive pods are intimately associated with overbank mudstones of the lowermost Athabasca Group. Both structure and lithology have played major roles in localizing the deposit as follows:1. The basement lithology influenced the mineralogy of the regolith produced on the pre-Athabasca unconformity.2. The style of clastic deposition and the character of the regolith on this unconformity favoured local preservation of mudstones.3. The basement lithology influenced the location of zones of post-Athabasca faulting.4. The proximity of these fault zones to mudstones provided for the coincidence of circulatory channels for fluids bearing uranium, with a good precipitant for the metal.IntroductionA brief summary of the geology of the Midwest uranium deposit was presented by J. Farstad (1979) to the attendees of the Saskatchewan Potash and Athabasca Basin uranium deposits field trip organized by the Canadian Institute of Mining and Metallurgy (May 28 to June 1, 1979). Since that time a substantial amount of data has been collected and studied. This paper is a precis of a report by J. Farstad (1981) which summarizes the geology of the deposit as inferred by visual examination of diamond drill core, augmented by information obtained from detailed examination of selected cores by D.E. Ayres."

Jan 1, 1986

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By D. C. Fraser

"Geophysical Engineering and Surveys Limited of the Keevil Mining Group have routinely conducted ground surveys with VLF-EM receivers for the past two years. Both Crone's Radem and Ronka's EM16 have been used.VLF-EM dip-angle data often yield complex patterns which require considerable study for a proper interpretation. A method was developed which allows field operators to transform the noncontourable dip angles into contourable data, producing conductor patterns which are immediately apparent to exploration personnel untrained in VLF-EM interpretation.VLF-EM contoured data generally peak very close to the top of a conductor, thereby allowing drill holes to be spotted accurately. However, the data generally should not be used alone to select drill targets because structures may be sufficiently conductive to yield strong anomalies. Thus, magnetic and/or vertical-loop EM correlations may be considered as necessary criteria for drilling.VLF-EM surveys can replace IP surveys in certain environments. For example, the Restigouche orebody in the Bathurst camp of New Brunswick yielded a VLF-EM anomaly as distinct as that obtained by IP, although the body did not respond to vertical-or horizontal-loop EM. However, the cupriferous breccia pipes of the Triba mine near Batchawana, Ontario yield strong IP anomalies but not VLF-EM anomalies, illustrating that disseminated ore targets should be sought with IP rather than with VLF-EM."

Jan 1, 1971

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

By W. J. Gibson

"This paper will provide a general assessment of the differences in construction and industrial labour relations. From this outline will come a detailed examination of labour relations in the construction industry and then specifically as related to the construction of mining projects, with emphasis on projects in isolated areas. Development of manpower forecasts, manpower availability, wage escalation formats, working rules, training and recruitment programs, and safety - as related to construction labour relations in the mining industry - are topics which will be dealt with."

Jan 1, 1972

By Burrows. A.

Temperature profiles in the lead smelter sinter bed at Xstrata Zinc Mount Isa sinter plant have been measured using a wireless temperature probe. Corresponding sinter samples have been collected for characterization. The sinter peak bed temperatures were found to be in the range of 1000 - 1200 °C. Microstructures and softening temperatures of these sinters have been characterised. Strong correlations have been observed between peak bed temperature and peak hood temperature, and between mean sinter softening temperature and peak bed temperature. It was found that higher peak bed temperature results in higher sinter softening temperature. For the feed material used in the trials, to obtain sinters with mean softening temperatures above 1050 °C, peak bed temperatures above 1130 °C are required. There appears to be a direct correlation between granule size distribution in the feed and peak bed temperature attained. High peak bed temperatures are observed in sinters with narrow granule size distribution.

Jan 1, 2008

By E. F. Evoy

"The Gunnar uranium deposit was within metasedimentary rocks of the late Archaen Tazin Group. These rocks were intensely altered by albitization so that the immediate host to the ore consisted dominantly of albite, and by the subsequent introduction of calcite. The ore consisted of disseminated pitchblende and uranophane in a pipe-shaped breccia zone. Oxidation of the ore was more intense near surface than at depth, but there was no near-surface enrichment.IntroductionThe Gunnar Mine site is on the tip of Crackingstone Peninsula, on the north shore of Lake Athabasca, Province of Saskatchewan, Canada. The peninsula forms the southern part of the Beaverlodge mining area. The ore consisted of disseminated pitchblende and uranophane in brecciated metasedimentary rocks of the Tazin Group, and the deposit was characterized by extreme albitization and subsequent carbonatization of the host environment.Production from the mine began in 1954 and the ore was depleted by 1963. In that interval the deposit yielded about 5 million tonnes of ore containing about I. 75 kg/tonne U3O8. It was mined initially from an open-pit and subsequently from underground; the open-pit contributed about 55% of total tonnage. Uranium was recovered by atmospheric leaching in sulphuric acid, ion exchange concentration, and precipitation with magnesia.This paper is based on studies made during the productive life of the mine and is concerned primarily with pre-ore alteration of the rocks containing the deposit, and with the ore mineralogy."

