Search Documents

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has 'been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

By Karl J. C. Harries

"10.1. INTRODUCTIONDefinitions are a necessary part of every agreement. Their purposes are to assist the reader in reading and understanding an agreement and to attempt to avert potential confusion and, therefore, disputes. In some circumstances, they may be critical in deciding a dispute. As they are often substantive, they should not be treated lightly.It is far easier and less confusing for a reader to read “the Company” or “the Recipient” than to be faced with “the party of the First Part”, or to see the “Jones Property” than “that part of the property hereinbefore described in paragraph 1.01 hereof”. It is also advisable not to use “-ee” and “- or”, as in payee and payor.One thing must always be remembered: once a word has been defined in an agreement, it will always have the defined meaning unless the contrary is clearly indicated or is required to make sense of a provision.2 It can be confusing for a reader if commonly used words are defined in other than ordinary terms. Unique words that will stand out in the text are more likely to be recognized as having special meaning. It is also good practice to identify defined terms by capitalizing them in the text of the agreement. Boldfacing of definitions is also sometimes used for this purpose but, as boldfacing is not easily identified in handwritten revisions, it can be missed in the press of negotiations, especially when several typists are involved. Lack of consistency in identifying defined terms is not a fatal mistake, but it can create confusion, especially if the reader is new to the agreement or is reading it in a highly technical manner, such as when there is a dispute.If definitions used in the main text also apply to a schedule, they need not be included in both. Omitting them from the schedule makes the agreement look shorter, which to some people is a benefit. If definitions are not repeated, make certain that the schedule clearly indicates that words defined in the main text have the same defined meanings in the schedule3 and are clearly identified as defined words. In considering whether or not to repeat in a royalty schedule definitions appearing in the agreement proper, think of definitions as an aid and a reminder to the reader. Repeating them will help a reader, if only by saving the nuisance of remembering where to find them in the main text and constantly turning to it. All the definitions needed to read the schedule will be right there, so that the schedule is a self-contained document. Just make certain that, if you do repeat a definition, you repeat it in identical terms. If you have to change any defined term to make it fit the royalty provisions, use a different word or phrase as the defined term to warn the reader that he is dealing with a different concept.4"

Jan 1, 2003

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -'}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Brandt Porter, Lawrence K. Nordell, Alexander Potapor

"Improving comminution efficiencies with better machine geometries and motions, improved nip angles, rock movement control, and voids regulation among rocks are some of the next steps to better machine performance. Recent gains (~30%) using high pressure grinding rolls (HPGRS) and vertical roller mills, in theory and practice, are based on Prof. Klaus Schönert’s academic studies (1979–1996) on rock breakage physics. More recently, University of British Columbia Prof. Bern Klein’s studies (2006–present) via the Ph.D. thesis of Z. Davaanyam (2015) further validate theory with practice from laboratory measurements used in this paper.They demonstrated ideal rock compression breakage, within HPGR and vertical roller mill machines using a piston-die apparatus. Similar rock size range is used. The piston-die confine rock breakage behavior. However, these studies do not extend to larger rocks (> 75 mm), and do not demonstrate the influence of rock voids among bifurcation of rocks during comminution. Further, machines fed with larger rock sizes, such as gyratory, jaw, and cone crushers, are not designed or evaluated for geometry nip angle efficiency.Herein we illustrate a performance gain of a new comminution machine, the conjugate anvil-hammer mill (CAHM), first presented at SAG 2011 (Nordell, 2012). The CAHM machine digests rock sizes 400% larger than HPGR, improves rock grip/nip geometry, better improves rock voids, improves surface wear life > 500%, and improves rock containment and slippage during compression. In all, the CAHM machine shows 22 potential improvements over the HPGR. Most importantly, CAHM shows a 50% kWh/ton improvement compared to the HPGR. Our studies use an advanced Discrete Element Method (DEM) computer program called ROCKY. ROCKY simulates moving boundaries, surface wear mechanics, and incorporates rock breakage physics based on the fundamentals of JKMRC T10 protocol [×] with tuned A × b breakage parameters.We calibrate rock breakage in our DEM code to mimicking both UBC laboratory piston-die and HPGR comminution measurements. We then model CAHM with these known ore and machine properties. Differences are illustrated using DEM techniques on each machine, including key points of when each: use geometry; initiate bifurcation breakage; provide a map of particle size distribution by location; illustrate the importance of controlling voids to minimize agglomeration after breakage; machine performance limits; and kWh/ton benefit."

Jan 1, 2016

By R. Simonson

Agenda ? Need and Introduction ? Interface Management Programs ? Outcomes of Successful Interface Management ? Key Success Factors ? Lessons Learned ? Concluding Remarks Need for Interface Management ? Complex projects ? Larger in scale ? Physically dispersed and delivered remotely ? Involved with several stakeholders ? Risks thus imposed due to: ? Iterative and dynamic nature ? Large information flow ? Document revisions and information updates ? Related sources of Risk: ? Ineffective communication ? Poor work relationships ? Person to job mismatches ? Failure to clarify expectations

Aug 1, 2013

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By Piotr Litwa

The paper focuses on actions aiming at improvement of work safety in mines, particularly in those extracting hard coal, taking into account the characteristics of natural hazards in Polish underground mining and the reasons of mining disasters connected with those hazards. It refers to conclusions addressed to scientific and research centres, drawn during last decade by Commissions appointed by the President of the State Mining Authority in order to investigate reasons and circumstances of incidents, which till now, could not have been accomplished because of financial reasons. Furthermore, the paper presents basic assumptions of the Strategic Research Project Improvement of work safety in mines, announced by the National Centre for Research and Development at State Mining Authority?s President request.

Aug 1, 2013

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

"Each and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Several factors including ore heterogeneity and harsh production environment affect the reproducibility of the reported data. Best practices of metal accounting thus prescribe that production reports be accompanied by measurement quality reports quantifying the reproducibility (a data quality metric often expressed as a relative standard deviation) of each data reported. Ignoring the irreproducibility of measurements may lead to the perception that random errors have been totally eliminated through statistical data reconciliation, which is wrong. This paper aims at explaining the full lifecycle management of reproducibility estimation from the outset at the measurement process to its reporting after having been through the statistical data reconciliation process. Indeed, the reproducibility of reported data can be obtained by performing a sensitivity analysis. Necessary conditions for obtaining a truly representative assessment of measurement reproducibility are stated. Typical levels of measurement reproducibility found in operating flotation plants are also reported. These numbers can be used as benchmarks for reproducibility levels that can be realistically expected.IntroductionEach and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Such production reports are the most expected output from a metal accounting system (MAS). The duly recurrence of this task combined with an insufficient level of automation has somehow contributed to the misleading perception that it is mainly a clerical work. However, as shown in Figure 1, a MAS encompasses way more than just a reporting system. Acknowledging that the content of production reports indubitably origin from raw measurements has important implications for how both the reports and MAS should be monitored."

Jan 1, 2016

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009

By James Scott

Outline Deposit Overview and Brief History ?Geologic Setting ?Local Geology ?Petrography ?Geochemistry ?Mineralization ?Geochronology ?Conclusions Deposit Overview ?Porphyry Cu-Mo-Au ?Discovered 1957 (BIK Syndicate) ?Various programs, most significant: ?Hecla(1970s) ?Teck(Late 1970s Early 1980s) ?Copper Fox Metals (2005 -Ongoing ?optioned from TeckComincoin 2002) ?Measured and Indicated Resources: ?847Mt grading: ?0.292% Cu ?0.019% Mo ?0.202g/t Au ?1.796g/t Ag ?Total ~ 0.485 % Cu Eq.

May 1, 2006

By Michael B. Cortie

Mesoporous gold sponge has the unique property of being both metallic and highly resistant to oxidation. It has potential application in catalysis, in bio-sensors, in optical coatings, in analytical chemistry and, as we show here, as the basis for a new kind of ultra-capacitor. Due to the cost of gold, the most probable niche for a gold-based ultra-capacitor would be in the high-power/high-energy regime, a region where gold would compete with devices based on RuO2. A high internal resistance limits the power that can be usefully drawn from existing carbon-based ultra-capacitors, and that this problem can potentially be overcome by gold-based devices. A simple proof-of-concept ultra-capacitor based on mesoporous gold is described and its behaviour during charge and discharge cycles examined. In this work a step change in the input or output voltage of the device was used as the controlling parameter. There was also a residual faradaic current resulting from traces of undissolved aluminium left over from the AuAl2 precursor used to make the sponge, and some charge storage due to polarization of the solution. Deconvolution of these three effects was not entirely accomplished, but an ostensible capacitance of about 7 to 14 mF/g Au was demonstrated. Further improvement from these early results seems likely.

Oct 1, 2003

By Oy Leuangthong

Red Dog mine is the world's largest Zn producer. The deposit consists of sulphide ore zones in sedimentary exhalative (sedex) deposits, and is characterized by the presence of multiple metals and multiple ore types. The objective of the case study is to characterize seven different minerals, Zn, Pb, Fe, Ba, sPb, Ag and TOC, within eight different rock types. Geostatistical models were constructed for each variable within the eight rock types, and subsequently assembled to give 40 realizations for six 25ft benches. The stepwise conditional transformation was used to account for the complex multivariate relations. In addition to reproducing the input data, histogram and variogram, the resulting models also respect multivariate relations locally and globally. This paper documents the methodology to construct these models. A thorough validation procedure was implemented. Comparisons with blasthole data show that the conditional simulations and the long-term models agree in expected value. The main advantages of the conditional simulations are (1) the explicit accounting of multivariate relations between the data in model construction, and (2) the ability to quantify variability and uncertainty at any scale. A small exercise comparing the profit from a kriged and a simulated model is also examined. Results show that the simulation approach showed a 3% increase in profit, relative to the conventional estimation approach.

May 1, 2004