Jan 1, 1986

By Zou Lisheng

The culture of safety is very important to coal mining production. About 90% of mine accidents are caused by human error. This paper analyzes the status of China?s coal mining accidents, and accident cause. This paper explains the concept of safety culture, the value of safety culture, as well as the relationships between safety culture and safety behavior, and between safety culture and science and technology. The paper proposes the model of safety culture and the ways to enhance safety culture of coal enterprises. Safety culture and safety production is closely related and are significant to the improvement of mine safety situation in China.

Aug 1, 2013

By C. V. Corless

THE origin of various types and groups of ore deposits was some years ago a subject of much controversy. To this statement the copper-nickel deposits near Sudbury afforded no exception. Not since the Report of the Ontario Nickel Commission, in 1917, has there been any serious discussion of the origin of this very important group. This may be because, from the opening-up of Murray mine by the British America Nickel Corporation until the recent work at Frood mine, no new ore-body of importance has been developed in the district. The controversy fifteen or twenty years ago between those who favoured the theory of magmatic segregation, among whom Dr. A. P. Coleman was the leading exponent, and those who considered that most, if not all of the Sudbury deposits could more satisfactorily be accounted for by the theory of replacement, will be remembered by many members of the Institute. Perhaps, as too often happens in controversial discussion, each side tended to overemphasize the importance of those geological phenomena which seemed to be most easily accounted for by the theory it favoured. A more balanced view would perhaps admit that replacement was probably predominant in the formation of most of the offset deposits, and magmatic segregation in that of most of the marginal deposits . But there is danger in generalization. Each body of ore should be studied by itself, and no general conclusion of this kind should be allowed to warp the judgment in making such a study.

Jan 1, 1929

By L. Rahnenfuhrer

"Hoisting equipment is a vital part of the operation of most producing mines. Safety and continuation of operation necessitates ultrasonic preventive maintenance inspection on a regular basis.Ultrasonic inspection of hoist shafting, brake linkage and draw bars will contribute to a safe operation and can prevent costly unscheduled shut-down time. With little dismantling, ultrasonic testing techniques can be applied to. determine the conditions of shafting and linkage in hoisting equipment, mining equipment and other miscellaneous mining equipment."

Jan 1, 1969

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By Charles "Chick" Rodgers, Anthony Sarion

"With declining feed grade and increased production targets, it became necessary to upgrade Key Lake's eight stage counter current decantation (CCD) circuit. Following laboratory trials, mill operations recognized that dilution of the feed slurry and buffering of the feed density variations would improve thickener throughput. Plant testing resulted in the installation of Outokumpu's Supaflo ""Floe-Miser"" system. The circuit's flowsheet, instrumentation and control strategy were also upgraded along with the thickener feedwell modifications. The paper will also discuss these modifications and the implementation of the current control strategy.IntroductionCameco Corporation's Key Lake operation is the largest single uranium producer in the world. Current production is fourteen million pounds of uranium oxide (U 308) per year. It is owned 2/3 by Cameco and 1/3 by Uranerz Exploration and Mining with Cameco as the operator.The mine is 570 kilometres north of Saskatoon on the southern edge of the Athabasca basin. Access to the mine is by an all-weather road and a private airstrip.Process DescriptionThe Key Lake milling process consists of five individual plants: crushing and grinding; leaching and counter current decantation (CCD); solvent extraction; yellowcake precipitation and ammonium sulphate crystallization; and bulk neutralization (Figure 1 -Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1998

By Marty Hudyma

There are five independent seismic source parameters: seismic energy, seismic moment, source size, location, and time. These parameters are investigated primarily for evaluating seismic hazard and understanding seismic source mechanism(s). Broadly, seismic hazard is the likelihood of occurrence of an event of a given magnitude. Seismic source mechanism is the mode of rockmass failure that causes the seismic event. Most mine seismicity analysis techniques use a combination of a few of the independent source parameters. In literature, time is perhaps the least discussed and most underutilized of these five parameters. This paper discusses three applications of time to understand both seismic hazard and seismic source mechanism in mines. The first application is time history analyses, which focuses on how other parameters of interest vary over time. Examples are presented to show how time history analyses can give information about both seismic hazard and seismic source mechanism. The second application is analysis of time-between-events. This technique can give insight into seismic source mechanism. The final application is phasor analysis using the Schuster test. This method can be used to investigate how seismic source mechanisms may change over time. For both time-between-events analysis and phasor analysis, there are important implications with regards to scale dependence and the breakdown of self-similarity of mining-induced seismicity.

Jun 1, 2012